Desa VTD-24PV-JHB, VTD-30NV-JHB, VTD-30PV-JHB, VTD-24NV-JHB Table of Contents, Safety Information

Page 2

Table of Contents

Safety Information

2

Specifications

12

Product Identification

4

Troubleshooting

13

Local Codes

5

Service Hints

17

Unpacking

5

Technical Service

17

Product Features

5

Replacement Parts

17

Optional Accessories

5

Accessories

17

Installation

5

Wiring Diagrams

17

Operating Appliance

10

Illustrated Parts Breakdown and Parts List

18

Inspecting Burners

12

Warranty Information

Back Cover

Cleaning and Maintenance

12

 

 

 

Safety Information

WARNING: Improper in- stallation, adjustment, al- teration, service or main- tenance can cause injury or property damage. Refer to this manual for correct installation and operation- al procedures. For assis- tance or additional infor- mation consult a qualified installer, service agency or the gas supplier.

This appliance may be in- stalled in an aftermarket,* permanently located, manufactured (mobile) home, where not prohib- ited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

WARNING: This appli- ance is for installation only in a solid-fuel burn- ing masonry or UL127 factory-built fireplace, constructed of noncom- bustible material and connected to a working flue. (See page 6 for mini- mum flue opening.)

WARNING: This is a gas- fired heater. It uses air (oxygen) from the room in which it is installed. Provi- sions for adequate com- bustion and ventilation air must be provided. Refer to the National Fuel Gas Codes, ANSI Z233.1/NFPA 54,Section5.3,AirforCom- bustion and Ventilation.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.

www.desatech.com114370-02C

Page 1 Page 3
Image 2
Page 1 Page 3
Contents What to do if YOU Smell GAS Ansi Z21.60-2003 CSATable of Contents Safety InformationSafety Information Product Identification AssemblySwitch Log SetInstallation Product FeaturesOptional Accessories Local CodesVenting Specifications for Installation Installation and ClearancesFlue Opening Specifications Installing Damper ClampInstallation Items Needed Installing Appliance AssemblyConnecting to GAS Supply Flexible Gas Hose If Allowed by Local Codes Control ValveNatural Gas Checking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaOperating Appliance For Your Safety Read Before LightingPressure Testing Appliance Gas Connections Lighting InstructionsControl Knob Ignitor Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off ApplianceInspecting Burners Cleaning Maintenance SpecificationsFor purpose of input adjustment Burner Flame PatternTroubleshooting Observed Problem Possible Cause RemedyHas been triggered Causing pilot flame to go Out. This problem could beControl Delayed ignition of burner Manifold pressure is too Ignition operationTurn control knob to LO Noise when burners are lit Position when burners areWhite powder residue forming When heated, vapors from Cold Minute Air in gas line Operate burners until air isGas leak. See Warning Statement at topReplacement Parts Service HintsTechnical Service AccessoriesIllustrated Parts Breakdown Models VTD-18NV-JHB, VTD-24NV-JHB, VTD-30Nv-JHBParts List Parts on page 17 of this manualLimited Warranty Vented GAS Logs Warranty InformationKeep this Warranty
Top Page Image Contents