Desa VYGF33PRC installation manual Fpvf Models Only, Installing Remote Receiver Unit

Page 18

INSTALLATION

Continued

FPVF Models Only

1.Place one-piece log set on grate to ﬁt as illus- trated in Figure 31. Make sure middle section at bottom of log set is seated into “U”-shaped cutout in center of chassis (see Figure 31). IMPORTANT: Make sure log does not cover any burner ports (see Figure 32).

2.Install ﬁreplace screen by slipping notches of ﬁreplace screen over screws on front of ﬁreplace (see Figure 30, page 17).

WARNING:You must operate this ﬁreplace with the ﬁreplace screen in place. Make sure ﬁre- place screen is in place before running ﬁreplace.

One Piece

Log Set

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES (GHRCB and GHRCTB)

Installing Remote Receiver Unit

1.Disconnect switch wires from the control valve.

2.Remove screws attaching switchplate.

3.Remove switch plate (see Figure 33). Discard after removing.

4.Install remote receiver unit onto gas log heater base using mounting clips.

5.Push clips ﬁrmly into place (see Figure 34).

6.Connect wires as shown in Figure 35.

Remote	Ignitor
Switch
Bracket

Screw

Middle

Section at

Bottom of

Log Set

Burner

	Chassis	"U" Shaped
	Chassis	Cutout In
		Cutout In
		Chassis
	Figure 31 - Installing One Piece Log Set
	Burner Ports	One Piece
		One Piece
		Log Set

Figure 32 - Installing One Piece Log Set, Top View

Switch Plate

Wires

Figure 33 - Switch Plate and Wiring

Harness

Mounting

Clips

Remote Receiver

Figure 34 - Installing Remote Receiver

White Wire

From Receiver

Valve

Red Wire From

Receiver

Figure 35 - Connecting Wires

18

www.desatech.com

113109-01B

Image 18

Contents What to do if YOU Smell GAS Patent PendingTable of Contents Safety Information Log Base Assembly Product IdentificationUnpacking Product FeaturesLocal Codes AIR for Combustion VentilationUnusually Tight Construction Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Conﬁned and Unconﬁned SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstalling Hood Electrical HookupInstallation Clearances Repeat steps 1 through 6 for other sideConventional Fireplace Installation Placing Hearth Base Accessory Against WallBUILT-IN Fireplace Installation Models VYGF33PRB and VYGF33NRBConnecting Duplex Outlet Models FPVF33PRA and FPVF33NRAInstalling GAS Piping to Fireplace Location Mantel Clearances for Built-In InstallationInstallation Items Needed Connecting Fireplace to GAS Supply Natural GasPropane/LP Checking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaPressurize supply piping system by either Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaInstalling Logs Vygf Models OnlyInstalling Remote Receiver Unit Fpvf Models OnlyInstalling 9-Volt Battery in Receiver Installing 9-VOLT BatteriesFor Your Safety Read Before Lighting Installing 9-Volt Battery in Hand-Held Remote Control UnitLighting Instructions Pilot Propane/LPOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance ON/OFF Series Model GhrcbThermostat Series Model Ghrctb Optional Blower OperationBurner Flame Pattern Inspecting BurnerPilot Flame Pattern Burner Primary AIR HolesCleaning Maintenance Burner Injector Holder and Pilot AIR Inlet HoleLogs Troubleshooting Observed Problem Possible Cause RemedyDiagram, Maintenance, Fireplace produces unwanted Gas leak. See WarningReplacement Parts Wiring DiagramSpecifications Technical ServiceIllustrated Parts Breakdown Models VYGF33PRC and VYGF33NRC ShownParts List Models FPVF33PRA and FPVF33NRA KEY Part Number FPVF33PRA FPVF33NRA Description QTY Firebox Models VYGF33PRC and VYGF33NRC KEY Part Number Description QTY Firebox Models FPVF33PRA and FPVF33NRA Parts List Accessories Cabinet Mantel and Full Hearth Base Receiver and HAND-HELD Remote Control KIT Ghrcb SeriesWALL-MOUNT ON/OFF Switch Laminate Trim for Hearth or MantelWarranty Information Keep this WarrantyLimited Warranty VENT-FREE GAS Fireplace