Desa (V)T36EPA Glass soots Flame impingement on logs, Flame does not excessively, Mixer, Burner

Page 33

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

 

 

Glass soots

1. Flame impingement on logs

1.

Adjust the log set so that the

 

 

 

 

flame does not excessively

 

2.

Debris around burner air

2.

impinge on it

 

Inspect the opening at the base

 

 

mixer

 

of the burner to see that it is

 

 

 

 

NOT packed with any type of

 

 

 

 

material

 

Remote does not function

1. Battery is not installed. Bat-

1.

Replace battery in hand-held

 

 

tery power is low

 

remote

 

Dark residue on logs or inside of

1. Improper log placement

1.

Properly locate logs (see log

fireplace

2.

Air holes at burner inlet

2.

placement sections on page 24)

 

Clean out air holes at burner

 

 

blocked

 

inlets. Periodically repeat as

 

3.

Burner flame holes blocked

3.

needed

 

Remove blockage or replace

 

4.

Improper venting or excessive

4.

burner

 

Have the vent system inspected,

 

 

blockage

 

including the termination cap.

 

 

 

 

Remove any restrictions or

 

5.

Excessive amounts of embers

5.

obstruction

 

Clear excess embers until a

 

 

and pan material

 

minimum gap of 1/2" remains

 

 

 

 

under the grate

111251-01E

www.desatech.com

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents What to do if YOU Smell GAS Safety Information Table of ContentsSafety Information Local Codes Product FeaturesProduct Identification High traffic areasPre-Installation Preparation Location and space requirementsProper clearances must be maintained Framing and finishing ClearancesFront Top of Standoffs Vent See venting Venting clearancesBalcony with Perpendicular Side Wall Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior 32 min Ground Floor InstallationRecommended Applications Corner ground floor installation Snorkel Termination InstallationHorizontal System Installation Using TWO 90 Elbows Installation for vertical termination Flat Ceiling InstallationConnect a section of pipe and extend up through the hole Twist-lock the vent cap onto the last section of vent pipe Vertical Venting High Altitude InstallationDesa Elbows Desa Venting AccessoriesDesa Terminations Number DescriptionInstalling optional blower accessories Fireplace InstallationModel BK Installation Check GAS TypePlug in blower power cord to duplex outlet Model BKT InstallationInstalling Gas Piping to Fireplace Location Blower Wiring DiagramInstallation Items Needed Checking GAS Connections Connecting Fireplace to GAS SupplyTest Pressures Equal To or Less Than Psig 3.5 kPa Pressure Testing Fireplace Gas ConnectionsRemoving/Replacing Glass Door Cleaning Glass DoorRemoving Louver Panels Removing Glass DoorClose top and bottom louvers Installing logs, lava rock and glowing embersInstalling Log No Optional Remote control Installation model WRC Wall Switch InstallationOpen lower louver panel of firebox Wiring Diagram Pilot GasLine For your safety Read before lighting Operating FireplaceLighting Instructions To Turn OFF GAS To Appliance Inspecting BurnersOptional Remote Operation Burner Flame PatternGlass Door Cleaning MaintenancePilot and burners LogsTroubleshooting Cleaning and MaintenanceObserved Problem Possible Cause Remedy Venting systemGas leak. See Warning Improper log placement Tery power is low RemoteClean out air holes at burner Glass soots Flame impingement on logsIllustrated Parts Breakdown Parts List Illustrated Parts Breakdown KEY Description Service Hints Replacement PartsTechnical Service SpecificationsAccessories Warranty Information Keep this WarrantyLimited Warranty DIRECT-VENT Fireplace
Top Page Image Contents