Desa CSDBN, CSDPBN installation manual Installing Optional Wall Mounted Thermostat GWMT1

Page 23

STOVE AND BURNER SYSTEM INSTALLATION

Installing Optional Wall Mounted Thermostat - GWMT1 Installing Optional Wireless Hand-Held Remote Control Accessories - GHRCB and GHRCTB Series

23

STOVE AND BURNER SYSTEM INSTALLATION

Continued

INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1

WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Open lower door panel. The valve is attached to the underside of the burner system assembly.

2.Disconnect from the valve the wires running from the ON/ OFF switch.

3.Connect one terminal of the wire for the wall thermostat to the THTP terminal on the valve. Connect remaining wire terminal to the TH terminal on the valve. Make sure that the wire termi- nals are in the positions on the unit as pictured in Figure 48, page 22. If wires are not connected as shown the thermostat will not work.

4.Route the wire to a convenient location to mount your thermo- stat (no outside wall). IMPORTANT: The wire must not ex- ceed 25 feet in length. The thermostat should be mounted 54" above the floor in a location where there is good air circula- tion. Avoid heat sources such as lamps, direct sunlight, fire- place, or heat and air conditioning ducts.

5.Gently remove the cover of the thermostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

6.Feed the electrical wires through the rectangular slots (from the back) on each side of the base (see Figure 49).

WARNING: Do not connect this thermostat to a power source. Electrical shock and/or fire hazard will occur.

7.Connect one bare wire end to each terminal (“W” and “R”) of the thermostat base (see Figure 50).

8.Install the base to the wall with screws provided with thermostat.

9.Move the temperature adjustment back and forth to insure the bimetal is free from restrictions.

10.Replace the cover onto the base. (Upon installation, the ther- mostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation.)

11.Set the temperature adjustment to the desired setting. This ther- mostat has been electronically calibrated at the factory. No ad- justment or leveling is necessary.

Feed wires through rectangular slots

Terminal “W”

W

 

Terminal “R”

 

R

Figure 49 - Back View of

Figure 50 - Thermostat

Thermostat Base

Base Terminal “W” and “R”

INSTALLING OPTIONAL WIRELESS HAND- HELD REMOTE CONTROL ACCESSORIES - GHRCB AND GHRCTB SERIES

NOTICE: Use only alkaline batteries (not included).

Installing Remote Receiver and 9-volt Alkaline Battery

1.Open bottom door on stove body.

2.Disconnect wires from THTP and TH on control valve that lead to the switch (see Figure 48, page 22). Discard switch plate, screws, and nuts.

3.Install 9-volt battery (not included) into receiver battery clip and connect to terminals (see Figure 51).

Receiver

9-Volt

BatteryTerminal Wires

Battery Clip

Figure 51 - Installing Battery in Receiver

For morevisit www..com

111739-01A

Page 22 Page 24
Image 23
Page 22 Page 24
Contents For Your Safety What to do if YOU Smell GAS OWNER’S Operation and Installation ManualFor Your Safety Safety Information Table of ContentsON/OFF Product IdentificationGlossary of Terms PRE-INSTALLATION Preparation Product FeaturesLocal Codes Unpacking Stove PRE-INSTALLATION PreparationStove and Burner System Assembly REMOVING/REPLACING Doors and Glass Installing Optional Blower AccessoryPlace the green ground wire between the bottom hole on Thermostat Blower Only Attach thermal switch and bracketAngle see . This will allow thermal switch to be Operating modeBurner, Main Burner Orifice, and Pilot Orifice Conversion Installing PROPANE/LP Conversion KITGas Control Valve Conversion Conversion Labeling and PlacementLocation of Vent Termination Installing Rear CoverGeneral Venting General Venting Installation Planning Venting InstallationInstallation Precautions Installing Vent System in a Chase Installation for Horizontal TerminationInstalling Horizontal Vent Cap Noncombustible Exterior Venting with Two 90 Elbows Horizontal Termination ConfigurationsHorizontal Venting Flat Ceiling Installation Installation for Vertical TerminationVenting with One 90 Elbow Cathedral Ceiling InstallationVertical Termination Configurations Elbows Vertical Venting Configuration Using Two 90 ElbowsNumber Description High Altitude InstallationParts Lists for Venting Kits and Components Vertical VentingCheck GAS Type Stove and Burner System InstallationInstalling GAS Piping to STOVE/ Burner System Location Installation Items NeededChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Pressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Remote Receiver and 9-volt Alkaline Battery Installing Optional Wall Mounted Thermostat GWMT1Remove glass door. See Removing/Replacing Glass Door, Installing LOGS, Lava Rock and Glowing EmbersLighting Instructions For Your Safety Read Before LightingOperating Stove with Burner System Shutting Off Burners Only pilot stays lit Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional HAND-HELD Remote OperationON/OFF Series Model Ghrcb Manual ModeAuto Thermostatic Mode Safety FeaturesOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause TroubleshootingCompany Improper vent configurationOrifice Inlet gas pressure is too lowAbove Gas leak. See Warning statementParts Under Warranty SpecificationsWiring Diagram Replacement PartsModel Sdvbnc Illustrated Parts BreakdownKEY Part Number Description Parts ListStove Chassis Models Csdbn and Csdpbn KEY Part Number Csdbn Csdpbn Description QTY Stove ChassisAccessories Technical ServiceService Hints Owners Registration Form Postage Required 111739-01A Warranty Information

CSDBN, CSDPBN specifications

Desa CSDPBN and CSDBN represent cutting-edge advancements in the realm of community-driven development and data-centric governance. These initiatives are designed to empower local communities by integrating technology with robust administration strategies to enhance public service delivery, economic development, and social welfare.

One of the main features of Desa CSDPBN is its focus on participatory governance, allowing community members to actively engage in decision-making processes. This framework encourages transparency and accountability, enabling citizens to voice their needs and priorities while fostering a sense of ownership over local projects. Such involvement helps create tailored solutions that effectively address the specific challenges faced by the community.

Technologically, Desa CSDPBN leverages an array of digital tools that facilitate real-time data collection and analysis. This includes geographic information systems (GIS) and mobile application development to gather insights on resource allocation, infrastructure needs, and demographic information. By employing data analytics, local governments can make informed decisions that enhance resource distribution and service delivery.

The characteristics of CSDPBN and CSDBN systems also extend to their adaptability and scalability. These frameworks are designed to be flexible, allowing them to be replicated across different regions with varying socio-economic contexts. This scalability ensures that diverse communities can benefit from the same foundational principles while customizing aspects to suit their unique environments.

Further enhancing their effectiveness, both initiatives incorporate capacity-building efforts aimed at training local leaders and stakeholders in the use of technology and project management. Such educational components empower communities to sustain development initiatives while fostering local expertise.

Additionally, the integration of social media and online platforms within the Desa CSDPBN framework promotes civic engagement and collaboration among community members. This connectivity nurtures a sense of unity and collective responsibility while improving communication between citizens and local authorities.

Ultimately, Desa CSDPBN and CSDBN embody a holistic approach to community development by harmonizing technology, governance, and citizen participation. They represent a transformative model that not only addresses immediate development needs but also lays the groundwork for sustainable growth and resilience in local communities. As these practices gain traction, they pave the way for a more equitable and inclusive future, where every voice contributes to the narrative of progress.
Top Page Image Contents