Desa CSDPBN, CSDBN Installation for Vertical Termination, Flat Ceiling Installation

Page 16

16

VENTING INSTALLATION

Installation for Vertical Termination

VENTING INSTALLATION

Continued

INSTALLATION FOR VERTICAL

TERMINATION

NOTICE: Use rigid pipe only. Flex venting is not to be used with a vertical termination.

1.Determine the route your vertical venting will take. If ceiling joists, roof rafters, or other framing will obstruct the venting system, consider an offset (see Figure 34) to avoid cutting load bearing members. Note: Pay special attention to these installa- tion instructions for required clearances (air space) to combus- tibles when passing through ceilings, walls, roofs, enclosures, attic rafters, etc. Do not pack air spaces with insulation. Also note maximum vertical rise of the venting system and any maxi- mum horizontal offset limitations. Offsets must fall within the parameters shown in Figures 38 through 40, pages 17 and 18.

2.Set the stove in desired location. Drop a plumb line down from the ceiling to the position of the burner system exit flue. Mark the center point where the vent will penetrate the ceiling. Drill a small locating hole at this point.

Drop a plumb line from the inside of the roof to the locating hole in the ceiling. Mark the center point where the vent will penetrate the roof. Drill a small locating hole at this point.

Roof

Flashing

Wall Strap

45° Elbow

Flat Ceiling Installation

1.Cut a 10" (25.4 cm) square hole in the ceiling using the locat- ing hole as a center point. The opening should be framed to 10" x 10" (25.4 cm x 25.4 cm) inside dimensions, as shown in Figure 27 on page 14 using framing lumber the same size as the ceiling joists. If the area above the ceiling is an insu- lated ceiling or a room, nail firestop from the top side. This prevents loose insulation from falling into the required clear- ance space. Otherwise, install firestop below the framed hole. The firestop should be installed with no less than three nails per side (see Figure 35).

2.Assemble the desired lengths of pipe and elbows necessary to reach from the burner system flue up through the firestop. All connections must be sealed with high temperature sili- cone sealant as specified in the second warning statement on page 12. Be sure all pipe and elbow connections are fully twist-locked (see Figure 26, page 13).

3.Cut a hole in the roof using the locating hole as a center point. (Cover any exposed open vent pipes before cutting hole in roof.) The 10" x 10" (25.4 cm x 25.4 cm) hole must be measured on the horizontal; actual length may be larger depending on the pitch of the roof. There must be a 1" (2.54 cm) clearance from the vent pipe to combustible materials. Frame the opening as shown in Figure 27 on page 14.

4.Connect a section of pipe and extend up through the hole.

Note: If an offset is needed to avoid obstructions, you must support the vent pipe every 3 feet (0.91 m). Use wall straps for this purpose (see Figure 34). Whenever possible, use 45° elbows instead of 90° elbows. The 45° elbow offers less re- striction to the flow of the flue gases and intake air.

5.Place the flashing over the pipe section(s) extending through the roof. Secure the base of the flashing to the roof and framing with roofing nails. Be sure roofing material overlaps the top edge of the flashing as shown in Figure 34. There must be a 1" (2.54 cm) clearance from the vent pipe to combustible materials.

If area above is a room, install

If area above is not a

firestop above framed hole.

room, install firestop below

 

framed hole.

Ceiling Firestop

Figure 34 - Offset with Wall Strap and 45° Elbows

Figure 35 - Installing Firestop

For..com

111739-01A

Page 15 Page 17
Image 16
Page 15 Page 17
Contents For Your Safety OWNER’S Operation and Installation ManualFor Your Safety What to do if YOU Smell GAS Table of Contents Safety InformationProduct Identification ON/OFFLocal Codes PRE-INSTALLATION Preparation Product FeaturesGlossary of Terms Stove and Burner System Assembly PRE-INSTALLATION PreparationUnpacking Stove Installing Optional Blower Accessory REMOVING/REPLACING Doors and GlassThermostat Blower Only Attach thermal switch and bracket Angle see . This will allow thermal switch to beOperating mode Place the green ground wire between the bottom hole onInstalling PROPANE/LP Conversion KIT Burner, Main Burner Orifice, and Pilot Orifice ConversionConversion Labeling and Placement Gas Control Valve ConversionGeneral Venting Installing Rear CoverLocation of Vent Termination General Venting Installation Precautions Venting InstallationInstallation Planning Installation for Horizontal Termination Installing Vent System in a ChaseInstalling Horizontal Vent Cap Noncombustible Exterior Horizontal Venting Horizontal Termination ConfigurationsVenting with Two 90 Elbows Installation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations Cathedral Ceiling InstallationVenting with One 90 Elbow Vertical Venting Configuration Using Two 90 Elbows ElbowsHigh Altitude Installation Parts Lists for Venting Kits and ComponentsVertical Venting Number DescriptionStove and Burner System Installation Installing GAS Piping to STOVE/ Burner System LocationInstallation Items Needed Check GAS TypePressure Testing Gas Supply Piping System Connecting STOVE/BURNER System to GAS SupplyChecking GAS Connections Installing Optional Wall Mount Switch GWMS2 Pressure Testing Burner System Gas ConnectionsInstalling Optional Wall Mounted Thermostat GWMT1 Installing Remote Receiver and 9-volt Alkaline BatteryInstalling LOGS, Lava Rock and Glowing Embers Remove glass door. See Removing/Replacing Glass Door,Operating Stove with Burner System For Your Safety Read Before LightingLighting Instructions Manual Lighting Procedure To Turn OFF GAS To ApplianceOptional HAND-HELD Remote Operation Shutting Off Burners Only pilot stays litManual Mode Auto Thermostatic ModeSafety Features ON/OFF Series Model GhrcbOperating Optional Blower Accessory Pilot AssemblyInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatCleaning and Maintenance Glass DoorPilot and Burners LogsTroubleshooting Observed Problem Possible CauseImproper vent configuration OrificeInlet gas pressure is too low CompanyGas leak. See Warning statement AboveSpecifications Wiring DiagramReplacement Parts Parts Under WarrantyIllustrated Parts Breakdown Model SdvbncParts List KEY Part Number DescriptionStove Chassis Models Csdbn and Csdpbn Stove Chassis KEY Part Number Csdbn Csdpbn Description QTYService Hints Technical ServiceAccessories Owners Registration Form Postage Required 111739-01A Warranty Information

CSDBN, CSDPBN specifications

Desa CSDPBN and CSDBN represent cutting-edge advancements in the realm of community-driven development and data-centric governance. These initiatives are designed to empower local communities by integrating technology with robust administration strategies to enhance public service delivery, economic development, and social welfare.

One of the main features of Desa CSDPBN is its focus on participatory governance, allowing community members to actively engage in decision-making processes. This framework encourages transparency and accountability, enabling citizens to voice their needs and priorities while fostering a sense of ownership over local projects. Such involvement helps create tailored solutions that effectively address the specific challenges faced by the community.

Technologically, Desa CSDPBN leverages an array of digital tools that facilitate real-time data collection and analysis. This includes geographic information systems (GIS) and mobile application development to gather insights on resource allocation, infrastructure needs, and demographic information. By employing data analytics, local governments can make informed decisions that enhance resource distribution and service delivery.

The characteristics of CSDPBN and CSDBN systems also extend to their adaptability and scalability. These frameworks are designed to be flexible, allowing them to be replicated across different regions with varying socio-economic contexts. This scalability ensures that diverse communities can benefit from the same foundational principles while customizing aspects to suit their unique environments.

Further enhancing their effectiveness, both initiatives incorporate capacity-building efforts aimed at training local leaders and stakeholders in the use of technology and project management. Such educational components empower communities to sustain development initiatives while fostering local expertise.

Additionally, the integration of social media and online platforms within the Desa CSDPBN framework promotes civic engagement and collaboration among community members. This connectivity nurtures a sense of unity and collective responsibility while improving communication between citizens and local authorities.

Ultimately, Desa CSDPBN and CSDBN embody a holistic approach to community development by harmonizing technology, governance, and citizen participation. They represent a transformative model that not only addresses immediate development needs but also lays the groundwork for sustainable growth and resilience in local communities. As these practices gain traction, they pave the way for a more equitable and inclusive future, where every voice contributes to the narrative of progress.
Top Page Image Contents