Desa CGEFP33NRB Installation, Continued, Installing Hood, Installing Logs, Burner, U-ShapedSlot

Page 21

Figure 39 - Attaching Brass Trim to Fireplace

INSTALLATION

Assembling And Attaching Optional Brass Trim (Cont.)

Installing Hood

Installing Logs

21

INSTALLATION

Continued

7.Repeat steps 1 through 6, page 20, for other side.

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim with hanging screws on side of fireplace (see Figure 39). Push trim firmly into place, sliding hanging notches over hanging screws.

Trim

Hanging

Screws

Hanging Notches on Trim

Assembled

Brass Trim

Figure 39 - Attaching Brass Trim to Fireplace

INSTALLING HOOD

Install hood to top of firebox as shown in Figure 40. Use 3 Phillips screws provided.

Figure 40 - Installing Hood to Firebox

INSTALLING LOGS

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: Do not remove the warning and in- struction labels attached to the heater base assem- bly. These markings contain important warranty in- formation.

CAUTION: After installation and periodically there- after, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs accord- ing to the log installation instructions in this manual. Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Locate pegs on the bottom of back log (#1). Slide these pegs into the holes in the grate base behind the burner (see Figure 41).

2.Place the base of the middle log (#2) in the U-shaped slots of the grate base in front of the back log. The cutout on the right of the middle log should fit over the burner (see Figure 42). Make sure the front of the middle log is resting on the tabs of the grate base and the cutout area is centered over the burner “U” bend.

Middle Log (#2)

	Back Log	Cutout
	Back Log
Hole in	(#1)
Hole in
Grate Base		Tab
		Tab
		Burner

Burner	“U” Bend
	U-Shaped Slot
Figure 41 - Installing Back	Figure 42 - Installing Middle
Log (#1)	Log (#2)

For morevisit www..com

111245-01A

Image 21

Contents UNVENTED VENT-FREEGAS FIREPLACE CGEFP33PRB, CGEFP33NRBGas Fireplace with Total Control System TCS TABLE OF CONTENTS SAFETY INFORMATIONWARNINGS PRODUCT IDENTIFICATION ContinuedSAFETY INFORMATION LOCAL CODES PRODUCT FEATURESUNPACKING SAFETY DEVICEPROVIDING ADEQUATE VENTILATION AIR FOR COMBUSTION AND VENTILATIONUnusually Tight Construction Confined Space and Unconfined SpaceContinued AIR FOR COMBUSTION AND VENTILATIONVentilation Air From Inside Building AIR FOR COMBUSTION AND VENTILATIONAIR FOR COMBUSTION AND VENTILATION INSTALLATIONContinued Ventilation Air From OutdoorsINSTALLATION CLEARANCES INSTALLATIONINSTALLATION SEQUENCE REMOVING FIREPLACE SCREEN AND FLOOR ASSEMBLYELECTRICAL CONNECTIONS FOR POWER CORD INSTALLATIONRELOCATING WALL SWITCH ASSEMBLY For Mantel InstallationFor Mantel Installation INSTALLATIONContinued CAUTION Do not apply excessive pull on cordINSTALLATION INSTALLING VARIABLE SPEED BLOWER ACCESSORYContinued INSTALLATION 8.Plug in blower power cordContinued INSTALLING THERMOSTATIC BLOWER ACCESSORY INSTALLATIONContinued Operating the BlowerINSTALLATION 12.Plug in blower power cordContinued INSTALLING GAS PIPING TO FIREPLACE LOCATION INSTALLATIONINSTALLATION ContinuedINSTALLATION Installation Items NeededContinued Installation Items Needed INSTALLATIONPressure Testing Gas Supply Piping System ContinuedPressure Testing Fireplace Gas Connections INSTALLATIONContinued necting Fireplace to Gas Supply, pageINSTALLATION BUILT-INFIREPLACE INSTALLATIONContinued Mantel Clearances for Built-InInstallation INSTALLATIONContinued Brass TrimINSTALLING HOOD INSTALLATIONINSTALLING LOGS INSTALLATIONINSTALLING BATTERY INTO REMOTE INSTALLATIONINSTALLING SCREEN INSTALLATIONFOR YOUR SAFETY READ BEFORE LIGHTING OPERATING FIREPLACEA. Using Supplied Wall Switch Assembly NORMAL LIGHTING INSTRUCTIONSShutting Off Heater - Wall Switch B. Using Hand-HeldWireless Remote ControlShutting Off Heater - Wireless Remote Control OPERATING FIREPLACEShutting Off Heater When Manually Lit INSPECTING BURNERSOPERATING FIREPLACE ContinuedCLEANING BURNER INJECTOR HOLDER CLEANING AND MAINTENANCECLEANING PILOT AIR INLET HOLE LOGSOBSERVED PROBLEM TROUBLESHOOTINGMaintenance, page POSSIBLE CAUSEOBSERVED PROBLEM TROUBLESHOOTINGContinued POSSIBLE CAUSEOBSERVED PROBLEM TROUBLESHOOTINGMaintenance, page ContinuedSERVICE HINTS SPECIFICATIONSTECHNICAL SERVICE REPLACEMENT PARTSWIRING DIAGRAM WIRING DIAGRAMBREAKDOWN ILLUSTRATED PARTSILLUSTRATED PARTS BREAKDOWN Models CGEFP33PRB and CGEFP33NRBPARTS LIST PARTS LISTPART NUMBER CGEFP33PRBILLUSTRATED PARTS BREAKDOWN ILLUSTRATED PARTS BREAKDOWNModels CGEFP33PRB and CGEFP33NRB 111245-01APARTS LIST PARTS LISTNot a field replaceable part PART NUMBERACCESSORIES 3/8 Diameter 2 Holes 3/4 TEMPLATES1/8 Diameter 2 Holes 3/4 4 3/4 3 3/4 3/8111245-01A THIS PAGE INTENTIONALLY LEFT BLANKOWNERS REGISTRATION FORM TAPE Postage RequiredTAPE 2701 Industrial Drive P.O. Box Bowling Green, KYLaportes Parts & Service PARTS CENTRALSBaltimore Electric Portable Heater Parts2701 Industrial Drive P.O. Box Bowling Green, KY NOT A UPC