Desa installation manual Installing Hood, Installing Logs CGEFP33NR

Page 18

UNVENTED NATURAL GAS FIREPLACE

INSTALLATION

Continued

ASSEMBLING AND ATTACHING OPTIONAL BRASS TRIM (Included with Mantel Accessory)

INote: The instructions below show assem- bling and attaching brass trim to fireplace.

1.Remove packaging from three pieces of brass trim.

2.Locate four brass screws, two adjust- ing plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 36.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 36).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 36).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim with hanging screws on side of fire- place (see Figure 37). Push trim firmly into place, sliding hanging notches over hanging screws.

Set Screws

Side Brass

Top

Brass

Trim

Trim

Adjusting

 

Plate

 

Trim

Hanging

Screws

Hanging Notches on Trim

Assembled

Brass Trim

Figure 37 - Attaching Brass Trim to Fireplace

INSTALLING HOOD

Install hood to top of firebox as shown in Figure 38. Use 3 Phillips screws provided.

Figure 38 - Installing Hood to Firebox

INSTALLING LOGS (CGEFP33NR)

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log. If so, reposition logs according to the

1.Locate pegs on the bottom of back log (#1). Slide these pegs into the holes in the grate base behind the burner (see Figure 39).

2.Place the base of the middle log (#2) in the U-shaped slots of the grate base in front of the back log. The cutout on the right of the middle log should fit over the burner (see Figure 40). Make sure the front of the middle log is resting on the tabs of the grate base and the cutout area is centered over the burner “U” bend.

3.Locate the recesses on the back of the front log (#3). Fit these recesses be- tween the posts of the grate base (see Figure 41, page 19).

Back Log

Hole in (#1)

Grate Base

Burner

Figure 39 - Installing Back Log (#1)

Middle Log (#2)

Tab

Burner

Cutout

“U” Bend

Slot

Shim

Slot

Mitered Edge

log installation instructions in this manual. Flames contacting logs will create soot.

U-Shaped Slot

Figure 36 - Assembling Brass Trim

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

Figure 40 - Installing Middle Log (#2)

For more information, visit www.desatech.com

18

107569

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASSafety Information Unvented Natural GAS FireplaceProduct Identification Local CodesUnpacking Product Features AIR for Combustion and VentilationAIR for Combustion Ventilation Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Building Ventilation AIRVentilation Air From Inside Ventilation Air From OutdoorsCheck GAS Type InstallationInstallation Clearances Electrical HookupInstallation Sequence Removal of Fireplace Screen and Floor AssemblyRelocating Wall Switch Lines and wiring when moving floor Installing Variable Speed Blower Accessory Mounting Wall Switch to Side of MantelInstalling Plastic Bushing for Power Cord Operating the BlowerInstalling Thermostatic Blower Accessory Lower Rear Wall Firebox BlowerInstalling Bushings Left Side Exit shown Installing GAS Piping to Fireplace Location Connecting Fireplace to GAS SupplyInstallation Items Needed Pressure Testing Fireplace Gas Connections Conventional Fireplace InstallationPressure Testing Gas Supply Piping System Checking GAS ConnectionsBUILT-IN Fireplace Installation Actual Framing Height 32 3/8 Front Width DepthMantel Clearances for Built-In Installation Nails or Wood ScrewsInstalling Hood Installing Logs CGEFP33NRInstalling Logs EFP33NR Middle Log #1 Shaped Cutout in Base BurnerFor Your Safety Read Before Lighting Installing ScreenInstalling Battery Into Remote Operating FireplaceShutting Off Heater Wall Switch Manual Lighting Instructions For Electrical Power OutageUsing Hand-Held Wireless Remote Control Shutting Off Heater Wireless Remote ControlOptional Blower Operation Shutting Off Heater When Manually LitInspecting Burners Pilot Flame PatternCleaning and Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleLogs Troubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement Wiring Diagram Service Hints SpecificationsReplacement Parts Technical ServiceParts Dealers Illustrated Parts Breakdown Parts List Remote Control Fireplace EFP33NR and CGEFP33NRFirebox KEY Part Number Description QTY Corner Mantel AccessoriesBlower Accessory GA3750 Series and GA3650T Series Equipment Shutoff Valve GA5010Diameter Holes This page Intentionally Left Blank 107569 Warranty Information

CGEFP33NR specifications

Desa CGEFP33NR is an innovative and efficient electrical appliance designed to cater to modern household needs. At the forefront of its offering is its exceptional energy efficiency, which allows it to provide substantial heating power while minimizing energy consumption. This model is equipped with advanced heating technologies that ensure quick and consistent warmth throughout any space it occupies.

One of the standout features of the Desa CGEFP33NR is its dual-fuel capability. This versatile appliance can operate on both natural gas and propane, making it a flexible choice for various residential settings. Users can easily switch between fuel types based on availability or preference, ensuring that they have a dependable heating source regardless of external conditions.

The unit also boasts an impressive heat output of up to 33,000 BTUs, which is suitable for heating spaces up to 1,500 square feet. This powerful heating capability is complemented by a built-in thermostat that allows for precise temperature control, ensuring that users can maintain their desired comfort level. The adjustable flame settings further enhance user control, letting individuals customize the heat output according to their specific requirements.

In terms of design, the Desa CGEFP33NR features a sleek and modern aesthetic that fits seamlessly into any home decor. Its compact size allows for easy installation, and it can be mounted on the wall or used as a freestanding unit, providing flexibility in placement. Safety is a top priority with this appliance, featuring built-in safety mechanisms such as an automatic shut-off system that activates in case of any irregularities.

The Desa CGEFP33NR is also equipped with a robust ignition system that ensures reliable start-up during operation. With its durable construction and high-quality materials, this unit is built to withstand the rigors of daily use while providing long-lasting performance.

In conclusion, the Desa CGEFP33NR is a remarkable heating solution that combines efficiency, versatility, and modern design. Its range of features, including dual-fuel capability, adjustable heat settings, and safety mechanisms, make it an ideal choice for homeowners looking to enhance their living spaces with effective and reliable heating solutions while also being energy-conscious.
Top Page Image Contents