Desa CGEFP33NR Installing Logs EFP33NR, Middle Log #1 Shaped Cutout in Base Burner

Page 19

OWNER’S MANUAL

INSTALLATION

Continued

4.Locate the notches in the bottom of the crossover log (#4). Place the crossover log on top of the middle log and front log. Make sure the notches of the cross- over log lines up with rectangular knobs on top of the middle and front logs (see Figure 42).

Front Log (#3)

Recess

Post

Post

Figure 41 - Installing Front Log (#3)

Crossover

Log (#4)

Rectangular

Knobs

Figure 42 - Installing Crossover Log (#4)

INSTALLING LOGS (EFP33NR)

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: Do not remove the warning and instruction labels attached to the heater base as- sembly. These markings contain important warranty information.

WARNING: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to High, check to see if flames contact any log. If so, re- position logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place the base of the middle log (#1) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Fig- ure 43). Make sure the front of the middle log is resting on the tabs of the grate base and the cutout area is cen- tered over the burner “U” bend.

2.Locate pegs on the bottom of back log (#2). Slide these pegs into the holes in the grate base behind the burner (see Figure 44).

3.Locate the notches in the bottom of the front log (#3). Place the front log on the grate fingers. Make sure the notches of the front log line up with the grate fingers (see Figure 45).

Middle Log (#1)

"U"-shaped Cutout in Base

Burner

Figure 43 - Installing Middle Log (#1)

4.Place crossover log (#4) onto the peg (right) on back log (#2) and into the re- cess of the middle log (#1) (see Figure 46).

Back Log (#2)

Peg

Peg

Figure 44 - Installing Back Log (#2)

Front Log (#3)

Notches

Grate Fingers

Figure 45 - Installing Front Log (#3)

Crossover Log (#4)

Peg

Recess

Figure 46 - Installing Crossover Log (#4)

Continued

107569

19

For more information, visit www.desatech.com

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualUnvented Natural GAS Fireplace Safety InformationLocal Codes Product IdentificationUnpacking AIR for Combustion and Ventilation Product FeaturesDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside BuildingElectrical Hookup InstallationInstallation Clearances Check GAS TypeRemoval of Fireplace Screen and Floor Assembly Installation SequenceRelocating Wall Switch Lines and wiring when moving floor Mounting Wall Switch to Side of Mantel Installing Variable Speed Blower AccessoryOperating the Blower Installing Plastic Bushing for Power CordLower Rear Wall Firebox Blower Installing Thermostatic Blower AccessoryInstalling Bushings Left Side Exit shown Connecting Fireplace to GAS Supply Installing GAS Piping to Fireplace LocationInstallation Items Needed Checking GAS Connections Conventional Fireplace InstallationPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsActual Framing Height 32 3/8 Front Width Depth BUILT-IN Fireplace InstallationNails or Wood Screws Mantel Clearances for Built-In InstallationInstalling Logs CGEFP33NR Installing HoodMiddle Log #1 Shaped Cutout in Base Burner Installing Logs EFP33NROperating Fireplace Installing ScreenInstalling Battery Into Remote For Your Safety Read Before LightingShutting Off Heater Wireless Remote Control Manual Lighting Instructions For Electrical Power OutageUsing Hand-Held Wireless Remote Control Shutting Off Heater Wall SwitchPilot Flame Pattern Shutting Off Heater When Manually LitInspecting Burners Optional Blower OperationCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning and MaintenanceLogs Observed Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Gas leak. See Warning statement Wiring Diagram Technical Service SpecificationsReplacement Parts Service HintsParts Dealers Illustrated Parts Breakdown Remote Control Fireplace EFP33NR and CGEFP33NR Parts ListFirebox KEY Part Number Description QTY Equipment Shutoff Valve GA5010 AccessoriesBlower Accessory GA3750 Series and GA3650T Series Corner MantelDiameter Holes This page Intentionally Left Blank 107569 Warranty Information

CGEFP33NR specifications

Desa CGEFP33NR is an innovative and efficient electrical appliance designed to cater to modern household needs. At the forefront of its offering is its exceptional energy efficiency, which allows it to provide substantial heating power while minimizing energy consumption. This model is equipped with advanced heating technologies that ensure quick and consistent warmth throughout any space it occupies.

One of the standout features of the Desa CGEFP33NR is its dual-fuel capability. This versatile appliance can operate on both natural gas and propane, making it a flexible choice for various residential settings. Users can easily switch between fuel types based on availability or preference, ensuring that they have a dependable heating source regardless of external conditions.

The unit also boasts an impressive heat output of up to 33,000 BTUs, which is suitable for heating spaces up to 1,500 square feet. This powerful heating capability is complemented by a built-in thermostat that allows for precise temperature control, ensuring that users can maintain their desired comfort level. The adjustable flame settings further enhance user control, letting individuals customize the heat output according to their specific requirements.

In terms of design, the Desa CGEFP33NR features a sleek and modern aesthetic that fits seamlessly into any home decor. Its compact size allows for easy installation, and it can be mounted on the wall or used as a freestanding unit, providing flexibility in placement. Safety is a top priority with this appliance, featuring built-in safety mechanisms such as an automatic shut-off system that activates in case of any irregularities.

The Desa CGEFP33NR is also equipped with a robust ignition system that ensures reliable start-up during operation. With its durable construction and high-quality materials, this unit is built to withstand the rigors of daily use while providing long-lasting performance.

In conclusion, the Desa CGEFP33NR is a remarkable heating solution that combines efficiency, versatility, and modern design. Its range of features, including dual-fuel capability, adjustable heat settings, and safety mechanisms, make it an ideal choice for homeowners looking to enhance their living spaces with effective and reliable heating solutions while also being energy-conscious.
Top Page Image Contents