Installation of Logs & Lava Rock, 10002428

Vermont Castings, Majestic Products DVRT36/39/43

Installation of Logs & Lava Rock

Unpack the logs from their shipping box. Remove each log from its wrapping material.

Dispose of the plastic bags and wrapping in a safe manner. Keep the logs and plastic bags away from children.

B43 Ceramic Ember Rocks

B32

B33

B31

B34

Take care handling the logs as the material is fragile. The individual logs can be identified by the number cast into the underside of each log.

DVRT36 - Refer to Figure 43.

1.Remove the top louvre assembly.

2.Remove the window frame assembly.

3.Fit the left-rear log (B43) to the left side of the rear log support. The two (2) holes in the log locate on the two (2) studs of the support.

4.Fit the right-rear log (B31) to the right side of the support. The two (2) holes in the log locate over the two (2) studs of the support.

5.Fit the left-front log (B32) to the support bracket over the burner housing. Again, the two (2) holes in the log locate on the two (2) studs on the bracket.

6.Place the left-top log (B33) across the left front and rear logs. (Fig. 43) The hole under the end of this log locates over the knob on the left rear log. The forward end of log B33 rests in the cutout in the left front log.

7.Place the right-front log (B34) in position by resting the ‘heal’ of the log between the outside and first prong of the front grate and laying the log down in the cutout of the right rear log. (Fig. 43)

8.Scatter the Ceramic Ember Rocks (Part #57897) over the burner housing assembly in the area forward of the front logs. Refer to shaded areas in Figure 43.

9.Scatter the lava rock (Part #10001454) around the base of the firebox area. Do not place any of this material on the burner housing assembly.

NOTE: Glowing lava rock for DVRT36 is only allowed to be positioned at the front area (radiant portion) of the burner housing assembly.

Do not mix the lava rock materials. Lava rock from the package labeled with Part #10001454 must not be placed on the burner housing assembly.

Front Grate tines

LG227

Fig. 43 DVRT36 logset and ember placement

DVRT39 - Refer to Figure 44.

1.Remove the top louvre assembly.

2.Remove the window frame assembly.

3.Fit the rear log (B35) onto the rear log support. The two (2) holes in the log locate on the two (2) studs on the support.

4.Fit the right-front log (B36) onto support bracket over the right side of the burner housing assembly. The two (2) holes in the log locate over the two (2) studs of the bracket.

5.Fit the left-front log (B37) onto the support bracket over the left side of the burner housing. Again, the two (2) holes in the log locate on the two (2) studs on the bracket.

6.Place the left-top log (B38) in place. The notch along the lower front edge sits against the front grate (Fig. 44), and the top of the log sits in the cutout on the inner end of log B37.

7.Scatter the Ceramic Ember Rocks (Part #57897) over the burner housing assembly in the areas between the logs. Refer to shaded areas in Figure 44.

8.Scatter the lava rock (Part #10001454) around the base of the firebox area. Do not place any of this material on the burner housing assembly.

NOTE: Glowing lava rock for DVRT39 is only allowed to be positioned at the front area (radiant portion) of the burner housing assembly.

Do not mix the lava rock materials. Lava rock from the package labeled with Part #10001454 must not be placed on the burner housing assembly.

10002428