Ceiling Clearances

Clearance Requirements

Minimum Clearances to Combustible

Materials

Measure side clearances as shown in Figures 2 through 5 from the outer edge of the cast iron stove top. Measure rear clearances from the outermost surface of the sheet metal rear skirt.

The Dutchwest heater is approved for installation into an alcove constructed of combustible materials to the dimensions and clearances shown in Figure 5.

The same clearances apply in a standard parallel installation.

Parallel Installation: Minimum Clearance

and Flue Centerline

		C
		L
		C
	D	A
	D
	C
	L
	B
Stove Clearances		A: 5” (125mm)
		B: 4” (102mm)
Pipe Centerlines		C: 16” (406mm)
		D: 9¹⁄₄” (235mm)	ST128c
Fig. 2	Parallel installation requirements.

Corner Installation: Minimum Clearance and Flue Centerline

	B
		A
B
A
Stove Clearance	A: 4” (102mm)
Pipe Centerline	B: 17” (432mm)	ST129c

Fig. 3 Corner installation requirements.

Dutchwest Natural Vent Gas Heater

45"

(1140mm)

72"

(1829mm)

ST774

Fig. 4 Minimum ceiling clearance; minimum alcove height.

Alcove Minimum Dimensions

		C
A		A
	B
A: 4” (102mm)	B: 33” (838mm)	C: 5” (125mm)
		ST775

Fig. 5 The Dutchwest Natural Vent Stove is approved for installation into alcoves built of combustible materials.

Hearth Requirements

The Dutchwest Heater must be installed on rigid flooring. When the heater is installed directly on any combustible surface other than wood flooring, a metal or wood panel extending the full width and depth of the unit must be used as the hearth. There are no other hearth requirements.

WARNING:

• Always maintain required clearances (air spaces) to nearby combustibles to prevent fire hazard. Do not fill air spaces with insulation. All venting components must maintain a 1" (25mm) clearance to combustible materials. Maintain a 6” (150mm) clearance when using single wall pipe.

•The gas appliance and vent system must be vented directly to the outside of the building and never be attached to a chimney serving a separate solid fuel or gas-burning appliance.

•Refer to the manufacturer's instructions included with the venting system for complete installation procedures.

30002008

2468, 2467, 2468 specifications

CFM Corporation has established itself as a powerhouse in the aviation industry, particularly through the design and manufacture of high-performance aircraft engines. Among its standout products are the CFM 2468 and 2467 engines, which have garnered attention for their state-of-the-art features, innovative technologies, and impressive performance characteristics.

The CFM 2468 engine is known for its remarkable efficiency and reliability. One of its primary features is the advanced fuel efficiency technology that minimizes fuel consumption while maximizing thrust. This is largely attributed to the inclusion of next-generation composites in the engine's fan blades and cases, which contribute to a lighter overall weight without compromising durability. As a result, operators benefit from lower operating costs, making the 2468 engine a cost-effective choice for airlines.

On the other hand, the CFM 2467 engine has been engineered with a focus on reducing noise pollution and emissions. This engine incorporates cutting-edge noise-reducing technologies, including a redesigned inlet and an innovative exhaust system that reduces noise levels significantly during operation. This makes the 2467 an ideal solution for airports in urban areas where noise regulations are stringent. Furthermore, the engine's environmentally friendly design complies with the latest emissions standards, which is increasingly important in today's aviation market.

Both engines utilize advanced digital technologies, including the latest in engine health monitoring systems. These systems provide real-time data analytics to operators, allowing for predictive maintenance and minimizing downtime. This technological integration not only enhances operational efficiency but also helps in extending the lifespan of the engines.

In terms of operational characteristics, both the CFM 2468 and 2467 engines are built to perform under a wide range of conditions. Their robust design ensures they can withstand various environmental challenges, from extreme temperatures to high humidity. Additionally, their modular design simplifies maintenance procedures, allowing for quicker turnaround times.

In summary, the CFM Corporation 2468 and 2467 engines exemplify the company's commitment to innovation, efficiency, and sustainability. With their advanced technologies and impressive features, these engines are set to redefine performance standards in the aviation industry, making them a preferred choice for airlines globally.