Regency C34-LP2, C34-NG2 installation manual DV Stove Horizontal Vent KIT, Optional

Page 15

INSTALLATION

DV STOVE HORIZONTAL VENT KIT

DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (946-216) include all the parts needed to install the C34 with minimum horizontal and vertical vent dimensions. For installations that require longer vertical and/or horizontal vents use the Dura-Vent system as shown on page 17.

Qty. Description

1)1 Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,

Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm) inside diameter

2)1 Flex Liner, compressed aluminium 2 ply liner, 4" (102mm) inside diameter

3)4 spring spacers

4)1 90 deg. Elbow

5)1 Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 pieces

6)1 Thimble Cover

7)1 Wall Thimble (2 pcs.)

8)1 Adapter

9)1 AstroCap Termination Cap

10)2 Trim Collar

11)1 tube of Mill-Pac, high temperature sealant

12)12 Screws, #8 x 1/2" Self tapping, Stainless Steel

13)14 Screws, #8 x 1/2" Self tapping, Black

14)4 Screws #8 x 1-1/2" Drill Point, Black

15)4 Screws #8 x 1-1/2" Drill Point, Stainless Steel

16)8 Wood screws #8 x 1"

Optional:

946-206 Vinyl Siding Standoff

for AstroCap

Note:

a)Liner sections should be continuous without any joints or seams.

b)This is an approved system, therefore components in this system must not be substituted for any other manufacturer's products.

DV STOVE HORIZONTAL VENT KIT (#946-116 & #946-216) INSTALLATION

Review the following sequence of instructions which are typical of most installations. The sequence may vary depending on wall thick- ness.

Refer to pages 6 to 10 for vent location and clearance dimensions.

1)Set the unit in its desired location. Check to determine if wall studs will be in the way of the venting system, adjust location until all clearances are met and there are no ob- structions.

Note: A 1-1/2"(38mm) clearance around the outer pipe must be maintained except that only a 1" (25mm) clear- ance is needed at the termination end.

IMPORTANT:

Do not locate termination hood where excessive snow or ice buildup may oc- cur. Be sure to check vent termination area after snow falls, and clear to pre- vent accidental blockage of venting sys- tem. When using snow blowers, make

sure snow is not directed towards vent termination area.

2)Assemble a trial fit to determine the vertical center-line for the vent termina- tion.

a)Cut a 9-1/2" x 9-1/2" (241mm x 241 mm) square hole on both the interior and exterior wall.

b)Install wall thimbles on both interior andexteriorwallwith4woodscrews (#8 x 1") per thimble.

c)Attach the 2 piece adjustable pipe section to the vent terminal and slide into position from the exterior. The larger diameter end of the ad- justable pipe goes to the vent terminal.

d)Install the 90o elbow onto the adjust- able pipe to determine the vertical centerline of the starter collar on the unit.

Note: if the centerline cannot be met, the adjustable sections will have to be cut.

Regency CLASSIC C34-2 Direct Vent Freestanding Gas Heater

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents C34 Classic Direct Vent Freestanding Gas Stove Classic Direct Vent Freestanding Gas Stove To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Save These Instructions InstallationSpecifications General Safety InformationInstallation Checklist Locating Your Classic GAS StoveCombustion and Ventilation AIR Disconnect power supply Before servicing Optional FAN InstallationPedestal Assembly LEG and Bottom Shield AssemblyFan Removal Safety Precautions for the Installer InstallationExterior Vent Terminal Locations 4DT-AJB Rigid Pipe Venting Components ListAlternate Horizontal Termination Caps Rigid Pipe Venting SystemsVenting Arrangements Examples Vertical Venting with Two 2 90o Elbows Horizontal Venting with Two 2 90o ElbowsOptional DV Stove Horizontal Vent KITOut a square that the cap can be mounted on Description Planning Your Dura-Vent InstallationDURA-VENT Termination KIT DURA-VENT Venting ComponentsDura-Vent Basic Horizontal Kit # DURA-VENT Horizontal Installations Below Grade InstallationSnorkel Terminations Vertical Termination Offset Chart Cathedral CeilingsRound Support RDS & Square Support SQS Regency Classic C34-2 Direct Vent Freestanding Gas Heater Support extensions Round Rdse or square SqseGeneral Converting a Factory Built Metal ChimneyConverting a Masonry Chimney High Elevation GAS Pipe Pressure TestingSystem Data GAS ConnectionFrame LOG InstallationDoor Handle Option 2 Remote Wall SwitchOption 1 Remote Control Installation Option 3 Wall Thermostat InstallationWiring Diagram Operating Instructions Copy of the Lighting Plate Instructions Aeration AdjustmentMaintenance GOLD-PLATED Doors Glass ReplacementInstalling Valve Assembly Removing Valve AssemblyMain Assembly Parts ListBurner Assembly & LOG SET Base Options Conditions WarrantyInstaller Please complete the following information

C34-LP2, C34-NG2 specifications

The Regency C34-LP2 and C34-NG2 are two exceptional offerings in the world of gas fireplaces, designed to bring both warmth and style to modern living spaces. These units are perfect for homeowners who appreciate the ambiance of a traditional fireplace but desire the convenience and efficiency of gas heating.

Starting with the design, both the C34-LP2 and C34-NG2 feature a sleek and contemporary aesthetic, easily integrating into various interior styles. The clean lines and large viewing area provide an unobstructed view of the flames, creating a focal point in any room. The glass front complements the modern decor while emphasizing the natural flicker of firelight.

One of the standout features of the C34 series is the dual burner system, which allows for enhanced flame control and efficiency. The design offers an impressive flame pattern that can be adjusted to suit the user's preference, whether they seek a cozy, intimate setting or a more robust fire experience. This versatility is especially appealing for entertaining guests or creating a romantic atmosphere at home.

Technologically, both models are equipped with advanced features to optimize performance. The electronic ignition system ensures reliable lighting, while the precision flame adjustment allows users to easily manipulate heat levels. This adaptability can lead to significant energy savings, making the C34 series not only environmentally conscious but also cost-effective.

In terms of technical specifications, the C34-LP2 is designed for liquid propane, while the C34-NG2 runs on natural gas, providing flexibility depending on the homeowner's fuel availability. Both models possess impressive heating capabilities, with an output sufficient to warm larger spaces, making them ideal for living rooms, dining areas, or open-concept homes.

Safety is also a priority with the C34 series. Equipped with a safety shutoff system and a glass front that remains cool to the touch, these units are designed to provide peace of mind for families. The option for a remote control adds an additional layer of convenience, allowing users to adjust settings from across the room.

Overall, the Regency C34-LP2 and C34-NG2 unite modern innovation with traditional comfort. With their stunning design, advanced technology, and excellent heating efficiency, these gas fireplaces are a valuable addition to any home, enhancing both aesthetic and functional appeal.
Top Page Image Contents