Regency C34-NG2, C34-LP2 Pedestal Assembly, LEG and Bottom Shield Assembly, Fan Removal

Page 8

INSTALLATION

10)Put the insulation gasket on the back of the fan. Line up the keyhole slots with the matching screws and pull back slightly to lock into place. While holding fan assembly in place, tighten screws.

11)Remove the dummy plug from the right side of the bottom shield or pedestal and install the supplied fan switch.

12)Attach the hot wire from power cord to the thermodisc.

13)Slide thermodisc under the thermodisc brack- et.

14)Connecting wires to the 3 way switch:

a.Connect the red wire from the fan to the top of the 3 way switch.

b.Connect black wire from fan to the bottom of the 3 way switch.

c.Connect white jumper wire to middle of the three way switch. See wiring dia- gram below.

15)Connect white wire from fan motor to neu- tral on the power cord.

16)Pull power wire back and put strain relief grommet in place as per diagram 4.

17)Reverse steps 3-1 to complete installation.

Fan Removal

PEDESTAL ASSEMBLY

1)For easier assembly, tip the stove on its back (preferably onto a soft surface to prevent scratching).

2)Unscrew the 4 bolts in the underside of the stove. Align the holes in the corners of the pedestal top with the corresponding holes in the base of the stove. Use washers which are supplied with the pedestal as shown in diagram. Reinstall bolts.

LEG AND BOTTOM SHIELD ASSEMBLY

These instructions apply to the steel leg, painted cast leg and the gold plated cast leg. It will be easier to attach the legs to the stove if it is tipped on its back (preferably on a soft surface to prevent scratching).

1)Remove the 4 bolts in the underside of the base and discard.

2)Slide the bolt and washer (supplied with the bottom shield) through the leg, then slide the bottom shield in between the leg and the base of the stove. Tighten the bolts.

3)Hook up the Burner ON/OFF switch.

4)Level the stove by adjusting the levelling bolts in the bottom of each leg.

1)Disconnect the power to the fan.

2)Allow the stove to cool to room temperature.

3)Open the pedestal door and remove the screws on the door cover plate. (Leg units: remove the bottom access panel.)

4)Loosen the screws of the nutserts.

5)Remove the fan assembly from the key slots at the fan base and pull fan out through the rectangular opening. (Diagram 3).

6)Turn fan 90 degrees. (Diagram 2). (Pedestal units only).

7)Disconnect the green ground wires to the grounding lug.

8)Disconnect the white wire of the fan from the power cord.

9)Disconnect the red wire and black wire (from fan to Fan Switch).

10)Take fan out from the stove body. (Diagram 1).

3)Hook up wires to Burner ON/OFF switch and valve assembly (be careful not to pinch wires). See diagram above.

4)Push the Regency logo into the two holes in the front bottom left corner of the pedes- tal cover plate.

Note: Any paint touch up should be done prior to placing logo on pedestal.

Anchoring Brackets Hold DownPackagePart#846-585

8

Regency CLASSIC C34-2 Direct Vent Freestanding Gas Heater

Image 8
Contents C34 Classic Direct Vent Freestanding Gas Stove Information for MOBILE/MANUFACTURED Homes After First Sale Classic Direct Vent Freestanding Gas Stove To the New OwnerTable of Contents Safety Label Installation SpecificationsGeneral Safety Information Save These InstructionsCombustion and Ventilation AIR Installation ChecklistLocating Your Classic GAS Stove Optional FAN Installation Disconnect power supply Before servicingFan Removal Pedestal AssemblyLEG and Bottom Shield Assembly Installation Safety Precautions for the InstallerExterior Vent Terminal Locations Rigid Pipe Venting Components List 4DT-AJBRigid Pipe Venting Systems Alternate Horizontal Termination CapsVenting Arrangements Examples Horizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o ElbowsDV Stove Horizontal Vent KIT OptionalOut a square that the cap can be mounted on Planning Your Dura-Vent Installation DURA-VENT Termination KITDURA-VENT Venting Components DescriptionDura-Vent Basic Horizontal Kit # Snorkel Terminations DURA-VENT Horizontal InstallationsBelow Grade Installation Vertical Termination Round Support RDS & Square Support SQS Offset ChartCathedral Ceilings Support extensions Round Rdse or square Sqse GeneralConverting a Factory Built Metal Chimney Regency Classic C34-2 Direct Vent Freestanding Gas HeaterConverting a Masonry Chimney GAS Pipe Pressure Testing System DataGAS Connection High ElevationLOG Installation FrameOption 2 Remote Wall Switch Option 1 Remote Control InstallationOption 3 Wall Thermostat Installation Door HandleWiring Diagram Operating Instructions Aeration Adjustment Copy of the Lighting Plate InstructionsMaintenance Glass Replacement Installing Valve AssemblyRemoving Valve Assembly GOLD-PLATED DoorsParts List Main AssemblyBurner Assembly & LOG SET Base Options Warranty ConditionsInstaller Please complete the following information

C34-LP2, C34-NG2 specifications

The Regency C34-LP2 and C34-NG2 are two exceptional offerings in the world of gas fireplaces, designed to bring both warmth and style to modern living spaces. These units are perfect for homeowners who appreciate the ambiance of a traditional fireplace but desire the convenience and efficiency of gas heating.

Starting with the design, both the C34-LP2 and C34-NG2 feature a sleek and contemporary aesthetic, easily integrating into various interior styles. The clean lines and large viewing area provide an unobstructed view of the flames, creating a focal point in any room. The glass front complements the modern decor while emphasizing the natural flicker of firelight.

One of the standout features of the C34 series is the dual burner system, which allows for enhanced flame control and efficiency. The design offers an impressive flame pattern that can be adjusted to suit the user's preference, whether they seek a cozy, intimate setting or a more robust fire experience. This versatility is especially appealing for entertaining guests or creating a romantic atmosphere at home.

Technologically, both models are equipped with advanced features to optimize performance. The electronic ignition system ensures reliable lighting, while the precision flame adjustment allows users to easily manipulate heat levels. This adaptability can lead to significant energy savings, making the C34 series not only environmentally conscious but also cost-effective.

In terms of technical specifications, the C34-LP2 is designed for liquid propane, while the C34-NG2 runs on natural gas, providing flexibility depending on the homeowner's fuel availability. Both models possess impressive heating capabilities, with an output sufficient to warm larger spaces, making them ideal for living rooms, dining areas, or open-concept homes.

Safety is also a priority with the C34 series. Equipped with a safety shutoff system and a glass front that remains cool to the touch, these units are designed to provide peace of mind for families. The option for a remote control adds an additional layer of convenience, allowing users to adjust settings from across the room.

Overall, the Regency C34-LP2 and C34-NG2 unite modern innovation with traditional comfort. With their stunning design, advanced technology, and excellent heating efficiency, these gas fireplaces are a valuable addition to any home, enhancing both aesthetic and functional appeal.