Regency P40 Conversion KIT #502-969 from NG to LP, LP Conversion Kit Contains Qty Description

Page 26

INSTALLATION

INSTALLATION

CONVERSION KIT #502-969 FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

LP Conversion Kit Contains:

Qty.

Part #

Description

1

910-462

LP Conversion Coil

1

910-037

LP Pilot Orifice

1

904-345

Orifice #53

1

904-575

Orifice #55

1

904-529

Allen Key

1

918-590

LP Conversion Decal

1

908-528

Red Propane Label

6)Slide the burner to the right and lift out. 11) Remove the clip from the pilot head assembly using a flat head screw driver to pop out.

7)Remove the front burner by removing the 2 screws. Lift the burner up and swing to the right and slide out.

1918-587 Instruction Sheet

1)Turn control knob to the OFF position; Shut off the gas supply to the valve; Unplug the power source.

2)Remove the louvers and the flush door.

3)Remove the logs.

4)Remove the front air box by undoing the 3 screws.

Front Air Box

Front Burner

8)Replace the rear burner orifice with #53, using a 1/2" wrench. See image below. Use another wrench to hold onto the elbow behind the orifice.

9)Replace the front burner orifice with #55, using a 1/2" wrench. See image below. Use another wrench to hold onto the elbow behind the orifice.

Clip

12)Remove the NG pilot orifice with the Allen Key and replace with LP pilot orifice. Reattach pilot head and clip.

Rear Burner

Front Burner

5)Remove the 2 screws on the back burner.

Orifi ce

Orifi ce

13)

Re-install pilot shield.

14)

Set aeration on both front and rear burner

Back Burner

10)Remove the pilot shield by removing the 2 screws.

Pilot Shield

 

for LP gas;

 

 

Rear

5/16"

 

Front

3/8"

15)

Reverse steps 7 to 4.

16)

Remove the Power Module by lifting it up off

 

of the velcro and move it over to the side.

Power Module

26

Regency® P40 Direct Vent Gas Fireplace

Image 26
Contents P40 Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Copy of Safety LabelRequirements MA Code CO DetectorUnit Dimensions Installation Checklist InstallationGeneral Safety Information Important Message Save These InstructionsHearth Requirements Manufactured Mobile Home Additional RequirementsHeat Release KIT Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesFraming & Finishing Height = 42-1/2 plus height of hearthVent Restrictor Position Unit Assembly Prior to InstallationVenting Introduction ScrewInstallation Exterior Vent Termination RequirementsVenting Arrangements Horizontal Termination FlexRigid Pipe Venting Systems Basic Horizontal & Vertical TerminationsRigid Pipe Venting Components List Rigid Pipe Adaptor Must use with all Rigid PipingAllowable Horizontal Terminations Vertical Height FeetHorizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Allowable Vertical Terminations Vent must be supported at offsetsUnit Installation with Horizontal Termination Arrow on the vent cap should be pointing upDiagram Unit Installation With Vertical TerminationThis allows for small adjustments Minimum VentUnit Installation Astrocap XL DimensionsHigh Elevation GAS Line InstallationPilot Adjustment P40-NG System DataUnplug the power source GAS Pipe Pressure TestingBACK-UP Battery Installation Power ModuleConversion KIT #502-969 from NG to LP LP Conversion Kit Contains Qty DescriptionControl Module Top Brick Panel Brick Panel InstallationEnsure that the logs are not in the unit Back Brick PanelLOG SET Installation Ember BedEmber Bed Completed Log Set Installation Standard Flush Door Aeration AdjustmentInstalling the Manual Control Box Flush LouversDo not cut the ground terminal off under any circumstances Wiring DiagramFinishing Trim Operating Instructions Lightingshutdown Procedure ProcedureOperating Instructions First FireSummary Controls Operation During Power OutageFirewizardtm Remote Control Functions Normal Operating Sounds GAS Appliances Copy Lighting Plate InstructionsMaintenance FAN Replacement Control ModuleBack Burner Valve ReplacementFender Solenoid Valve Front Air BoxDC Sparker Replacement Backup Battery Replacement Power Module ReplacementControl Module Replacement Heat ShieldDescription Parts ListMain Assembly Valve Tray Assembly Flush Door & Louvers Regency P40 Direct Vent Gas Fireplace Regency P40 Direct Vent Gas Fireplace Warranty Warranty Limited LifetimeInstaller Please complete the following information

P40, P40-LP, P40-NG specifications

The Regency P40 series, comprising the P40-LP, P40, and P40-NG models, represents a significant advancement in the world of portable radio communications. Designed with both versatility and performance in mind, these devices cater to a diverse range of users, from public safety professionals to outdoor enthusiasts.

One of the standout features of the P40 series is its robust build quality. The radios are engineered to withstand harsh environments, boasting IP67 water and dust resistance ratings. This ensures reliable performance even in challenging conditions, making them ideal for emergency responders who operate in adverse weather or rugged terrains. The P40's durable design is complemented by a lightweight construction, allowing for prolonged use without fatigue.

The P40 series is equipped with advanced digital technology that enhances both audio clarity and range. With a powerful speaker and noise-canceling capabilities, users can communicate clearly even in noisy surroundings. The P40-NG model takes this a step further by incorporating digital signal processing (DSP) technology, which optimizes sound for both transmission and reception.

Battery life is a critical aspect of any portable device, and the P40 series excels in this regard. With options for high-capacity lithium-ion batteries, users can expect extended operational times, vital for those on long shifts or field operations. Additionally, the smart battery management system provides real-time battery status updates, ensuring users are never caught off guard.

Interoperability is another key characteristic of the P40 series. The radios support multiple frequency bands and can seamlessly integrate with existing communication infrastructures. This capability is particularly beneficial for agencies that require coordination across various channels and networks.

User-friendly interfaces define the P40 series, with intuitive controls and customizable features. The color display on the P40 and P40-NG models enhances usability, allowing for easy navigation through settings and features. Furthermore, programmable buttons facilitate quick access to frequently used functions, ensuring efficient communication even in high-pressure scenarios.

Overall, the Regency P40-LP, P40, and P40-NG radios embody reliability, advanced technology, and ruggedness, making them essential tools for effective communication in a variety of demanding environments. With their combination of durability, audio performance, and battery life, these radios stand out as a top choice for both professional and recreational use.