Regency P40-NG, P40-LP Aeration Adjustment, Standard Flush Door, Flush Louvers

Page 32

INSTALLATION

INSTALLATION

AERATION

ADJUSTMENT

Aeration Adjustment should only be per- formed by an authorized Regency® Installer at the time of installation or service.

The rear burner aeration is factory set but may need adjusting due to either the local gas supply or altitude.

The rear burner air shutter can be adjusted by moving the air shutter wire. Open (pull) the air shutter wire for a blue fl ame or close (push) for a more yellow fl ame.

*The front burner aeration is factory set, do not adjust this setting.

Minimum Air Shutter Opening:

NG

Front Burner*

1/8"

 

Rear Burner

1/4"

LP

Front Burner*

3/8"

 

Rear Burner

5/16"

CAUTION: Carbon will be produced if air shutter is closed too much.

STANDARD

FLUSH DOOR

NOTE: Install Finishing Trim prior to installing the Flush Door and Louvers.

1)The standard fl ush door comes with a black frame. To install the frame, simply hook the top door fl ange onto the top of the unit and swing the door towards the unit, diagram 1.

FLUSH LOUVERS

NOTE: Install Finishing Trim prior to installing the Flush Door and Louvers.

1)Install the top louver by sliding the two bracket clips into the brackets located underneath the top of the fi rebox.

2)Install the bottom louver by securing the louver onto the 2 hinges provided.

Note: Top and Bottom Louvers are different.

Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.

Rear Burner

Adjustment Wire

Diagram 1

2)Be careful that the glass gasket does not roll up; there must be a gap between the gasket and the door lip to ensure that the door sits securely on the unit. Diagram 2.

3) Installing the Manual Control Box

a)Ensure that the bottom louver is open.

b)Pull out the Manual Control Box from the right side under the bottom of the fi rebox.

c)Using the 2 screws on the louver, secure the control box onto the right side of the louver.

Adjustment Wire - Pull to open or

push to close aeration cap.

Diagram 2

3)Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket. Repeat for 2nd spring. See diagram 3.

Manual Control Box

Diagram 3

NOTE: Springs and chain must always be OVER not under the gas line.

4)To remove the fl ush door, reverse the above steps.

32

Regency® P40 Direct Vent Gas Fireplace

Page 31 Page 33
Image 32
Page 31 Page 33
Contents P40 Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Copy of Safety LabelRequirements MA Code CO DetectorUnit Dimensions Installation General Safety InformationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Heat Release KITHearth Requirements Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesFraming & Finishing Height = 42-1/2 plus height of hearthUnit Assembly Prior to Installation Venting IntroductionVent Restrictor Position ScrewInstallation Exterior Vent Termination RequirementsVenting Arrangements Horizontal Termination FlexRigid Pipe Venting Systems Basic Horizontal & Vertical TerminationsRigid Pipe Venting Components List Rigid Pipe Adaptor Must use with all Rigid PipingAllowable Horizontal Terminations Vertical Height FeetHorizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Allowable Vertical Terminations Vent must be supported at offsetsUnit Installation with Horizontal Termination Arrow on the vent cap should be pointing upUnit Installation With Vertical Termination This allows for small adjustmentsDiagram Minimum VentUnit Installation Astrocap XL DimensionsGAS Line Installation Pilot AdjustmentHigh Elevation P40-NG System DataGAS Pipe Pressure Testing BACK-UP Battery InstallationUnplug the power source Power ModuleConversion KIT #502-969 from NG to LP LP Conversion Kit Contains Qty DescriptionControl Module Brick Panel Installation Ensure that the logs are not in the unitTop Brick Panel Back Brick PanelLOG SET Installation Ember BedEmber Bed Completed Log Set Installation Aeration Adjustment Installing the Manual Control BoxStandard Flush Door Flush LouversDo not cut the ground terminal off under any circumstances Wiring DiagramFinishing Trim Lightingshutdown Procedure Procedure Operating InstructionsOperating Instructions First FireSummary Controls Operation During Power OutageFirewizardtm Remote Control Functions Normal Operating Sounds GAS Appliances Copy Lighting Plate InstructionsMaintenance FAN Replacement Control ModuleValve Replacement FenderBack Burner Solenoid Valve Front Air BoxDC Sparker Replacement Power Module Replacement Control Module ReplacementBackup Battery Replacement Heat ShieldDescription Parts ListMain Assembly Valve Tray Assembly Flush Door & Louvers Regency P40 Direct Vent Gas Fireplace Regency P40 Direct Vent Gas Fireplace Warranty Warranty Limited LifetimeInstaller Please complete the following information

P40, P40-LP, P40-NG specifications

The Regency P40 series, comprising the P40-LP, P40, and P40-NG models, represents a significant advancement in the world of portable radio communications. Designed with both versatility and performance in mind, these devices cater to a diverse range of users, from public safety professionals to outdoor enthusiasts.

One of the standout features of the P40 series is its robust build quality. The radios are engineered to withstand harsh environments, boasting IP67 water and dust resistance ratings. This ensures reliable performance even in challenging conditions, making them ideal for emergency responders who operate in adverse weather or rugged terrains. The P40's durable design is complemented by a lightweight construction, allowing for prolonged use without fatigue.

The P40 series is equipped with advanced digital technology that enhances both audio clarity and range. With a powerful speaker and noise-canceling capabilities, users can communicate clearly even in noisy surroundings. The P40-NG model takes this a step further by incorporating digital signal processing (DSP) technology, which optimizes sound for both transmission and reception.

Battery life is a critical aspect of any portable device, and the P40 series excels in this regard. With options for high-capacity lithium-ion batteries, users can expect extended operational times, vital for those on long shifts or field operations. Additionally, the smart battery management system provides real-time battery status updates, ensuring users are never caught off guard.

Interoperability is another key characteristic of the P40 series. The radios support multiple frequency bands and can seamlessly integrate with existing communication infrastructures. This capability is particularly beneficial for agencies that require coordination across various channels and networks.

User-friendly interfaces define the P40 series, with intuitive controls and customizable features. The color display on the P40 and P40-NG models enhances usability, allowing for easy navigation through settings and features. Furthermore, programmable buttons facilitate quick access to frequently used functions, ensuring efficient communication even in high-pressure scenarios.

Overall, the Regency P40-LP, P40, and P40-NG radios embody reliability, advanced technology, and ruggedness, making them essential tools for effective communication in a variety of demanding environments. With their combination of durability, audio performance, and battery life, these radios stand out as a top choice for both professional and recreational use.
Top Page Image Contents