Regency P40-NG, P40-LP installation manual Control Module

Page 27

INSTALLATION

17)Remove the Control Module, located behind the power module, by lifting it up off of the velcro.

Control Module

18)Remove the J9 jumper using needle nose pliers, located under the heat shield.

J9 Jumper

19)Reverse steps 17 and 16. Be careful not to pinch wires.

20)Remove the 2 wires connected to the modulating coil.

Modulating Coil

21)Using a Torx T20, or slotted screwdriver, remove and discard the three pressure regulator mounting screws and rubber diaphram.

22)Insure that the new rubber gasket is properly positioned and install the new modulating pressure regulator assembly to the valve using the screws supplied with the kit. Tighten screws securely.

23)Reattach 2 wires to modulating coil.

24)Install the enclosed identification label to the valve body where it can be easily seen. The label is found in the coil pack- age.

25)Attach the LP conversion decal near or on top of the serial # decal located on a metal plate under the unit.

26)Replace the yellow "Natural Gas" label with the red "Propane" label on the valve assembly.

27)Ensure proper installation of venting is complete, gas line is connected and then turn on power to unit.

28)Check for gas leaks.

29)Check inlet (12" wc) and outlet (10" wc) pressures.

30)Check operation of flame control using the manual control box located on the right side under the firebox.

31)Re-install logs and flush door. Check for proper flame appearance and glow on logs.

WARNING!

This conversion kit should be installed by a qualified service agency in ac- cordance with the authority having jurisdiction. If the information in these instructions are not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is respon- sible for the proper installation of this kit. The installation is not proper and complete until the operation of the con- verted appliance is checked as speci- fied in the manufacturer's instructions supplied with the kit.

Installer Notice:

These instructions must be left

with the appliance.

INSTALLATION

Regency® P40 Direct Vent Gas Fireplace

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents P40 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Label Safety LabelMA Code CO Detector RequirementsUnit Dimensions Important Message Save These Instructions InstallationGeneral Safety Information Installation ChecklistLocating Your GAS Fireplace Manufactured Mobile Home Additional RequirementsHeat Release KIT Hearth RequirementsClearances Mantel LEG Clearances Mantel ClearancesHeight = 42-1/2 plus height of hearth Framing & FinishingScrew Unit Assembly Prior to InstallationVenting Introduction Vent Restrictor PositionExterior Vent Termination Requirements InstallationHorizontal Termination Flex Venting ArrangementsBasic Horizontal & Vertical Terminations Rigid Pipe Venting SystemsRigid Pipe Adaptor Must use with all Rigid Piping Rigid Pipe Venting Components ListVertical Height Feet Allowable Horizontal TerminationsHorizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Vent must be supported at offsets Allowable Vertical TerminationsArrow on the vent cap should be pointing up Unit Installation with Horizontal TerminationMinimum Vent Unit Installation With Vertical TerminationThis allows for small adjustments DiagramAstrocap XL Dimensions Unit InstallationP40-NG System Data GAS Line InstallationPilot Adjustment High ElevationPower Module GAS Pipe Pressure TestingBACK-UP Battery Installation Unplug the power sourceLP Conversion Kit Contains Qty Description Conversion KIT #502-969 from NG to LPControl Module Back Brick Panel Brick Panel InstallationEnsure that the logs are not in the unit Top Brick PanelEmber Bed LOG SET InstallationEmber Bed Completed Log Set Installation Flush Louvers Aeration AdjustmentInstalling the Manual Control Box Standard Flush DoorWiring Diagram Finishing TrimDo not cut the ground terminal off under any circumstances First Fire Lightingshutdown Procedure ProcedureOperating Instructions Operating InstructionsOperation During Power Outage Firewizardtm Remote Control FunctionsSummary Controls Copy Lighting Plate Instructions Normal Operating Sounds GAS AppliancesMaintenance Control Module FAN ReplacementSolenoid Valve Front Air Box Valve ReplacementFender Back BurnerDC Sparker Replacement Heat Shield Power Module ReplacementControl Module Replacement Backup Battery ReplacementParts List Main AssemblyDescription Valve Tray Assembly Flush Door & Louvers Regency P40 Direct Vent Gas Fireplace Regency P40 Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

P40, P40-LP, P40-NG specifications

The Regency P40 series, comprising the P40-LP, P40, and P40-NG models, represents a significant advancement in the world of portable radio communications. Designed with both versatility and performance in mind, these devices cater to a diverse range of users, from public safety professionals to outdoor enthusiasts.

One of the standout features of the P40 series is its robust build quality. The radios are engineered to withstand harsh environments, boasting IP67 water and dust resistance ratings. This ensures reliable performance even in challenging conditions, making them ideal for emergency responders who operate in adverse weather or rugged terrains. The P40's durable design is complemented by a lightweight construction, allowing for prolonged use without fatigue.

The P40 series is equipped with advanced digital technology that enhances both audio clarity and range. With a powerful speaker and noise-canceling capabilities, users can communicate clearly even in noisy surroundings. The P40-NG model takes this a step further by incorporating digital signal processing (DSP) technology, which optimizes sound for both transmission and reception.

Battery life is a critical aspect of any portable device, and the P40 series excels in this regard. With options for high-capacity lithium-ion batteries, users can expect extended operational times, vital for those on long shifts or field operations. Additionally, the smart battery management system provides real-time battery status updates, ensuring users are never caught off guard.

Interoperability is another key characteristic of the P40 series. The radios support multiple frequency bands and can seamlessly integrate with existing communication infrastructures. This capability is particularly beneficial for agencies that require coordination across various channels and networks.

User-friendly interfaces define the P40 series, with intuitive controls and customizable features. The color display on the P40 and P40-NG models enhances usability, allowing for easy navigation through settings and features. Furthermore, programmable buttons facilitate quick access to frequently used functions, ensuring efficient communication even in high-pressure scenarios.

Overall, the Regency P40-LP, P40, and P40-NG radios embody reliability, advanced technology, and ruggedness, making them essential tools for effective communication in a variety of demanding environments. With their combination of durability, audio performance, and battery life, these radios stand out as a top choice for both professional and recreational use.
Top Page Image Contents