Regency L234-LP, L234-NG Optional Remote Control, Optional Wall Thermostat, Final Check

Page 28

INSTALLATION

INSTALLATION

OPTIONAL REMOTE

CONTROL

IMPORTANT

Due to the extreme heat this gas insert emits, brick panels are required to be installed in the unit when using either remote control option.

Use of FPI Remote Control Kit #910-399 or #910-368 is approved for this unit. Use of other systems may void your warranty.

The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate.

Refer to Remote Control manual for complete

user setup and operation instructions.

Remote Receiver Installation

1)Remove the control switch from the remote receiver by gently pulling out.

Control

Switch

Remote

Receiver

4)Re-install the control switch and the battery pack (with batteries).

5)Remove the peel off from the velcro on the receiver bracket on the left side of the unit.

6)Secure the receiver to the velcro on the recevier bracket.

Receiver

Receiver Bracket

7)Run the receiver wires under the base of the fi rebox to the left side of the unit.

OPTIONAL WALL

THERMOSTAT

A wall thermostat may be installed if desired, follow the wiring diagram below. Note: the wires are connected to the "TH" on the gas valve. Use the table below to determine the maximum wire length. FPI offers an optional programmable thermostat but any 250-750 millivolt rated non- anticipator type thermostat that is CSA, ULC or UL approved may be used.

It is recommended that the thermostat be installed on an interior wall.

CAUTION

Do not connect the millivolt

wall thermostat wires

to the 120V wires.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

Wire Size

Max. Length

14 GA.

50

Ft.

16 GA.

32

Ft.

18 GA.

20

Ft.

20 GA.

12

Ft.

22 GA.

9

Ft.

2)Remove the spring loaded battery pack by pushing in and then pulling out.

Battery

Pack

3)Remove the receiver from the bracket and discard the bracket.

8)Connect the reciever wires to the valve.

9)Secure the loose wires under the fi rebox in the wire clips located on the base of the fi rebox.

FINAL CHECK

Before leaving this unit with the customer, the installer must ensure that the appliance is fi ring correctly. This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label) at 15 minutes.

2)Ifrequired,adjustingtheprimaryairtoensure that the fl ame does not carbon. First allow the unit to burn for 15 min. to stabilize.

3)Check for proper draft.

CAUTION

Any alteration to the product that causes sooting or carboning that results in damage to the exterior facia is not the responsibility of the manufacturer.

BracketReceiver

28

Regency® L234 Direct Vent Gas Insert

Page 27 Page 29
Image 28
Page 27 Page 29
Contents L234 Gas Insert Regency GAS Fireplace Insert Table of Contents Safety Label Requirements MA Code CO DetectorUnit & Faceplate Dimensions Installation Materials Required Installation ChecklistMinimum Fireplace Opening Minimum Clearances to Combustible Mantel Combustibles Installation with 3 & 3 Liners VentingVent Restrictor Position Converting from 3 & 3 Venting to 3Flue Liner GAS Connection Installation GAS Insert Aeration SystemGAS Pipe Pressure Testing SIT Valve DescriptionConversion KIT #536-969 from NG to LP Top Mounting BracketBurner Removed Spring HookRemove burner orifice with a 1/2 wrench Optional Brick Panel Installation Faceplate Contents List Contour or Contemporary FaceplateDC Sparker Remote Receiver BracketCompleted Faceplate Installation Attach Top Backing Plate to Faceplate Optional Backing PlateAttach Faceplate & Top Backing Plate to Unit Attach Left & Right Corner Backing Plate Attach Left & Right Backing Plate to FaceplateOptional Hearth Trim Customize Hearth TrimLOG SET Installation 711 713 7152-716 712 714Notch TabRight side of Burner Completed Log Set Installation Wiring Diagrams Optional Wall Thermostat Optional Remote ControlFinal Check Lighting Procedure Shutdown ProcedureOperating Instructions First FireCopy of Lighting Instruction Plate FAN OperationMaintenance FAN Replacement Connector Clips Valve Replacement DC Sparker WiresValve Removed Parts List Main AssemblyFaceplate Assembly Backing Plate & Hearth Trim Assembly Warranty ConditionsInstaller Please complete the following information

L234-NG, L234-LP specifications

The Regency L234-LP and L234-NG are elegant and efficient gas fireplaces that exemplify modern design and advanced technology. These models are ideal for homeowners looking to enhance their living spaces with warmth and aesthetics. With a variety of features, the Regency L234 fireplace series stands out in both functionality and style.

One of the key characteristics of the L234 series is its choice between liquid propane (LP) and natural gas (NG) configurations, providing flexibility for various installation needs. This adaptability allows homeowners to select the fuel type that best suits their preferences and available resources.

In terms of design, the L234 fireplaces feature a contemporary clean face style, which emphasizes the stunning flames while minimizing distractions. The large viewing area is framed by a sleek, minimalist design that fits effortlessly into modern interiors. With customizable options, including different decorative media such as glass and stones, consumers can personalize the appearance of their fireplace to match their home decor.

Efficiency is another hallmark of the Regency L234 series. With its high-efficiency rating, this fireplace not only produces warmth but does so while minimizing fuel consumption. The incorporation of advanced technology such as a direct vent system allows for safe and efficient combustion, drawing in outdoor air for combustion and venting exhaust gases outside. This feature enhances the overall efficiency of the unit, ensuring the living space remains warm and comfortable.

The L234 also comes equipped with a user-friendly remote control, simplifying the operation and allowing users to adjust flame height and heat output from a distance. This remote capability enhances convenience and allows for immediate adjustments based on comfort levels.

Safety features are paramount in the design of the Regency L234 fireplaces. The units are equipped with automatic shut-off systems and advanced safety screens to prevent accidents, providing peace of mind to homeowners.

Overall, the Regency L234-LP and L234-NG gas fireplaces are exemplary choices for those seeking a blend of modern design, efficiency, and safety. With their customizable features and advanced technologies, they provide not only heating solutions but also a stylish focal point for any room. As homeowners seek eco-friendly alternatives that do not compromise on style, the Regency L234 series stands out as a top contender in the market.
Top Page Image Contents