Regency E21-LP1, E21-NG1 Offset Flue Adaptor, Venting, GAS Pipe Pressure Testing

Page 10

INSTALLATION

OFFSET FLUE

ADAPTOR

A Offset Flue Adaptor Kit, Part #532-920 is available as an accessory to move the fl ue outlet back for easier liner installations in deep fi replaces.

VENTING

THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE.

This appliance is designed to attach to a 4" diameter type B-Vent or double thickness approved aluminium fl ex liner.

The fl ue collar of the appliance will fi t inside a standard vent and may be fastened directly to the vent by sheet metal screw or a B-Vent, single wall vent connector.

B-Vent chimneys require a 1" clearance to combustibles.

A3" diameter type B-Vent or approved aluminium

flex liner may also be used with a 4" to 3" reduc- ing adapter. Consult venting charts and local code requirements.

The Regency Insert incorporates its own internal draft hood, so no additional external draft hood is required. Check periodically that the vent is unrestricted and an adequate draft is present when the unit is in operation.

Before installing the vent system ensure that the damper plate is locked into the open position and secure to prevent the damper plate from falling down and crushing the liner.

The appliance is equipped with a vent safety shutoff system and a safety control system designed to protect against improper venting of combustion products. The appliance will not function without being connected to a proper system.

WARNING: Operation of this heater when not connected to a properly installed and maintained venting system or tampering with the vent shut-off system can result in carbon monoxide (CO) poisoning and possible death.

This appliance must not be connected to a chimney fl ue serving a separate solid fuel burn- ing appliance.

For best venting performance, we recommend the following venting rules:

1)Use only certifi ed Type B gas vent or approved fl ex liner.

2)Follow the vent manufacturer's instructions and clearance requirements.

3)Observe any local code restrictions, if any, regarding the installation of gas inserts.

4)Use as few elbows as possible.

5)Keep horizontal lengths as short as possible and maintain at least an upward slope of 1/4 in. (6.4mm) for every 12 in. (305mm) of horizontal run.

6)Terminate the vent with a suitable certifi ed vent cap.

COMBUSTION AND VENTILATION AIR

WARNING: This appliance needs fresh air for safe operation and must be installed with provisions for adequate combustion and ventilation air available to the room in which it is to be operating.

Follow CAN/CGA B149 (in Canada) or ANSI Z223.1 (in the USA) requirements, and any local codes or regulations of the enforcing authority.

Air for combustion is drawn in through the front of the unit, therefore, the front of the unit must be kept clear of any obstructions.

GAS PIPE

PRESSURE TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" position.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide fl at screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position. Read manometer.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits specifi ed on the safety label.

6)When fi nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver. Note: Screw should be snug, but do not over tighten

10

Regency E21 Gas Fireplace Insert

Page 9 Page 11
Image 10
Page 9 Page 11
Contents E21 Gas Insert 918-354a 10/25/05Congratulations You are the owner of a state-of-the-art Gas Insert byTable of Contents Approved for bedroom installations Safety LabelFor the State of Massachusetts, installation Save These Instructions InstallationBefore YOU Start Installation Checklist Minimum Fireplace ClearancesIf the framing is made of metal studs covered with a non Clearances to CombustiblesCombustible board System Data GAS ConnectionHigh Elevation Natural Gas Propane Burner #43 #54Grounding Wiring Diagram for the E21-NG1 and E21-LP1Lug Detail Offset Flue Adaptor GAS Pipe Pressure TestingVenting Optional Brick Panel GAS Insert Aeration SystemTest for Flue Spillage Valve DescriptionPlace the Front Left Log B 02-67 on the 2 front pins LOG SET InstallationFaceplate & Trim Installation A02-66 D02-70 C02-68 B02-67 E02-69Switch Power cord should be run behind the faceplate panelFlush Glass Flush Louvers Are different. See diagram belowBAY Louvers Conversion Kit from Natural Gas to Propane Model #533-969 Installation Full Screen Front Close screen doors Wire Size Thermostat Wire TableConnect the two wires to the gas valve. See diagram below Wall ThermostatOperating Instructions For Your Safety Read Before Lighting Copy of Lighting Plate InstructionsMaintenance Flush Glass Replacement Door Glass ReplacementRemoving Valve Assembly Removing the FANParts List DescriptionBurner Assembly & LOG SET Bay Door Flush DoorFaceplate Standard-Contour- Side Left Faceplate Standard-Contour- Side RightFaceplate Standard-Contour-Top Faceplate Standard-Contour- Trim RightRegency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Warranty ConditionsInstaller Please complete the following information

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.
Top Page Image Contents