Regency installation manual Wiring Diagram for the E21-NG1 and E21-LP1, Grounding, Lug Detail

Page 9

INSTALLATION

WIRING DIAGRAM FOR THE E21-NG1 AND E21-LP1

This heater does not require a 120VA.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/ thermostat will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

When connected with 120 volts, the appliance must be electrically grounded in accordance with local codes or, in the absence of local

codes the current CSA C22.1 (in Canada) or with the National Electrical Code ANSI/NFPA 70-1987 (in USA).

NOTE: This unit is equipped with a heat sensor thermodisc which will prevent the blower from operating until the unit reaches the correct temperature.

#8 Ground Lug

Grounding

Nut

Lug Detail

Lockwasher

Fan ground

 

Star washer

Nut

Power cord ground wire

Star washer

Pilot

Assembly

Thermopile

GasPilot

Electrode

 

Ground

Green

 

 

 

Fan

 

 

 

Neutral

 

 

 

120V AC Live

Ground

 

 

 

 

60 Hz

 

ON

OFF

 

 

 

 

Red Black

Black

Fan

Rotary Speed

Control

Thermodisc

 

Black

Gas

In

 

 

 

Thermocouple In

 

 

 

 

 

 

 

Piezo

 

 

 

 

 

 

 

Ignitor

 

 

 

P

 

O

H

 

 

Black

ON

ILO

T

 

N

 

 

 

 

 

 

 

I

White

 

 

Burner

 

 

FO

OL

 

 

 

 

F

 

 

 

 

 

 

 

 

 

Brown

 

Red

OFF

"S.I.T" Valve

Red

 

 

 

 

 

 

 

 

 

 

 

 

OFF ON

Thermostat

Remote Transmitter

 

 

 

 

Vent Spill

 

 

 

 

 

Switch

Remote

(Millivolt)

(Optional)

 

 

 

 

(Auto Reset)

Receiver

(Optional)

Regency

 

 

 

 

 

(Optional)

 

 

 

 

 

 

(Millivolt)

 

 

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

WARNING: Electrical Grounding

Instructions

This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into

aproperly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

FLUE CONNECTOR INSTALLATION

1)Remove the screw holding the fl ue connector plate to the appliance.

2) Slide the plate out and attach to the fl ue liner inside the fi replace to the fl ue collar with three sheet metal screws.

3) Place the appliance on the hearth. Push the appliance into the fi re- place and at the same time slide the plate back onto the appliance.

4)Replace the screw holding the plate just before completely pushing the appliance into the fi replace.

Note: Do not operate unit if flue connector is not fastened in original position.

Regency E21 Gas Fireplace Insert

9

Image 9
Contents 918-354a 10/25/05 E21 Gas InsertYou are the owner of a state-of-the-art Gas Insert by CongratulationsTable of Contents Safety Label Approved for bedroom installationsFor the State of Massachusetts, installation Installation Save These InstructionsBefore YOU Start Minimum Fireplace Clearances Installation ChecklistClearances to Combustibles If the framing is made of metal studs covered with a nonCombustible board High Elevation GAS ConnectionSystem Data Natural Gas Propane Burner #43 #54Wiring Diagram for the E21-NG1 and E21-LP1 GroundingLug Detail GAS Pipe Pressure Testing Offset Flue AdaptorVenting Test for Flue Spillage GAS Insert Aeration SystemOptional Brick Panel Valve DescriptionFaceplate & Trim Installation LOG SET InstallationPlace the Front Left Log B 02-67 on the 2 front pins A02-66 D02-70 C02-68 B02-67 E02-69Power cord should be run behind the faceplate panel SwitchFlush Glass Are different. See diagram below Flush LouversBAY Louvers Conversion Kit from Natural Gas to Propane Model #533-969 Installation Full Screen Front Close screen doors Connect the two wires to the gas valve. See diagram below Thermostat Wire TableWire Size Wall ThermostatOperating Instructions Copy of Lighting Plate Instructions For Your Safety Read Before LightingMaintenance Removing Valve Assembly Door Glass ReplacementFlush Glass Replacement Removing the FANDescription Parts ListBurner Assembly & LOG SET Flush Door Bay DoorFaceplate Standard-Contour-Top Faceplate Standard-Contour- Side RightFaceplate Standard-Contour- Side Left Faceplate Standard-Contour- Trim RightRegency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Conditions WarrantyInstaller Please complete the following information

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.