Regency E21-NG1, E21-LP1 GAS Insert Aeration System, Test for Flue Spillage, Optional Brick Panel

Page 11

INSTALLATION

Valve Description

1)Gas cock knob

2)Manual high/low adjustment

3)Pilot Adjustment

4)Thermocouple Connection

5)Main Operator

6)Outlet Pressure Tap (Manifold Pressure)

7)Inlet Pressure Tap (Supply Pressure)

8)Pilot Outlet

9)Main Gas Outlet

10)Flange Securing Screw Holes

11)Alternative TC Connection Point

12)Thermoelectric Unit

13)Additional Valve Mounting Hole

GAS INSERT AERATION

SYSTEM

The aeration adjustment rod is attached to the air shutter which is located just above the orifi ce bracket. The rod is used to adjust the aeration on the main burner without having to take the appliance apart.

The burner aeration is factory set but may need adjusting due to either the local gas supply, air supply or altitude.

Natural Gas:

1/8" (3.2mm) open

Propane:

3/16" (4.8mm) open

Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.

Note: Aeration Adjustment should only be performed by an authorized Regency Installer at the time of installation or service.

TEST FOR

FLUE SPILLAGE

A " spillage" test must be made before the installed unit is left with the customer. Follow the procedure below:

1)Close all external doors and windows in the house.

2)Light the unit and set controls to maximum. Turn fan to OFF on unit.

3)After fi ve minutes, test that there is a “pull” on the fl ue by placing a smoking match, cigarette or similar device which gives off smoke, in front of the upper part of the louver. To ensure a valid test, place

a scrap piece of sheet metal (or other noncombustible material) in the upper louver, this will prevent the natural convection of the unit from interfering with the test.

Note: The smoke should be drawn into the louver. If the smoke is still not drawn in, turn the unit off and check for the cause of the lack of draft. If necessary, seek expert advice.

OPTIONAL

BRICK PANEL

1)Unwrap the brick pattern panels from the protective wrapping.

2)With the glass removed, position the back panel fi rst (see diagram for correct positioning), then the two side panels. Slide the side brick panel into place from the front of the fi rebox, there is a tab at the top of the unit to hold the side panels in place.

3)The brick panels should be tight against the fi rebox sides and back. The side panels should be fl ush with the glass.

Note: Use caution when sliding side panels in as they can easily be scratched by the brick panel tabs.

Regency E21 Gas Fireplace Insert

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 918-354a 10/25/05 E21 Gas InsertYou are the owner of a state-of-the-art Gas Insert by CongratulationsTable of Contents For the State of Massachusetts, installation Safety LabelApproved for bedroom installations Before YOU Start InstallationSave These Instructions Minimum Fireplace Clearances Installation ChecklistCombustible board Clearances to CombustiblesIf the framing is made of metal studs covered with a non Natural Gas Propane Burner #43 #54 GAS ConnectionHigh Elevation System DataLug Detail Wiring Diagram for the E21-NG1 and E21-LP1Grounding Venting GAS Pipe Pressure TestingOffset Flue Adaptor Valve Description GAS Insert Aeration SystemTest for Flue Spillage Optional Brick PanelA02-66 D02-70 C02-68 B02-67 E02-69 LOG SET InstallationFaceplate & Trim Installation Place the Front Left Log B 02-67 on the 2 front pinsFlush Glass Power cord should be run behind the faceplate panelSwitch BAY Louvers Are different. See diagram belowFlush Louvers Conversion Kit from Natural Gas to Propane Model #533-969 Installation Full Screen Front Close screen doors Wall Thermostat Thermostat Wire TableConnect the two wires to the gas valve. See diagram below Wire SizeOperating Instructions Copy of Lighting Plate Instructions For Your Safety Read Before LightingMaintenance Removing the FAN Door Glass ReplacementRemoving Valve Assembly Flush Glass ReplacementDescription Parts ListBurner Assembly & LOG SET Flush Door Bay DoorFaceplate Standard-Contour- Trim Right Faceplate Standard-Contour- Side RightFaceplate Standard-Contour-Top Faceplate Standard-Contour- Side LeftRegency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Conditions WarrantyInstaller Please complete the following information

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.
Top Page Image Contents