Regency E21-LP1 GAS Connection, High Elevation, System Data, Natural Gas Propane Burner #43 #54

Page 8

INSTALLATION

GAS CONNECTION

Only persons licensed to work with gas piping may make the necessary gas connections to this appliance.

The gas connection is a 3/8" NPT accessible on the left side of the unit. The gas line connection may be made of rigid pipe, copper pipe or an approved fl ex connector. (If you are using rigid pipe, ensure that the valve can be removed for servicing.) Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or fl ex connectors use only approved fi ttings.Always provide a union so that gas lines can be easily disconnected for burner or fan servicing. Flare nuts for copper lines and

flex connectors are usually considered to meet this requirement.

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open flame for leak testing.

For minimum and maximum supply pressure see the System Data table.

1)If the appliance is to be installed into an existing chimney system, thoroughly clean the masonry fi replace that has been chosen for the Regency Gas Fireplace.

2)The appliance is provided with an opening on the left hand side of the control compartment for the gas line.

Note: During any pressure testing of the gas supply piping system that exceeds test pressures of 1/2 psig, this appliance and its individual shut-off valve must be disconnected from the piping system. If test pressures equal to or less than 1/2 psig are used then this appliance must be isolated from the piping system by closing its individual manual shut-off valve during the testing.

CAUTION: If the glass is removed for servicing, it must be replaced prior to operating the appliance. The glass must be fixed in the closed position when operating.

System Data

For altitude:

Natural Gas

0-2000 ft.

 

Propane:

0-4500 ft.

Burner Inlet Orifice Sizes:

 

 

Natural Gas

Propane

Burner

 

#43

#54

Max. Input Rating

 

 

- Natural Gas

23,500 Btu/h

- Propane

 

22,500 Btu/h

Min. Input Rating

 

 

Natural Gas +/-5%

11,750 Btu/h

-Propane

+/-5%

11,250 Btu/h

Supply Pressure

 

 

Natural Gas

 

min.

5.0" w.c.

Propane

 

min.

12.0" w.c.

Manifold Pressure (High)

 

Natural Gas

 

3.8"

+/- 0.2" w.c.

Propane

 

11"

+/- 0.2" w.c.

Circulation Fan: 120 VAC, 60 Hz

Variable Speed: 127 CFM, thermally

activated

 

 

 

NATURAL GAS E21-NG1

For altitude:

2000 ft - 4500 ft.

Burner Inlet Orifice Size:

44 DMS

Max. Input Rating

22,000 Btu/h

Min. Input Rating

+/-5%

11,000 Btu/h

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to 4500 ft. (CAN/CGA 2.17-M91) with the orifi ce supplied.

8

Regency E21 Gas Fireplace Insert

Page 7 Page 9
Image 8
Page 7 Page 9
Contents E21 Gas Insert 918-354a 10/25/05Congratulations You are the owner of a state-of-the-art Gas Insert byTable of Contents For the State of Massachusetts, installation Safety LabelApproved for bedroom installations Before YOU Start InstallationSave These Instructions Installation Checklist Minimum Fireplace ClearancesCombustible board Clearances to CombustiblesIf the framing is made of metal studs covered with a non GAS Connection High ElevationSystem Data Natural Gas Propane Burner #43 #54Lug Detail Wiring Diagram for the E21-NG1 and E21-LP1Grounding Venting GAS Pipe Pressure TestingOffset Flue Adaptor GAS Insert Aeration System Test for Flue SpillageOptional Brick Panel Valve DescriptionLOG SET Installation Faceplate & Trim InstallationPlace the Front Left Log B 02-67 on the 2 front pins A02-66 D02-70 C02-68 B02-67 E02-69Flush Glass Power cord should be run behind the faceplate panelSwitch BAY Louvers Are different. See diagram belowFlush Louvers Conversion Kit from Natural Gas to Propane Model #533-969 Installation Full Screen Front Close screen doors Thermostat Wire Table Connect the two wires to the gas valve. See diagram belowWire Size Wall ThermostatOperating Instructions For Your Safety Read Before Lighting Copy of Lighting Plate InstructionsMaintenance Door Glass Replacement Removing Valve AssemblyFlush Glass Replacement Removing the FANParts List DescriptionBurner Assembly & LOG SET Bay Door Flush DoorFaceplate Standard-Contour- Side Right Faceplate Standard-Contour-TopFaceplate Standard-Contour- Side Left Faceplate Standard-Contour- Trim RightRegency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Warranty ConditionsInstaller Please complete the following information

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.
Top Page Image Contents