Regency E21-NG1 Copy of Lighting Plate Instructions, For Your Safety Read Before Lighting

Page 21

OPERATING INSTRUCTIONS

COPY OF LIGHTING PLATE INSTRUCTIONS

FOR YOUR SAFETY READ

BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installations Codes, CSA B149.1. Australia: AG601, New Zealand: NZS 5261

WARNING: If you do not follow these instruc- tions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjust- ment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or addi- tional information consult a qualified installer, service agency or gas supplier.

A)This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B)BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

C)Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified Service Technician. Force or attempted repair may result in a fire or explosion.

D)Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface temperatures keep children, clothing and furniture, gasoline and other liquids having flammable vapors away. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

LIGHTING INSTRUCTIONS

STOP! Read the safety information above on this label.

1)Push in gas control knob slightly and turn

clockwise to “OFF”. Knob cannot be

turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

2)Wait five (5) minutes to clear out any gas If you then smell gas STOP! follow “B” in the safety information above on this label. If you don’t smell gas, go to the next step.

3)Turn knob on gas control counterclockwise to“PILOT”

4)Push in control knob all the way and hold in. Continually push and release the black button on spark igniter until pilot lights. Continue to hold the control knob in for about 1/2 minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 1) to 4). If knob does not pop up when released, stop and immediately call your service technician or gas supplier. If the pilot will not stay lit after several tries, turn the gas control knob to OFF” and call your service technician or gas supplier.

5)Turn gas control knob counterclock-wise to “ON”

6)Use rocker switch to operate main burner.

TO TURN OFF GAS APPLIANCE

1)Push in the gas control knob slightly and turn clockwise to “OFF”. Do not force.

2)Turn off all electric power to the appliance

if service is to be performed. 918-048a

DO NOT REMOVE THIS INSTRUCTION PLATE

Regency E21 Gas Fireplace Insert

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 918-354a 10/25/05 E21 Gas InsertYou are the owner of a state-of-the-art Gas Insert by CongratulationsTable of Contents Safety Label Approved for bedroom installationsFor the State of Massachusetts, installation Installation Save These InstructionsBefore YOU Start Minimum Fireplace Clearances Installation ChecklistClearances to Combustibles If the framing is made of metal studs covered with a nonCombustible board High Elevation GAS ConnectionSystem Data Natural Gas Propane Burner #43 #54Wiring Diagram for the E21-NG1 and E21-LP1 GroundingLug Detail GAS Pipe Pressure Testing Offset Flue AdaptorVenting Test for Flue Spillage GAS Insert Aeration SystemOptional Brick Panel Valve DescriptionFaceplate & Trim Installation LOG SET InstallationPlace the Front Left Log B 02-67 on the 2 front pins A02-66 D02-70 C02-68 B02-67 E02-69Power cord should be run behind the faceplate panel SwitchFlush Glass Are different. See diagram below Flush LouversBAY Louvers Conversion Kit from Natural Gas to Propane Model #533-969 Installation Full Screen Front Close screen doors Connect the two wires to the gas valve. See diagram below Thermostat Wire TableWire Size Wall ThermostatOperating Instructions Copy of Lighting Plate Instructions For Your Safety Read Before LightingMaintenance Removing Valve Assembly Door Glass ReplacementFlush Glass Replacement Removing the FANDescription Parts ListBurner Assembly & LOG SET Flush Door Bay DoorFaceplate Standard-Contour-Top Faceplate Standard-Contour- Side RightFaceplate Standard-Contour- Side Left Faceplate Standard-Contour- Trim RightRegency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Regency E21 Gas Fireplace Insert Conditions WarrantyInstaller Please complete the following information

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.
Top Page Image Contents