Regency 510-994, 946-523/P P33-NG4 w P33-LP4 w Model, August 2008 Product Specifications Book

Gas Fireplaces

		P33-NG4 w/	P33-LP4 w/
Model		Contemporary	Contemporary
		Faceplate	Faceplate
Fuel Type		Natural Gas	Propane
Minimum Supply Pressure		5” W.C. (1.25 kPa)	12” W.C. (3.00 kPa)
Manifold Pressure - High		3.8” W.C. (0.95 kPa)	11” W.C. (2.74 kPa)
Manifold Pressure - Low		1.1” W.C. (0.27 kPa)	3.3” W.C. (0.82 kPa)
Orifice Size		#47 DMS	#56 DMS
Minimum Input		9,800 BTU/h	9,000 BTU/h
Altitude 0-4500 ft. (0-1372m)		(2.87 kW)	(2.64 kW)
Maximum Input		17,500 BTU/h	15,500 BTU/h
Altitude 0-4500 ft. (0-1372m)		(5.13 kW)	(4.54 kW)
Vent Sizing	4” Inner / 6 5/8” Outer		4” Inner / 6 5/8” Outer
Approved Venting Systems
Flex Vent Systems:		FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems:		Simpson Direct Vent Pro®
		American Metal Products® Amerivent Direct
		Security Secure Vent®
		Selkirk Direct-Temp™
		Metal-Fab® Sure Seal

P33 Gas Fireplace

Gas Fireplaces

Unit Dimensions Description P33 with Contemporary Faceplate

A	Front Face Width		33” (838mm)
B	Rear Firebox Width		23” (584mm)
C	Front Face Height		29” (737mm)
D	Height w/ Standoff		31 1/2” (800mm)
E	Unit Depth		12-3/4” (324mm)
F	Firebox Height		29” (737mm)
Framing Dimensions	Description		P33 with Contemporary Faceplate
G	Framing Width		33-1/4” (845mm)
H**	Framing Height**		31-3/4” (806mm)**
I*	Framing Rise from Floor		1” (25mm) minimum*
J	Framing	Vertical	19 1/2” (495mm) Vertical Rise
	Depth	Horizontal	16 1/2” (419mm) Rigid	12-3/4” (324mm) Flex
K	Corner Wall Length		37 1/2” (953mm)
L	Corner Facing Wall Width		53-1/4” (1353mm)
M***	Framed Chase Ceiling***		36” (914mm) Rigid***	32” (813mm) Flex***
N	Vent Centerline Height		30” (762mm) Rigid	26” (660mm) Flex

*The unit must be raised a minimum of 1” above the finished floor.

**Dimension H = H + I (minimum)

***Dimension M = M + I (minimum)

Dimension	Description	P33S
O	Gas Connection Height	1 1/2” (38mm)
P	Gas Connection Inset	4” (102mm)
Q	Gas Connection Width	3” (76mm)
R	Minimum Framing Depth	16 1/2” (419mm) Rigid	/	12-3/4” (324mm) Flex
S	Maximum Framing Depth	40 1/2” (1028mm) Rigid	/	36-3/4” (933mm) Flex
	(including wall thickness)

Important:

If the Contemporary Faceplate is used on the P33-NG4/P33- LP4 Gas Fireplace, the burner orifice (Both NG/LP supplied in package) must be replaced and an overlay decal (also supplied with kit) must be affixed to the current serial number decal supplied with unit.

Note: Also see framing dimensions for this optional front if installed on the P33-4 unit.

Note: Unit must be raised up by 1' to allow for faceplate installation.

	NG	LP
Current P33-4 orifice size: #44		#54
Must replace with:	#47	#56

Warning: Fire hazard is an extreme risk if these changes are not adhered to.

August 2008 Product Specifications Book 29