Nilfisk-Advance America SW 700S P Use, Before Starting the Machine, Starting the machine

Page 52

ENGLISH

USER MANUAL

USE

WARNING!

On some points of the machine there are some adhesive plates indicating:

–DANGER

–WARNING

–CAUTION

–CONSULTATION

While reading this Manual, the operator must pay careful attention to the symbols shown on the plates. Do not cover these plates for any reason and immediately replace them if they are damaged.

BEFORE STARTING THE MACHINE

1.Make sure that the debris container (17) is properly closed before starting the machine.

2.If necessary, remove the cap (27) and refuel the machine.

CAUTION!

Do not fill the fuel tank beyond the upper limit mark (A, Fig. 1).

STARTING AND STOPPING THE MACHINE

Starting the machine

1.Adjust the handlebar (3) with the knobs (5).

2.Ensure that the side broom (10) is lifted.

3.Open the fuel tap (A, Fig. 2) by introducing the hand into the compartment (29) without opening the hood (7).

4.Turn the engine choke lever (A, Fig. 3) to closed position

(B) by introducing the hand into the compartment (29) without opening the hood (7).

NOTE

Do not close the choke lever if the engine is hot and if the air temperature is sufficiently high.

5.Turn the ignition key (71) to "I".

6.Pull slowly the engine pull-start cord handle (28) until a certain resistance is achieved; then pull suddenly and strongly and start the engine.

CAUTION!

Do not allow the handle (28) to return strongly but bring it back to its position slowly, to prevent the starting system from being damaged.

CAUTION!

When starting the engine with the handle (28) do not pull the drive lever (4).

S311480

Figure 1

S311481

Figure 2

S311482

Figure 3

10

146 0676 000(5)2007-06 A

SW 700S P

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Sweeper SW 700S P 146 0676 00052007-06 aSweeper SW 700S PInhaltsverzeichnis EinleitungEinleitung AUSPACKEN/AUSLIEFERUNG SicherheitAllgemeine Hinweise Betriebsanleitung Deutsch Maschinenbeschreibung MaschinenaufbauMaschinenaufbau fortgesetzt Schalttafel ZUBEHÖRE/OPTIONENSchaltplan Technische DatenFarbencodes Betrieb VOR DEM AnlassenMaschinenanlassen UND -ABSTELLEN MaschinenanlassenMaschine in Betrieb MaschinenabstellenWartung Bei Einlaufzeit Alle Vorgang Übersichtstabelle DER Planmässigen WartungStunden Prüfung UND Einstellung DER Hauptkehrwalzenhöhe Ersetzen DER Hauptkehrwalze Prüfung UND Einstellung DER Seitenbesenhöhe Ersetzen DES SeitenbesensReinigung UND Vollständigkeitsprüfung DES Staubfilters Prüfung UND Einstellung DER Flapshöhe Prüfung der SeitenflapsFlap rechts Flap linksPrüfung der Vorder- und Hinterflaps Verschrottung FehlersucheFehler Mögliche Ursache Lösung Table DES Matieres IntroductionIntroduction Deballage / Livraison SecuriteInstructions Generales Manuel Dutilisation Français Description DE LA Machine Structure DE LA MachineStructure DE LA Machine suite Accessoires / Options Tableau DE BordCaracteristiques Techniques Schema ElectriqueLégende Codes des couleurs Utilisation Avant LA Mise EN MarcheMise EN Marche ET Arret DE LA Machine Mise en marche de la machineMachine AU Travail Arrêt de la machineEntretien Plan Dentretien Programme Toutes ProcédureLes HeuresControle ET Reglage DE LA Hauteur DU Balai Central Remplacement DU Balai Central Remplacement DU Balai Lateral Controle ET Reglage DE LA Hauteur DU Balai LateralNettoyage ET Controle DE Lintegrite DU Filtre a Poussiere Controle ET Reglage DE LA Hauteur DES Volets Contrôle des volets latérauxVolet droit Volet gaucheContrôle des volets avant et arrière Mise EN Decharge Depistage DES PannesProblème Cause probable Remède Table of Contents Manual Purpose and Contents HOW to Keep this Manual Declaration of ConformityTarget Identification DataSafety UNPACKING/DELIVERYGeneral Instructions English Machine Description Machine StructureMachine Structure Continues ACCESSORIES/OPTIONS Control PanelWiring Diagram Technical DataKey Colour code USE Before Starting the MachineStarting and Stopping the Machine Starting the machineMachine Operation Stopping the machineMaintenance Scheduled Maintenance Table Upon deli Running-in Every Procedure 100300 HoursMain Broom Height Check and Adjustment Main Broom Replacement Side Broom Height Check Adjustment Side Broom ReplacementDust Filter Cleaning and Integrity Check Skirt Height Check and Adjustment Side skirt checkHood Safety Switch Operation Check Left skirtRight skirt Front and rear skirt checkScrapping TroubleshootingTrouble Possible cause Remedy Inhoudsopgave InleidingInleiding Verpakking VERWIJDEREN/AFLEVERING VeiligheidAlgemene Instructies Gebruiksaanwijzing Nederlands Beschrijving VAN DE Machine Bouw VAN DE MachineOpbouw VAN DE Machine vervolg Accessoires / Opties BedieningspaneelTechnische Eigenschappen Elektrisch SchemaKleurcodering Gebruik Voor HET StartenDE Machine Starten EN Stoppen Starten van de machineMachine in Bedrijf De machine stoppenOnderhoud Onderhoudsschema Inloopperi ElkeDE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DE Hoofdborstelvervangen DE Hoogte VAN DE Zijborstel Controleren EN Afstellen DE Zijborstel VervangenReiniging EN Contole OP Integriteit VAN HET Stoffilter DE Hoogte VAN DE Flaps Controleren EN Afstellen Controle van de zijflapsRechterflap LinkerflapControle van de voor- en achterflap Verwijdering Storingen LokaliserenProbleem Waarschijnlijke oorzaak Oplossing

SW 700S P specifications

The Nilfisk-Advance America SW 700S P is an innovative and efficient machine that stands out in the realm of commercial cleaning equipment. Designed for optimal performance and user convenience, the SW 700S P combines state-of-the-art technology with robust features aimed at streamlining the cleaning process in a variety of industrial and commercial settings.

One of the standout features of the SW 700S P is its compact design, which allows for excellent maneuverability in tight spaces. This is particularly beneficial in environments such as retail stores, schools, and warehouses where space can often be limited. The machine’s low profile ensures that it can easily navigate around obstacles, providing thorough cleaning without disrupting daily operations.

Equipped with a powerful yet efficient motor, the SW 700S P delivers impressive cleaning capabilities. It utilizes a dual-suction system that maximizes dirt and debris pickup, ensuring a consistently clean surface. This technology not only enhances cleaning efficiency but also minimizes the need for frequent emptying of the waste container, allowing operators to focus on their tasks without interruption.

The machine incorporates user-friendly controls, making it accessible for operators of all experience levels. The ergonomic design features an adjustable handle that ensures comfort during prolonged use. Additionally, operators can easily switch between cleaning modes, optimizing the machine for various floor types and levels of dirt accumulation.

Another noteworthy technology is the integrated battery system that provides a sustainable power source, reducing the environmental footprint of the cleaning process. The SW 700S P features rapid charging capabilities, ensuring that it can be fully recharged and ready for use in minimal time, thus maximizing productivity throughout the day.

Maintenance is simplified with the SW 700S P, as daily upkeep can be performed quickly and efficiently. The machine features easily accessible components, allowing users to conduct routine inspections and cleaning with minimal effort. This not only extends the life of the equipment but also ensures consistent performance.

In summary, the Nilfisk-Advance America SW 700S P is a pioneering cleaning solution that combines versatility, efficiency, and ease of use. Its advanced features and technologies make it an invaluable asset for businesses looking to maintain cleanliness and hygiene standards while promoting operational efficiency.
Top Page Image Contents