GSW 319594-000 manual Anode Rod Replacement, Routine Preventative Maintenance, Gas Control

Page 29

Anode Rod Replacement

To replace the anode:

1.Turn off gas supply to the water heater.

2.Shut off the water supply and open a nearby hot-water faucet to depressurize the water tank.

3.Drain approximately 20 litres (5 US gallons) of water from tank (Refer to "Draining and Flushing" for proper procedures.) Close drain valve.

4.Remove old anode rod.

5.Use Teflon® tape or approved pipe sealant on threads and install new anode rod.

6.Turn on water supply and open nearby hot-water faucet to purge air from water system.

7.Restart the water heater as directed under "Operating Your Water Heater." See the "Parts Reference Illustration" for anode rod location.

Routine Preventative Maintenance

Important: If you lack the necessary skills required to prop- erly perform this visual inspection, you should not proceed, but get help from a qualified service technician.

At least annually, a visual inspection should be made of the venting and air supply system, piping systems and main burner. Check the water heater for the following:

Build up of soot and carbon on the main burner. Check for a soft blue flame.

Leaking or damaged water and gas piping.

Presence of flammable or corrosive materials in the installation area.

Presence of combustible materials near the water heater.

Verify proper operation after servicing this water heater.

Gas Control

There are no user serviceable parts in this control. The con- trol is supplied with tamper resistant screws. DO NOT attempt to repair or adjust the control. If you experience problems, discontinue use and replace the control immedi- ately. Continuing to use a damaged control could result in fire and/or explosion.

If you wish to verify that the water heater is operating prop- erly:

1.Make sure there is power to the water heater.

2.Make sure that the gas is turned on to the water heater.

3.Initiate a call for heat by either drawing hot water from a nearby faucet or raising the temperature setting (see section “Temperature Regulation”).

4.Note any error codes that appear and proceed to the “Troubleshooting” section.

Temperature and Pressure Relief Valve

WARNING

Explosion Hazard

If the temperature and pressure relief valve is dripping or leaking, have a licensed plumber repair it.

Do not plug valve.

Do not remove valve.

Failure to follow these instructions can result in death or an explosion.

Manually operate the temperature and pressure relief valve at least once a year to make sure it is working properly (see Figure 27). To prevent water damage, the valve must be properly connected to a discharge line that terminates at an adequate drain. Standing clear of the outlet (discharged water may be hot), slowly lift and release the lever handle on the temperature and pressure relief valve to allow the valve to operate freely and return to its closed position. If the valve fails to completely reset and continues to release water, immediately shut off the manual gas valve and the cold-water inlet valve and call a qualified service technician.

Temperature and Pressure

Relief Valve

Manual Relief Valve

Discharge line to drain

Figure 27 T&P Valve Test

– 29 –

Image 29
Contents What to do if YOU Smell GAS For Your SafetyViii Troubleshooting Guide Page User Responsibilities IntroductionFor Installations in Canada II SafetyFor Installations in the United States Safety Warning Flammable VapoursFlooding/Freezing Relief Valve Requirements T&PLocation Requirements Valves For Hot Water Supply Systems, Ansi Z21.22/CSAEarthquake Zones Clearances and AccessibilityCloset Installation & Floor Surfaces Gas Supply Pressure Gas Leak TestingGas line purging Gas Operating PressuresVentilated Space Air Requirements for Canadian InstallationsAir Requirements Local Codes InstallationsExhaust Venting General Venting Layout Venting terminations and sizingUse only in well-ventilated areas Use of Solvent Cement and PrimerDo not use near flame or open fire Use only the Solvent Cement and PrimerVent pipe connection to blower Water Supply Filling the Water Heater Piping InstallationTemperature and Pressure Relief Valve Temperature and Pressure T&P Relief ValveClosed System/Thermal Expansion Discharge Line/DriptubeWiring Diagram White-Rodgers Control Flammable Vapour Sensor exploded view Flammable Vapour SensorWater Heater Operation Resettable LockoutInstallation Checklist Mixing Valves IV Operating Instructions CautionRisk of scalding Hot water can produce third degree burnsLighting Instructions Robertshaw Heater Shutdown System Error CodesGas Control/Thermostat Lighting Instructions White-Rodgers Approximately 21C 70F when shipped from factory Temperature AdjustmentControl is adjusted to its lowest temperature setting Symptom Possible Causes Corrective Action Intelli-VentTMSystem Error Codes Heater ShutdownSymptom Possible Causes Corrective Action Operation Burner Flames VI MaintenanceOperational Conditions Draining and FlushingGas Control Anode Rod ReplacementRoutine Preventative Maintenance Blower Maintenance VII Combo Heating InstallationSystem Requirements Tice such as Ashrae Handbooks, HraiRobertshaw 2000WDER and White-Rodgers Intelli-VentTM Viii Troubleshooting GuideInterchangeable Items not supplied with the water heater Reference Parts ListingIX Reference Parts Robertshaw and White-Rodgers systems are not Interchangeable Parts Reference IllustrationWHO is Covered Limited WarrantyHOW the Original Owner can Make a Warranty Claim