Integra DTR-8.3 Connecting the remote zone Zone 2 speakers, When using the Zone 2 OUT terminals

Page 26

Connecting the remote zone (Zone 2) speakers

The DTR-8.3 allows you to watch and listen to two separate input sources at the same time. This allows you to, for example, place speakers and a television in two different rooms so that two or more people can enjoy two different movies at the same time. The room where the DTR-8.3 is actually located is referred to as the main room while the separate room is referred to as the remote zone (Zone 2). In addition, the IR IN/OUT terminal of the DTR-8.3 allows you to control the DTR-8.3 from the remote zone (Zone 2) with the remote controller even though the remote zone is physically separated. The diagram below shows how to make the proper connections for the

When using the SURR BACK/ZONE 2 SPEAKERS terminals

If you are using a 5.1-channel speaker system in the main room, you can connect the speakers for the remote zone (Zone 2) to the open SURR BACK/ZONE 2 SPEAKERS terminals.

With this connection, select “Zone 2” for the Hardware Setup → Surr Back/Zone 2 → Surr Back/Zone 2 setting in the Setup menu.

remote zone.

When using the ZONE 2 OUT terminals

When you have connected all the speakers for 7.1-channel audio in the main room, connect the speakers as shown below.

The ZONE 2 OUT terminal is a constant output. Connect to the LINE input of the amplifier (CD, tape, etc.). Adjust the volume with the amplifier connected to the ZONE 2 OUT terminal.

1.Connect the DTR-8.3 to the amplifier for the remote zone.

2.Connect the remote zone speaker cables to the speaker terminals on the amplifier.

3.Connect the DTR-8.3 to the monitor for the remote zone.

Main Room

SURR

BACK/

ZONE 2

SPEAKERS

RL

DTR-8.3

Note:

Remote Zone (Zone 2)

Zone 2

 

Zone 2

Left

 

Right

speaker

speaker

 

 

 

 

 

 

 

 

Remote Zone (Zone 2)

Zone 2

Zone 2 monitor

 

Zone 2

Left speaker

or projector

Right speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 2 amplifier

It is important to be aware of the speaker impedance (see page 23).

When using the SURR BACK/ZONE 2 PRE OUT terminals

If you are using a 5.1-channel speaker system in the main room, you can connect the amplifier for the remote zone (Zone 2) to the open SURR BACK/ZONE 2 PRE OUT terminals and connect the remote zone speakers.

With this connection, select “Zone 2” for the Hardware Setup → Surr Back/Zone 2 → Surr Back/Zone 2 setting in the Setup menu.

 

Main Room

AUDIO

VIDEO S VIDEO

 

MONITOR

 

OUT

R L

 

OUT

ZONE 2

Right (red)

 

Left (white)

DTR-8.3

Note:

The ZONE 2 out terminals of the DTR-8.3 are of a fixed output level.

Main Room

PRE OUT

R L

FRONT

SUBCENTER

SURR

SURR

BACK/ R L

ZONE 2

Left (white)

Remote Zone (Zone 2)

Zone 2

Zone 2

 

Left

 

Right

speaker

speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power amplifier

DTR-8.3

Right (red)

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents DTR-8.3 Important Safeguards AvisPrecautions Contents Contents Audio/Video Features FeaturesAmplifier Features FM/AM Tuner FeaturesConnecting the power cord Supplied accessoriesBefore using this unit Direct-access buttons Setting up the remote controllerCharacterizing the remote controller Serial port Reset button Battery coverComponent’s control panel Setting up the remote controllerHome menu Touch the screen to startFront door Index parts and facilitiesFront panels Index parts and facilities Front panel display Rear panels AV Amp Select AV Amp on the Home menu page 1/4 2/4 3/4 4/4 Remote controllerHome menu Light button Listening mode buttons+/- buttons AV amp buttonRear optical jack Connecting to Audio/Video equipmentImproper connection Inserted completely Coaxial cableConnecting a compact disc player CD Connecting to Audio/Video equipmentConnecting your audio components Connecting a turntable PhonoFlow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connecting a DVD player DVDConnecting a television monitor or projector Monitor OUT Monitor OUTSignal flow Connecting video camera, etc. Video 5 Input Minimum speaker configuration for surround sound playback Connecting speakersIdeal speaker configuration Speaker placementUsing the speaker labels Connecting speakersConnecting speakers Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageWhen using the Zone 2 OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Surr BACK/ZONE 2 Speakers terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsRemote controller Cabinet Signal flow ConnectingFrom connecting block Mini plug cable Block DTR-8.3 IR Emitter Remote controllerMiscellaneous Connections Connections for remote controlConnecting the power cords from other devices RS 232 portConnecting to an external device with 12V Trigger terminal Connecting to devices with analog multi channel outputConnecting auxiliary power amplifier Miscellaneous ConnectionsTurning on the power from the remote controller Connecting the powerTurning on the power To change the display of the input source from Tape to MDEnjoying music or videos with the DTR-8.3 Input source buttons Master VolumeDTR-8.3 Remote controller Basic operationEnjoying music or videos with the DTR-8.3 Changing the listening modeRemote controller only Listening with headphones Switching the displayAdjusting the bass and treble Temporarily turning off the soundTemporarily changing the speaker output levels Adjusting the brightness of the front displayUsing the sleep time remote controller only DimChanging the audio mode Enjoying the multichannel outputListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Erasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsStart recording at the recording component as desired Recording a sourceRec Out Press the Rec Out buttonRecording a source Zone 2 indicator Off Input source buttons Using the buttons on the DTR-8.3Ex. When the CD button is pressed Enjoying music or videos in the remote zoneEnjoying music or videos in the remote zone Selecting an input source using the remote controllerAdjusting the volume for the remote zone Advanced Menu Setup MenuBasic Menu When using the buttons on the front panel Setup MenuNavigating through the Setup Menu Button on remote controllerSpeaker Impedance Sub-menu Hardware SetupHardware Setup Menu Surr Back/Zone 2 Sub-menu Hardware SetupIR in Setup Sub-menu Surr Back/ZoneSpeaker Config Sub-menu Speaker SetupSpeaker Setup Menu Speaker Setup Speaker Distance Sub-menuCalibrating the speaker levels Press the Test button to complete the procedure CH SelLevel Calibration Sub-menu Press the Test buttonInitial settings for each input source Input SetupInput Setup Menu When NET Audio is not selected as the input sourceInput source selected Multichannel Input SetupDigital Format Video Setup Sub-menu Character Input Sub-menuTrigger Setup sub-menu IntelliVolume Sub-menuListening Mode Preset Sub-menu Type of software Relationship between input source and listening modeListening Mode Input source signals Listening ModesDigital Signal Processing DSP modes Setting Values Initial value Audio AdjustAudio Adjust Menu Tone Control Sub-menuSound Effect Sub-menu Audio AdjustDelay Sub-menu Mono Sub-menu Theater-Dimensional Sub-menuLFE Level Sub-menu Surround Sub-menu THX Sub-menu Bass Setting Tone ControlListening mode Treble Re-EQPreference Menu Volume Setup Sub-menuPreference Preference Headphones Level Sub-menuOSD Setup Sub-menu OSD Position Sub-menuUsing the Remote Controller Adjust the SettingsTo hide the Mode menu Using the Remote ControllerTap the mode you want to use Working with ModesSelecting a Device Select Yes to define the brand of the device to operate Define the Brand ofYour DeviceSelect a device in the Home menu Tap NextSelect a code set from the list Define the Brand of Your DeviceSelect your brand from the list Tap Search Tap OK when the device reactsDefining brands by searching To 8 inches 15 to 20 cm Programming ButtonsProgramming control panel buttons Programming device items Programming direct-access and Left/Right ButtonsProgramming Buttons Make sure the device tab is activeLabeling a menu item Labeling Buttons and Menu ItemsLabeling a button Edit the labelAdding macros Adding and Moving DevicesAdding devices Moving menu items Tap the item you want to restore Delete and restoreRestore DeleteEditing macros Recording Macros and SettingTimersRecording macros Organizing macros and timers into groups Recording Macros and Setting TimersSetting timers Tap RF Changing the remote controller’s RF IR SettingsSwitch to RF IR mode by using the Mode button Choosing Another Channel Optional recharging dock USA and Canadian models only Additional informationChadEdit With ChadEdit you canHow do I reset the Remote controller? Can I program a button to execute more than one command?How do I program source switching? How do I revert to the original configuration?Overview of Symbols Troubleshooting guide Troubleshooting guide Video and AudioRemote controller will not edit, label or delete commands General Problems Display is blankRemote controller shuts itself off Remote controller will not switch modesIf one of the messages shown below appears Total harmonic distortion SpecificationsAll channels Than 0 % total harmonicSpecifications Onkyo U.S.A. Corporation Internet radio features Net-Tune FeaturesConnecting the DTR-8.3 to your Ethernet Network Enjoying Internet radio Playing a music file saved on the Audio Network Server Use the / buttons to select one of the menu Using the Alphanumeric keysTo cancel the operation Net a Select NetA on the Home menu 1/3 2/3Configuring Various Settings Network Setup MenuIP Address Sub-menu Configuring Various SettingsProxy Setup Sub-menu MAC Address Sub-menuAppendix Troubleshooting guideSpecifications

DTR-8.3 specifications

The Integra DTR-8.3 is a sophisticated home theater receiver that exemplifies cutting-edge audio and video technologies, delivering an immersive experience for audiophiles and home cinema enthusiasts alike. As a flagship component in Integra's lineup, the DTR-8.3 combines high performance with versatile connectivity options, making it an ideal choice for modern entertainment systems.

One of the standout features of the DTR-8.3 is its robust power amplification, capable of delivering up to 100 watts per channel across nine channels. This level of power ensures dynamic sound reproduction across a wide range of audio formats, from the subtle nuances of a classical symphony to the thunderous effects of an action-packed movie. The receiver supports DTS:X and Dolby Atmos, providing object-based audio that envelops listeners in a three-dimensional soundstage. This technology enhances the overall cinematic experience, allowing sound to move freely around the listener, simulating a real-world environment.

In addition to its exemplary audio capabilities, the Integra DTR-8.3 is equipped with a full suite of video technologies. Supporting 4K Ultra HD resolution, HDR10, Dolby Vision, and BT.2020 color space, it is designed to handle the latest in high-definition video content. With full HDCP 2.2 support, users can connect their 4K Blu-ray players, gaming consoles, and streaming devices without worry. The receiver also features advanced video upscaling, transforming standard and high-definition video to near 4K quality for an enhanced viewing experience.

Connectivity is another area where the DTR-8.3 shines, with multiple HDMI inputs and outputs, including Zone 2 output for multi-room audio-video distribution. Users can easily integrate various sources, such as streaming devices, gaming consoles, and sound systems into their setup. Integrated Wi-Fi and Bluetooth capabilities enable seamless streaming of music from smartphones and tablets, while streaming services like Spotify, Pandora, and Amazon Music can be accessed directly.

The DTR-8.3 also embraces smart home integration, featuring compatibility with control systems such as Crestron, Control4, and others. This allows for easy automation and control of the receiver within a broader smart home ecosystem. For easy setup and configuration, the receiver comes with Audyssey MultEQ XT32 room correction technology. This feature analyzes the room acoustics and adjusts the sound output accordingly, ensuring optimal audio performance regardless of room conditions.

Overall, the Integra DTR-8.3 stands out as a premium home theater receiver, blending powerful audio performance, advanced video technologies, and intelligent connectivity options. It is designed for those who demand the best in their home entertainment experience, offering a truly immersive solution suitable for a wide range of applications. Whether you’re watching movies, listening to music, or gaming, the DTR-8.3 elevates sound and picture quality to new heights.
Top Page Image Contents