Integra DTR-8.3 Specifications, All channels, Total harmonic distortion, Than 0 % total harmonic

Page 86

Specifications

AMPLIFIER SECTION

Continuous average power output (FTC)

All channels:

110 W per channel min. RMS at 8

 

Ω, 2 channels driven from 20 Hz to

 

20 kHz with no more than 0.08%

 

total harmonic distortion.

 

145 W min. RMS at 6 Ω, 2 channels

 

driven from 1 kHz with no more

 

than 0 . 1% total harmonic

 

distortion.

Continuous power output (DIN)

150 W at 6 Ω

Maximum power output (EIAJ)

180 W at 6 Ω

Dynamic power output (stereo)

2 ⋅ 280 W at 3 Ω

 

2 ⋅ 220 W at 4 Ω

 

2 ⋅ 140 W at 8 Ω

Total Harmonic Distortion:

0.08% at rated power

 

0.08% at 1 W output

IM Distortion:

0.08% at rated power

 

0.08% at 1 W output

Damping factor:

60 at 8 Ω

Input sensitivity and impedance

2.5 mV, 50 kΩ

PHONO:

LINE (CD, TAPE, DVD,

200 mV, 50 kΩ

VIDEO 1-5):

MULTICHANNEL INPUT

 

(FRONT L/C/R, SURROUND

200 mV, 50 kΩ

L/R, SURROUND BACK L/R):

(SUBWOOFER):

36 mV, 50 kΩ

COAXIAL 1, 2, 3 (DIGITAL):

0.5 Vp-p, 75 Ω

DVD, VIDEO 1, 2, 3, 4, 5:

1 Vp-p, 75 Ω

 

1 Vp-p, 75 Ω (Y)

 

0.28 Vp-p, 75 Ω (C)

COMPONENT VIDEO 1, 2:

1 Vp-p, 75 Ω (Y)

 

0.7 Vp-p, 75 Ω (PB, PR)

Output level and impedance

 

Rec out (TAPE, VIDEO 1, 2):

200 mV, 470 Ω

 

Pre out:

1 V, 470 Ω

ZONE 2 OUT:

100 mV, 470 Ω

VIDEO (VIDEO 1, 2, MONITOR

OUT, ZONE 2 OUT):

1 Vp-p, 75 Ω

S-VIDEO (VIDEO 1, 2, MONITOR

OUT):

1 Vp-p, 75 Ω (Y)

 

0.28 p-p, 75 Ω (C)

COMPONENT VIDEO OUT:

1 Vp-p, 75 Ω (Y)

 

0.7 Vp-p, 75 Ω (PB, PR)

Phono overload:

120 mV RMS at 1 kHz, 0.5% T.H.D.

Frequency response:

5 Hz to 100 kHz : +1/–3 dB

 

(CD in Direct mode)

RIAA deviation:

20 Hz to 20 kHz : ±0.8 dB

Tone Control

 

Bass:

±10 dB at 50 Hz

Treble:

±10 dB at 20,000 Hz

Signal-to-noise ratio (direct)

 

Phono:

80 dB (IHF A, 5 mV input)

CD/Tape:

110 dB (IHF A, 0.5 V input)

TUNER SECTION

 

FM

 

Tuning range

 

USA & Canadian models:

87.50–108.00 MHz (100-kHz steps)

Australian models:

87.50–108.00 MHz (50-kHz steps)

Usable sensitivity

11.2 dBf, 1.0 µV (75 Ω IHF)

Mono:

 

0.9 µV (75 Ω DIN)

Stereo:

17.2 dBf, 2.0 µV (75 Ω IHF)

 

23 µV (75 Ω DIN)

50 dB quieting sensitivity

17.2 dBf, 2.0 µV (75 Ω)

Mono:

Stereo:

37.2 dBf, 20 µV (75 Ω)

Capture ratio:

2.0 dB

Image rejection ratio

 

USA & Canadian models:

40 dB

Australian models:

85 dB

IF rejection ratio:

90 dB

Signal-to-noise ratio

 

Mono:

76 dB

Stereo:

70 dB

Alternate channel attenuation:

55 dB

Selectivity:

50 dB (DIN)

AM suppression ratio:

50 dB

Total harmonic distortion

 

Mono:

0.2%

Stereo:

0.3%

Frequency response:

30 Hz–15 kHz, ±1.0 dB

Stereo separation:

45 dB at 1 kHz

AM

30 dB at 100 Hz–10 kHz

 

Tuning range

 

USA & Canadian models:

530 to 1,710kHz (10kHz steps)

Australian models:

522 to 1,611 kHz (9-kHz steps)

Usable sensitivity:

30 µV

Image rejection ratio:

40 dB

IF rejection ratio:

40 dB

Signal-to-noise ratio:

40 dB

Total harmonic distortion:

0.7%

GENERAL

 

Power supply

 

USA & Canadian models:

AC 120 V, 60 Hz

Australian models:

AC 230–240 V, 50 Hz

Power consumption

 

USA & Canadian models:

8.4 A

Australian models:

670 W

Dimensions (W ⋅ H ⋅ D):

435 ⋅ 175 ⋅ 460 mm

 

17-1/8" ⋅ 6-7/8" ⋅ 18-1/8"

Weight

 

 

18.2 kg (40.1 lbs)

Specifications and features are subject to change without notice.

86

Page 85 Page 87
Image 86
Page 85 Page 87
Contents DTR-8.3 Important Safeguards AvisPrecautions Contents Contents Audio/Video Features FeaturesAmplifier Features FM/AM Tuner FeaturesConnecting the power cord Supplied accessoriesBefore using this unit Direct-access buttons Setting up the remote controllerCharacterizing the remote controller Serial port Reset button Battery coverComponent’s control panel Setting up the remote controllerHome menu Touch the screen to startFront door Index parts and facilitiesFront panels Index parts and facilities Front panel display Rear panels AV Amp Select AV Amp on the Home menu page 1/4 2/4 3/4 4/4 Remote controllerHome menu Light button Listening mode buttons+/- buttons AV amp buttonRear optical jack Connecting to Audio/Video equipmentImproper connection Inserted completely Coaxial cableConnecting a compact disc player CD Connecting to Audio/Video equipmentConnecting your audio components Connecting a turntable PhonoFlow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connecting a DVD player DVDConnecting a television monitor or projector Monitor OUT Monitor OUTSignal flow Connecting video camera, etc. Video 5 Input Minimum speaker configuration for surround sound playback Connecting speakersIdeal speaker configuration Speaker placementUsing the speaker labels Connecting speakersConnecting speakers Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageWhen using the Zone 2 OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Surr BACK/ZONE 2 Speakers terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsRemote controller Cabinet Signal flow ConnectingFrom connecting block Mini plug cable Block DTR-8.3 IR Emitter Remote controllerMiscellaneous Connections Connections for remote controlConnecting the power cords from other devices RS 232 portConnecting to an external device with 12V Trigger terminal Connecting to devices with analog multi channel outputConnecting auxiliary power amplifier Miscellaneous ConnectionsTurning on the power from the remote controller Connecting the powerTurning on the power To change the display of the input source from Tape to MDEnjoying music or videos with the DTR-8.3 Input source buttons Master VolumeDTR-8.3 Remote controller Basic operationEnjoying music or videos with the DTR-8.3 Changing the listening modeRemote controller only Listening with headphones Switching the displayAdjusting the bass and treble Temporarily turning off the soundTemporarily changing the speaker output levels Adjusting the brightness of the front displayUsing the sleep time remote controller only DimChanging the audio mode Enjoying the multichannel outputListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Erasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsStart recording at the recording component as desired Recording a sourceRec Out Press the Rec Out buttonRecording a source Zone 2 indicator Off Input source buttons Using the buttons on the DTR-8.3Ex. When the CD button is pressed Enjoying music or videos in the remote zoneEnjoying music or videos in the remote zone Selecting an input source using the remote controllerAdjusting the volume for the remote zone Advanced Menu Setup MenuBasic Menu When using the buttons on the front panel Setup MenuNavigating through the Setup Menu Button on remote controllerSpeaker Impedance Sub-menu Hardware SetupHardware Setup Menu Surr Back/Zone 2 Sub-menu Hardware SetupIR in Setup Sub-menu Surr Back/ZoneSpeaker Config Sub-menu Speaker SetupSpeaker Setup Menu Speaker Setup Speaker Distance Sub-menuCalibrating the speaker levels Press the Test button to complete the procedure CH SelLevel Calibration Sub-menu Press the Test buttonInitial settings for each input source Input SetupInput Setup Menu When NET Audio is not selected as the input sourceInput source selected Multichannel Input SetupDigital Format Video Setup Sub-menu Character Input Sub-menuTrigger Setup sub-menu IntelliVolume Sub-menuListening Mode Preset Sub-menu Type of software Relationship between input source and listening modeListening Mode Input source signals Listening ModesDigital Signal Processing DSP modes Setting Values Initial value Audio AdjustAudio Adjust Menu Tone Control Sub-menuSound Effect Sub-menu Audio AdjustDelay Sub-menu Mono Sub-menu Theater-Dimensional Sub-menuLFE Level Sub-menu Surround Sub-menu THX Sub-menu Bass Setting Tone ControlListening mode Treble Re-EQPreference Menu Volume Setup Sub-menuPreference Preference Headphones Level Sub-menuOSD Setup Sub-menu OSD Position Sub-menuUsing the Remote Controller Adjust the SettingsTo hide the Mode menu Using the Remote ControllerTap the mode you want to use Working with ModesSelecting a Device Select Yes to define the brand of the device to operate Define the Brand ofYour DeviceSelect a device in the Home menu Tap NextSelect a code set from the list Define the Brand of Your DeviceSelect your brand from the list Tap Search Tap OK when the device reactsDefining brands by searching To 8 inches 15 to 20 cm Programming ButtonsProgramming control panel buttons Programming device items Programming direct-access and Left/Right ButtonsProgramming Buttons Make sure the device tab is activeLabeling a menu item Labeling Buttons and Menu ItemsLabeling a button Edit the labelAdding macros Adding and Moving DevicesAdding devices Moving menu items Tap the item you want to restore Delete and restoreRestore DeleteEditing macros Recording Macros and SettingTimersRecording macros Organizing macros and timers into groups Recording Macros and Setting TimersSetting timers Tap RF Changing the remote controller’s RF IR SettingsSwitch to RF IR mode by using the Mode button Choosing Another Channel Optional recharging dock USA and Canadian models only Additional informationChadEdit With ChadEdit you canHow do I reset the Remote controller? Can I program a button to execute more than one command?How do I program source switching? How do I revert to the original configuration?Overview of Symbols Troubleshooting guide Troubleshooting guide Video and AudioRemote controller will not edit, label or delete commands General Problems Display is blankRemote controller shuts itself off Remote controller will not switch modesIf one of the messages shown below appears Total harmonic distortion SpecificationsAll channels Than 0 % total harmonicSpecifications Onkyo U.S.A. Corporation Internet radio features Net-Tune FeaturesConnecting the DTR-8.3 to your Ethernet Network Enjoying Internet radio Playing a music file saved on the Audio Network Server Use the / buttons to select one of the menu Using the Alphanumeric keysTo cancel the operation Net a Select NetA on the Home menu 1/3 2/3Configuring Various Settings Network Setup MenuIP Address Sub-menu Configuring Various SettingsProxy Setup Sub-menu MAC Address Sub-menuAppendix Troubleshooting guideSpecifications

DTR-8.3 specifications

The Integra DTR-8.3 is a sophisticated home theater receiver that exemplifies cutting-edge audio and video technologies, delivering an immersive experience for audiophiles and home cinema enthusiasts alike. As a flagship component in Integra's lineup, the DTR-8.3 combines high performance with versatile connectivity options, making it an ideal choice for modern entertainment systems.

One of the standout features of the DTR-8.3 is its robust power amplification, capable of delivering up to 100 watts per channel across nine channels. This level of power ensures dynamic sound reproduction across a wide range of audio formats, from the subtle nuances of a classical symphony to the thunderous effects of an action-packed movie. The receiver supports DTS:X and Dolby Atmos, providing object-based audio that envelops listeners in a three-dimensional soundstage. This technology enhances the overall cinematic experience, allowing sound to move freely around the listener, simulating a real-world environment.

In addition to its exemplary audio capabilities, the Integra DTR-8.3 is equipped with a full suite of video technologies. Supporting 4K Ultra HD resolution, HDR10, Dolby Vision, and BT.2020 color space, it is designed to handle the latest in high-definition video content. With full HDCP 2.2 support, users can connect their 4K Blu-ray players, gaming consoles, and streaming devices without worry. The receiver also features advanced video upscaling, transforming standard and high-definition video to near 4K quality for an enhanced viewing experience.

Connectivity is another area where the DTR-8.3 shines, with multiple HDMI inputs and outputs, including Zone 2 output for multi-room audio-video distribution. Users can easily integrate various sources, such as streaming devices, gaming consoles, and sound systems into their setup. Integrated Wi-Fi and Bluetooth capabilities enable seamless streaming of music from smartphones and tablets, while streaming services like Spotify, Pandora, and Amazon Music can be accessed directly.

The DTR-8.3 also embraces smart home integration, featuring compatibility with control systems such as Crestron, Control4, and others. This allows for easy automation and control of the receiver within a broader smart home ecosystem. For easy setup and configuration, the receiver comes with Audyssey MultEQ XT32 room correction technology. This feature analyzes the room acoustics and adjusts the sound output accordingly, ensuring optimal audio performance regardless of room conditions.

Overall, the Integra DTR-8.3 stands out as a premium home theater receiver, blending powerful audio performance, advanced video technologies, and intelligent connectivity options. It is designed for those who demand the best in their home entertainment experience, offering a truly immersive solution suitable for a wide range of applications. Whether you’re watching movies, listening to music, or gaming, the DTR-8.3 elevates sound and picture quality to new heights.
Top Page Image Contents