Integra instruction manual Connecting the DTR-8.3 to your Ethernet Network

Page 90

Connecting the DTR-8.3 to your Ethernet Network

Plug one end of an Ethernet CAT-5 cable into the port on the backside of the DTR-8.3 and the other end into the gateway.

 

Internet

 

LAN port/

 

Ethernet, etc

 

Audio Network

Modem

Server

 

To the WAN side

 

To the LAN

 

side port

 

To the LAN side port

COMPONENT

 

 

 

 

 

VIDEO

FRONT SPEAKERS

SURR SPEAKERS

 

OUTPUT

R

L

R

L

AV RECEIVER

Y

MODEL NO. DTR-8.3

 

 

 

 

RATING: AC 120V 60 Hz 8.4A

PB

 

 

 

 

 

 

AC OUTLETS

P

 

 

 

INPUT 1

 

 

 

Y

ETHERNET

 

 

 

 

 

 

[NET-TUNE]

 

 

 

CENTER

SURR

 

PB

BACK/

 

 

SPEAKER

ZONE 2

 

 

CAUTION:

SPEAKERS

AC 120V 60 Hz

 

SPEAKER

 

SWITCHED

 

TOTAL 120W 1A MAX.

PR

IMPEDANCE

 

 

 

4 OHMS MIN. OR

 

R

 

L

INPUT 2

6 OHMS MIN.

 

 

 

 

/SPEAKER

 

 

 

 

Y

SEE INSTRUCTION

I R

 

 

AC INLET

 

A

ZONE 2

 

MANUAL FOR

 

 

 

CORRECT SETTINGS.

 

 

12V

 

 

IN

 

TRIGGER OUT

 

 

 

 

 

PB

 

RS232

 

 

 

PR

 

 

B

 

 

 

 

OUT

REMOTE

 

 

 

 

 

CONTROL

 

Router

DTR-8.3

Internet radio

Hint:

Connecting more than one unit of DTR-8.3 to a router enables several users to listen to Internet radio at different stations or different music pieces contained in the same library on the Audio Network Server.

 

Audio Network

Modem

Server

 

To the WAN side

 

 

To the LAN side port

 

To the LAN side port

Router

To the LAN side port

Room 1

Room 2

2

Page 89 Page 91
Image 90
Page 89 Page 91
Contents DTR-8.3 Important Safeguards AvisPrecautions Contents Contents Audio/Video Features FeaturesAmplifier Features FM/AM Tuner FeaturesSupplied accessories Before using this unitConnecting the power cord Direct-access buttons Setting up the remote controllerCharacterizing the remote controller Serial port Reset button Battery coverComponent’s control panel Setting up the remote controllerHome menu Touch the screen to startIndex parts and facilities Front panelsFront door Index parts and facilities Front panel display Rear panels Remote controller Home menuAV Amp Select AV Amp on the Home menu page 1/4 2/4 3/4 4/4 Light button Listening mode buttons+/- buttons AV amp buttonRear optical jack Connecting to Audio/Video equipmentImproper connection Inserted completely Coaxial cableConnecting a compact disc player CD Connecting to Audio/Video equipmentConnecting your audio components Connecting a turntable PhonoFlow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connecting a DVD player DVDConnecting a television monitor or projector Monitor OUT Monitor OUTSignal flow Connecting video camera, etc. Video 5 Input Minimum speaker configuration for surround sound playback Connecting speakersIdeal speaker configuration Speaker placementConnecting speakers Connecting speakersUsing the speaker labels Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageWhen using the Zone 2 OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Surr BACK/ZONE 2 Speakers terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsRemote controller Cabinet Signal flow ConnectingFrom connecting block Mini plug cable Block DTR-8.3 IR Emitter Remote controllerMiscellaneous Connections Connections for remote controlConnecting the power cords from other devices RS 232 portConnecting to an external device with 12V Trigger terminal Connecting to devices with analog multi channel outputConnecting auxiliary power amplifier Miscellaneous ConnectionsTurning on the power from the remote controller Connecting the powerTurning on the power To change the display of the input source from Tape to MDEnjoying music or videos with the DTR-8.3 Input source buttons Master VolumeDTR-8.3 Remote controller Basic operationChanging the listening mode Remote controller onlyEnjoying music or videos with the DTR-8.3 Listening with headphones Switching the displayAdjusting the bass and treble Temporarily turning off the soundTemporarily changing the speaker output levels Adjusting the brightness of the front displayUsing the sleep time remote controller only DimChanging the audio mode Enjoying the multichannel outputTuning into a radio station Listening to a stereo radio station FM modeListening to Radio Broadcasts Erasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsStart recording at the recording component as desired Recording a sourceRec Out Press the Rec Out buttonRecording a source Zone 2 indicator Off Input source buttons Using the buttons on the DTR-8.3Ex. When the CD button is pressed Enjoying music or videos in the remote zoneSelecting an input source using the remote controller Adjusting the volume for the remote zoneEnjoying music or videos in the remote zone Setup Menu Basic MenuAdvanced Menu When using the buttons on the front panel Setup MenuNavigating through the Setup Menu Button on remote controllerHardware Setup Hardware Setup MenuSpeaker Impedance Sub-menu Surr Back/Zone 2 Sub-menu Hardware SetupIR in Setup Sub-menu Surr Back/ZoneSpeaker Setup Speaker Setup MenuSpeaker Config Sub-menu Speaker Setup Speaker Distance Sub-menuCalibrating the speaker levels Press the Test button to complete the procedure CH SelLevel Calibration Sub-menu Press the Test buttonInitial settings for each input source Input SetupInput Setup Menu When NET Audio is not selected as the input sourceInput Setup Digital FormatInput source selected Multichannel Video Setup Sub-menu Character Input Sub-menuIntelliVolume Sub-menu Listening Mode Preset Sub-menuTrigger Setup sub-menu Relationship between input source and listening mode Listening ModeType of software Input source signals Listening ModesDigital Signal Processing DSP modes Setting Values Initial value Audio AdjustAudio Adjust Menu Tone Control Sub-menuAudio Adjust Delay Sub-menuSound Effect Sub-menu Theater-Dimensional Sub-menu LFE Level Sub-menuMono Sub-menu Surround Sub-menu THX Sub-menu Bass Setting Tone ControlListening mode Treble Re-EQVolume Setup Sub-menu PreferencePreference Menu Preference Headphones Level Sub-menuOSD Setup Sub-menu OSD Position Sub-menuUsing the Remote Controller Adjust the SettingsTo hide the Mode menu Using the Remote ControllerTap the mode you want to use Working with ModesSelecting a Device Select Yes to define the brand of the device to operate Define the Brand ofYour DeviceSelect a device in the Home menu Tap NextDefine the Brand of Your Device Select your brand from the listSelect a code set from the list Tap OK when the device reacts Defining brands by searchingTap Search Programming Buttons Programming control panel buttonsTo 8 inches 15 to 20 cm Programming device items Programming direct-access and Left/Right ButtonsProgramming Buttons Make sure the device tab is activeLabeling a menu item Labeling Buttons and Menu ItemsLabeling a button Edit the labelAdding and Moving Devices Adding devices Moving menu itemsAdding macros Tap the item you want to restore Delete and restoreRestore DeleteRecording Macros and SettingTimers Recording macrosEditing macros Recording Macros and Setting Timers Setting timersOrganizing macros and timers into groups Changing the remote controller’s RF IR Settings Switch to RF IR mode by using the Mode buttonTap RF Choosing Another Channel Optional recharging dock USA and Canadian models only Additional informationChadEdit With ChadEdit you canHow do I reset the Remote controller? Can I program a button to execute more than one command?How do I program source switching? How do I revert to the original configuration?Overview of Symbols Troubleshooting guide Troubleshooting guide Video and AudioRemote controller will not edit, label or delete commands General Problems Display is blankRemote controller shuts itself off Remote controller will not switch modesIf one of the messages shown below appears Total harmonic distortion SpecificationsAll channels Than 0 % total harmonicSpecifications Onkyo U.S.A. Corporation Internet radio features Net-Tune FeaturesConnecting the DTR-8.3 to your Ethernet Network Enjoying Internet radio Playing a music file saved on the Audio Network Server Use the / buttons to select one of the menu Using the Alphanumeric keysTo cancel the operation Net a Select NetA on the Home menu 1/3 2/3Configuring Various Settings Network Setup MenuIP Address Sub-menu Configuring Various SettingsProxy Setup Sub-menu MAC Address Sub-menuTroubleshooting guide SpecificationsAppendix

DTR-8.3 specifications

The Integra DTR-8.3 is a sophisticated home theater receiver that exemplifies cutting-edge audio and video technologies, delivering an immersive experience for audiophiles and home cinema enthusiasts alike. As a flagship component in Integra's lineup, the DTR-8.3 combines high performance with versatile connectivity options, making it an ideal choice for modern entertainment systems.

One of the standout features of the DTR-8.3 is its robust power amplification, capable of delivering up to 100 watts per channel across nine channels. This level of power ensures dynamic sound reproduction across a wide range of audio formats, from the subtle nuances of a classical symphony to the thunderous effects of an action-packed movie. The receiver supports DTS:X and Dolby Atmos, providing object-based audio that envelops listeners in a three-dimensional soundstage. This technology enhances the overall cinematic experience, allowing sound to move freely around the listener, simulating a real-world environment.

In addition to its exemplary audio capabilities, the Integra DTR-8.3 is equipped with a full suite of video technologies. Supporting 4K Ultra HD resolution, HDR10, Dolby Vision, and BT.2020 color space, it is designed to handle the latest in high-definition video content. With full HDCP 2.2 support, users can connect their 4K Blu-ray players, gaming consoles, and streaming devices without worry. The receiver also features advanced video upscaling, transforming standard and high-definition video to near 4K quality for an enhanced viewing experience.

Connectivity is another area where the DTR-8.3 shines, with multiple HDMI inputs and outputs, including Zone 2 output for multi-room audio-video distribution. Users can easily integrate various sources, such as streaming devices, gaming consoles, and sound systems into their setup. Integrated Wi-Fi and Bluetooth capabilities enable seamless streaming of music from smartphones and tablets, while streaming services like Spotify, Pandora, and Amazon Music can be accessed directly.

The DTR-8.3 also embraces smart home integration, featuring compatibility with control systems such as Crestron, Control4, and others. This allows for easy automation and control of the receiver within a broader smart home ecosystem. For easy setup and configuration, the receiver comes with Audyssey MultEQ XT32 room correction technology. This feature analyzes the room acoustics and adjusts the sound output accordingly, ensuring optimal audio performance regardless of room conditions.

Overall, the Integra DTR-8.3 stands out as a premium home theater receiver, blending powerful audio performance, advanced video technologies, and intelligent connectivity options. It is designed for those who demand the best in their home entertainment experience, offering a truly immersive solution suitable for a wide range of applications. Whether you’re watching movies, listening to music, or gaming, the DTR-8.3 elevates sound and picture quality to new heights.
Top Page Image Contents