Integra DTR-7.1 appendix Front panel facilities

Page 9

Front panel facilities

Front panel

Power switch

After plugging in the power cord into the rear panel and wall outlet, pressing this button connects the DTR-7.1 to the AC mains and turns it on.

•Before turning on the power, make sure all cables are properly connected.

•Turning on the DTR-7.1 may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the DTR-7.1 into a different electrical circuit.

Standby indicator

Lights when the DTR-7.1 is in the standby state and flashes when a signal is received from the remote controller.

Standby/On button

Pressing this button while the main power is turned on the Standby indicator lights up and the front display turns off. Pressing it again returns it to the standby state. This state turns off the display, disables control functions.

Phones jack

This is a standard stereo jack for connecting stereo headphones. The audio for the front right and left speakers are sent to the headphone speakers. When the headphones are plugged in, the listening mode automatically changes to stereo and output to the speakers is stopped.

Audio Selector button

This button is used to select the type of audio input signal. Each time pressed, the setting cycles from “AUTO” → “Multichannel”

→“Analog” and back.

AUTO (automatic detection): With this setting, the DTR-7.1 automatically detects whether the input signal is digital or analog. When a digital signal is not input, then the analog signal is played.

Multichannel: Select this setting to play back the input from the component connected to the MULTI CHANNEL INPUT port. This setting is effective when the Multichannel setting in the Audio Setup sub-menu is set to “Yes” (see page 35).

Analog: Select this setting to play back the input from a source component connected to an AUDIO IN jack. With this setting, even if a digital signal is input from the same component, only the analog signal will be output.

Zone 2 indicator

Lights when a signal is output to the remote zone (Zone 2). When the Zone 2 indicator is off, then either output to the remote zone is turned off or Rec Out is selected.

Rec Out/Zone 2 buttons

These buttons allow you to use the DTR-7.1 to output to a remote zone (Zone 2) or to another component for recording purposes (Rec Out). Press the Rec Out button to output the audio and video signals to a recording component for recording purposes. Press the Zone 2 button to enjoy the output from the DTR-7.1 in a different room, which is referred to as a remote zone (Zone 2).

When either button is pressed, the currently selected input source for recording or outputting to the remote zone is displayed in the front panel display. If “SOURCE” is displayed, then the same input source as that selected for the main zone will be output.

To select an input source, press the desired button (Rec Out or Zone 2) and then press one of the input source button within 3 seconds. That source will be output for recording or viewing in the remote zone. To turn off either the Rec Out or Zone 2 output, when “SOURCE” is displayed, press the button again. “OFF” appears in the front display.

Notes:

•The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time. When Rec Out is selected, nothing is output to Zone 2, and vice versa.

•When not using Rec Out or Zone 2, turn off the signal. If turned on and the connected component is not turned on, the electric signal will still be sent through the circuitry and the excess load may cause deterioration of the audio signal.

Master Volume dial

The Master Volume dial is used to control the volume for the main zone. The volume for the remote zone (Zone 2) is independent.

Input Source Buttons (DVD, Video 1–4, Tape, FM, AM, Phono, and CD)

These buttons are used to select the input source for the main zone. To select the input source for the remote zone (Zone 2) or recording out (Rec Out), first press the Zone 2 or Rec Out button, and then the desired input source button.

Video 4/Video Cam Input

These inputs are for connecting video cameras and other such equipment.

Dimmer button

Press to set the brightness of the front display. There are 3 settings available: normal, dark, and very dark.

•The dimmer control for the front display can also be performed at the remote controller.

Front display

FM Mute/Mode button

If you are listening to an FM radio station in stereo and the sound cuts out or there is a great deal of noise, switch from STEREO to MONO. Each time this button is pressed, the AUTO indication flashes and the stereo mode changes from AUTO to MONO and vice versa. This button also turns on and off the FM MUTE.

Tuning Up/Down button

Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display and it can be changed in 50 kHz increments for FM and 10 kHz (or 9 kHz) increments for AM.

When FM is selected, you can hold down one of the tuning buttons and then release it to activate the auto-search feature. It will search for a station in the direction of the button you pressed and stop when it tunes into one.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents DTR-7.1 Avis Important SafeguardsPrecautions Contents Contents Supplied accessoriesTHX Select FeaturesUsing the remote controller Before using this unitFront panel facilities Front panelFront panel display Front panel facilities Remote control sensor Menu button Listening Mode buttonsTuned indicator Auto indicator Multi function display Character/Memory buttonRemote controller Speaker Impedance Rear panel facilitiesDigital INPUT/OUTPUT coaxial and optical Rear panel facilitiesSpeakers 12V Trigger A, B terminals Video IN/OUTExample of how to connect your equipment Default setting Example of how to connect your equipmentPower amplifier See Standard connectionsConnecting a turntable Connecting your audio componentsConnecting a compact disc player Connecting your video componentsConnecting a satellite tuner or television Connecting video camera or television gameConnecting a television monitor or projector Ideal speaker configuration Connecting speakersMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersConnecting a subwoofer Connecting the AM loop antenna Connecting antennasAssembling the AM loop antenna HintConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageOutline Connecting to the remote zone Zone 2 inputConnecting to the remote zone Zone 2 input Connecting to the IR in Main inputWhen using the Zone 2 OUT terminals Main zone Remote zone ZoneConnecting two surround back speakers Connecting power amplifiers and two surround back speakersConnecting the power Connecting the powerTurning the power on from the remote controller On StnbyOn-Screen Display OSD menu On-Screen Display OSD menu Speaker Setup Speaker Setup menuSpeaker Config sub-menu Speaker Distance sub-menu Speaker SetupCalibrating the speaker levels Level Calibration sub-menuLeft RightBass Peak Level Bass Peak Level Manager* sub-menu Bass Peak Level LimiterBass Peak Level Input Setup menu Input SetupAudio Setup sub-menu Initial settings for each input sourceInput Setup Digital FormatMultichannel Video Setup sub-menu VideoComponent Input source signals Listening Mode Preset sub-menu2ch Source PCM fs=96kListening Modes Enhanced Theater-DimensionalOrchestra TV LogicIntelliVolume sub-menu Tone Control sub-menuTrigger sub-menu Listening Mode Setup menu Listening Mode SetupMono Movie Setup Listening Mode SetupEnhanced 7 Setup All Ch Stereo SetupDescription listening mode parameters Front Expander Listening angleVirtual Surr Level Dialog EnhancePreference OSD Setup menu OSD SetupOSD Config sub-menu OSD outputOSD Setup OSD Setup sub-menuOSD Position sub-menu Select a source Enjoying music in the remote zoneVOL SSCListening to Radio Broadcasts AUDIO/TAPE ModeListening to FM/AM Radio Stations TUNListening to Radio Broadcasts Press the SSC dial to finalize the procedureChanging the listening mode Adjusting the volumeListening with headphones Enjoying music or videos with the DTR-7.1Enjoying music or videos with the DTR-7.1 Using the many features of the DTR-7.1If one of the messages shown below appears Enjoying the multichannel inputStart recording at the recording component as Desired Recording a sourceRecording a source Characters available for name entry Giving a name to each preset radio stationUsing the remote controller to control each device Using remote controllerPress the AUDIO/TAPE Mode button OverviewUsing remote controller Press the MD Mode button Press the CD Mode buttonCD Mode Controlling an Integra/Onkyo CD playerPress the TUN input selector button Controlling an Integra/Onkyo cassette tape deckSAT, CABLE, VCR, and TV Mode buttons Press the DVD Mode buttonOn Stnby DVD Mode DVD SET Menu Controlling an Integra DVD playerDirect Mode Macro Programming procedureENT LightPage Erasing the programmed command from one button Press and release the same Mode button againPress and release the same button again What is a Macro function? Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionPress the Direct Macro button to complete the procedure Using a Macro functionProgramming the Direct Macro function Check to see if the macro has been properly programmedMode Macro Press the Mode Macro button againPress the Direct Macro button again Direct MacroOperation Press the ENT buttonTroubleshooting guide Troubleshooting guide Re-EQ function cannot be used Late Night function cannot be usedParameter cannot be set for Front Effect, Room Size, etc Multichannel audio is not outputAmplifier Section SpecificationsOnkyo U.S.A. Corporation

DTR-7.1 specifications

The Integra DTR-7.1 is a distinguished A/V receiver that exemplifies high-performance audio and video processing for home theater enthusiasts. Known for its meticulous engineering and robust feature set, the DTR-7.1 appeals to both audiophiles and casual viewers alike.

At the heart of the Integra DTR-7.1 lies a powerful amplification system that delivers 7.1 channels of immersive surround sound. With a substantial power output, the receiver ensures that even the most demanding soundtracks are reproduced with accuracy and clarity. The discrete power amplifier design contributes to lower distortion levels, providing a cleaner audio experience.

One of the standout features of the Integra DTR-7.1 is its advanced audio processing capabilities. It supports several high-definition formats, including Dolby TrueHD and DTS-HD Master Audio. This wide array of decoding options allows for a richly detailed auditory experience, especially when paired with high-definition media.

Moreover, the DTR-7.1 is equipped with cutting-edge video processing technology. It supports 4K and 1080p video resolutions, ensuring compatibility with the latest video formats. The integrated video scaling feature upscales lower-resolution content to near-4K quality, enhancing the viewing experience regardless of the source material.

Connectivity is another strong suit of the Integra DTR-7.1. The receiver boasts multiple HDMI inputs, facilitating easy connection to various devices such as Blu-ray players, gaming consoles, and streaming devices. Additionally, it supports features like ARC (Audio Return Channel) and CEC (Consumer Electronics Control), streamlining control and simplifying the setup process.

For ultimate customization, the DTR-7.1 includes an advanced auto-calibration system, which optimally adjusts sound settings based on the acoustics of the room and the speaker placement. This technology ensures that users achieve the best possible sound regardless of their home theater setup.

Finally, the Integra DTR-7.1 offers comprehensive network capabilities. It supports streaming services and internet radio, providing users with access to a vast library of music and content. Integration with home automation systems is also seamless, allowing users to control the receiver through smart devices for added convenience.

In summary, the Integra DTR-7.1 stands out as a top-tier A/V receiver, combining superior amplification, advanced audio and video processing, extensive connectivity options, and smart features, making it a worthy addition to any home theater system.
Top Page Image Contents