Furuno SC-110 manual Others Menu, Others menu, HDG Restoration options

Page 48

2. OPERATION

2.11OTHERS Menu

The OTHERS menu contains the following items:

HOLD HDG DATA: Choose whether to display last-used heading data at power on or not. Because this data is not reliable, the heading indication flashes to alert you.

HDG RESTORATION: Choose how to restore GPS signal, automatically or manually, after it is lost. For manual restoration, a key must be pressed to restart heading output. This is done for safety purposes; for example, when an autopilot is used.

HDG BACKUP: Choose how long to display backup data when the GPS signal is lost. (This data is also output to external equipment.)

1.Press the [MENU] key to display the main menu.

2.Choose OTHERS and then press the [ENT] key.

OTHERS

HOLD HDG DATA: OFF

HDG RESTORATION : MAN

HDG BACKUP : 5MIN

Others menu

3. HOLD HDG DATA is selected; press the [ENT] key.

OFF

ON

4.Choose ON or OFF as appropriate.

5.Press the [ENT] key.

6.HDG RESTORATION is selected; press the [ENT] key.

MAN

AUTO

HDG RESTORATION options

7.Use the Omnipad to choose MAN or AUTO as appropriate and then press the [ENT] key.

8.HDG BACKUP is selected; press the [ENT] key.

9.Choose 1, 2, 3, 4 or 5 minutes as appropriate.

10.Press the [ENT] key followed by the [DISP] key to close the menu.

2-20

Page 47 Page 49
Image 48
Page 47 Page 49
Contents THD Satellite Compass 00014854600 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures ForewordWord to the Owner of the SC-110 System Configuration System configurationEquipment List Standard supplyOptional equipment Name Type Code No Qty RemarksSpecifications of THD Satellite Compass SC-110Coating Color Installation Mounting ConsiderationsAntenna unit Mast diameter Separation distance minimum Separation degreesAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Unit Installation postFix the antenna unit to the post as shown below Fastening antenna unit to a postCoating bolt, nut and washer with silicone rubber Antenna elementInstalling the Processor Unit Bulkhead mountBulkhead mount Deck mount Processor unit orientation, deck mountingInstallation on the underside of a desk Installation of processor unit on the underside of a deskMounting on underside of desk Installing the Display Unit Desktop, overhead mountingFlush mount Flush mount FFlush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring WiringHow to install the optional antenna cable set Sectional view of coaxial cable DPYC-1.5How to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Confirming satellite statusSatellite tracking status display Installation setup menu Choosing mounting methodMain menu General wiring Connection of External EquipmentProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationOperation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Speed display SOG/STW displayAlarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Data OUT1 menu, sentences Baud rate optionsTx interval options IEC, Nmea version optionsHeading talker options Output sentence limitation Sentence and maximum number of charactersLog pulse Log pulse optionsSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation Others Menu Others menuHDG Restoration options Trip Menu Trip menuResetting Distance Run Choosing External Heading Source for BackupReset Distance prompt Heading setup menuMAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence Display Test Program Number DisplayDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsTEST3 menu Program Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRAppendix Menu TreeAP-1 Digital Interface Schematic diagrams AP-3Data Data OutData sentences AP-4AP-5 GNS Gnns fix dataAP-6 VBW Dual ground/water speedAP-7 VLW Distance travelled through the waterPort Terminal Name Signal Remarks Label Input/Output PortsAP-8 AP-9 HdthdghdmParts List and Parts Location AP-10Processor Unit, cover removed AP-11 Display Unit, cover openedGeodetic Chart Codes AP-12Principle of Satellite Compass AP-13What is WAAS? AP-14Ｐａｃｋｉｎｇ Ｌｉｓｔ Page 工事材料表 SC-502-J/E 20AY-X-9404 SC-1101-J/E 20AY-X-9401 Spare Parts List for 20AT-X-9411 ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Display Unit Index IN-1
Related manuals
Manual 89 pages 1.46 Kb

SC-110 specifications

The Furuno SC-110 is a sophisticated marine navigation system designed for a wide array of maritime applications. This advanced device showcases Furuno’s commitment to quality and innovation, making it a popular choice among boat owners, commercial vessels, and maritime professionals.

At the heart of the SC-110 is its precise Positioning Differential GPS (DGPS) technology. This cutting-edge systems enhances the accuracy of standard GPS operations, enabling users to obtain real-time positioning with an impressive level of precision. The SC-110 offers positioning accuracy within one meter, vital for navigation safety and efficiency, particularly in congested or challenging maritime environments.

One of the standout features of the Furuno SC-110 is its built-in Automatic Identification System (AIS) capability. AIS technology allows the SC-110 to display real-time information about nearby vessels, including their position, course, and speed. This additional situational awareness helps mariners avoid potential collisions, making it an essential component for navigation in busy shipping lanes.

The device also incorporates a user-friendly interface, characterized by a sharp, high-resolution display that is easy to read in various lighting conditions. This ensures that maritime operators can access critical navigation data quickly and without confusion. Additionally, customizable settings allow users to tailor the system to their specific needs, improving overall usability.

Another significant aspect of the Furuno SC-110 is its robust integration capabilities. The system can seamlessly connect with other onboard electronic equipment, such as radar systems, chart plotters, and autopilots. This interoperability enhances operational efficiency, allowing mariners to control all their navigational tools from a singular platform.

The SC-110 is designed to withstand the rigors of the marine environment. Built with durable materials and an IP67 waterproof rating, it provides reliable performance even in harsh weather conditions. This resilience ensures that the system will serve maritime operators effectively over time without compromising functionality.

In summary, the Furuno SC-110 represents a blend of advanced technology and practical usability. Its high-precision DGPS, AIS integration, user-friendly interface, and robust construction make it an invaluable tool for safe and efficient maritime navigation. Whether for leisure boating or commercial operations, the SC-110 stands as a testament to Furuno’s expertise in the marine electronics field.
Top Page Image Contents