Furuno SC-110 manual Replacement of Battery, Battery Location Type Code No

Page 58

3. MAINTENANCE, TROUBLESHOOTING

3.6Replacement of Battery

The processor unit has a battery that stores data when the power is turned off. When the battery voltage is low, the message “BATTERY!” appears on the display. Have a qualified technician replace the battery, following the procedure below. The life of the battery is 3-5 years.

Battery Location

Type

Code No.

Processor Unit

CR2450-F2ST2L

000-144-941

1.Press the [MENU] key to open the menu.

2.Choose SYS SETUP and then press the [ENT] key.

3.Choose “EXCHANGE BATTERY?” and then press the [ENT] key.

EXCHANGE BATT?

ARE YOU SURE?

YES

NO

Prompt for exchanging battery

4.Press ◄ to choose YES and then press the [ENT] key. The following message appears.

READY FOR

BATTERY CHANGE.

TURN OFF THE

UNIT.

Prompt for turning off the power

5.At this time the contents of the RAM are temporarily moved to the flash memory. Turn off the power.

6.Have a qualified technician replace the battery.

Note: If the equipped will not be used for a long period of time, save data by following the above procedure. This will prevent loss of data even if the battery dies.

3-8

Page 57 Page 59
Image 58
Page 57 Page 59
Contents THD Satellite Compass 00014854600 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiForeword FeaturesWord to the Owner of the SC-110 System Configuration System configurationOptional equipment Equipment ListStandard supply Name Type Code No Qty RemarksSpecifications of THD Satellite Compass SC-110Coating Color Mounting Considerations InstallationAntenna unit Separation degrees Mast diameter Separation distance minimumAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Unit Installation postFix the antenna unit to the post as shown below Fastening antenna unit to a postCoating bolt, nut and washer with silicone rubber Antenna elementBulkhead mount Installing the Processor UnitBulkhead mount Deck mount Processor unit orientation, deck mountingInstallation of processor unit on the underside of a desk Installation on the underside of a deskMounting on underside of desk Flush mount Installing the Display UnitDesktop, overhead mounting Flush mount FFlush mount S kit Type OP20-17, Code No Flush mount SFlush mount S Wiring WiringHow to install the optional antenna cable set Sectional view of coaxial cable DPYC-1.5How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status Initial SettingsSatellite tracking status display Choosing mounting method Installation setup menuMain menu Connection of External Equipment General wiringProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationControls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displayCompass display Steering displayROT Rate-of-Turn display Speed display SOG/STW displayDgps alarm options Alarm SetupAlarm menu Buzzer optionsConfirming Satellite Status Satellite status displayDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Data OUT1 menu, sentences Baud rate optionsIEC, Nmea version options Tx interval optionsHeading talker options Output sentence limitation Sentence and maximum number of charactersLog pulse Log pulse optionsSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode WAAS/DGPS menu WAAS/DGPS SetupPosition fix mode options Waas Search optionsGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation Others menu Others MenuHDG Restoration options Trip Menu Trip menuReset Distance prompt Resetting Distance RunChoosing External Heading Source for Backup Heading setup menuMAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Test menu options DiagnosticsDiagnostic test1 Test start promptDiagnostic test sequence Display Test Program Number DisplayDiagnostic test2 TEST2 displayAlarm options Diagnostic test3TEST3 menu Program version no. display Program NumberClearing Data Prompts for erasure of dataPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Prompt for turning off the powerError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Data ERRMenu Tree AppendixAP-1 Digital Interface Data Schematic diagramsAP-3 Data OutData sentences AP-4AP-5 GNS Gnns fix dataAP-6 VBW Dual ground/water speedAP-7 VLW Distance travelled through the waterInput/Output Ports Port Terminal Name Signal Remarks LabelAP-8 AP-9 HdthdghdmAP-10 Parts List and Parts LocationProcessor Unit, cover removed AP-11 Display Unit, cover openedGeodetic Chart Codes AP-12Principle of Satellite Compass AP-13What is WAAS? AP-14Ｐａｃｋｉｎｇ Ｌｉｓｔ Page 工事材料表 SC-502-J/E 20AY-X-9404 SC-1101-J/E 20AY-X-9401 Spare Parts List for 20AT-X-9411 ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Display Unit Index IN-1
Related manuals
Manual 89 pages 1.46 Kb

SC-110 specifications

The Furuno SC-110 is a sophisticated marine navigation system designed for a wide array of maritime applications. This advanced device showcases Furuno’s commitment to quality and innovation, making it a popular choice among boat owners, commercial vessels, and maritime professionals.

At the heart of the SC-110 is its precise Positioning Differential GPS (DGPS) technology. This cutting-edge systems enhances the accuracy of standard GPS operations, enabling users to obtain real-time positioning with an impressive level of precision. The SC-110 offers positioning accuracy within one meter, vital for navigation safety and efficiency, particularly in congested or challenging maritime environments.

One of the standout features of the Furuno SC-110 is its built-in Automatic Identification System (AIS) capability. AIS technology allows the SC-110 to display real-time information about nearby vessels, including their position, course, and speed. This additional situational awareness helps mariners avoid potential collisions, making it an essential component for navigation in busy shipping lanes.

The device also incorporates a user-friendly interface, characterized by a sharp, high-resolution display that is easy to read in various lighting conditions. This ensures that maritime operators can access critical navigation data quickly and without confusion. Additionally, customizable settings allow users to tailor the system to their specific needs, improving overall usability.

Another significant aspect of the Furuno SC-110 is its robust integration capabilities. The system can seamlessly connect with other onboard electronic equipment, such as radar systems, chart plotters, and autopilots. This interoperability enhances operational efficiency, allowing mariners to control all their navigational tools from a singular platform.

The SC-110 is designed to withstand the rigors of the marine environment. Built with durable materials and an IP67 waterproof rating, it provides reliable performance even in harsh weather conditions. This resilience ensures that the system will serve maritime operators effectively over time without compromising functionality.

In summary, the Furuno SC-110 represents a blend of advanced technology and practical usability. Its high-precision DGPS, AIS integration, user-friendly interface, and robust construction make it an invaluable tool for safe and efficient maritime navigation. Whether for leisure boating or commercial operations, the SC-110 stands as a testament to Furuno’s expertise in the marine electronics field.
Top Page Image Contents