Furuno SC-110 manual Diagnostics, Diagnostic test1, Test menu options, Test start prompt

Page 53

3. MAINTENANCE, TROUBLESHOOTING

3.3Diagnostics

Diagnostic test1

The diagnostic test1 checks the equipment for proper operation.

Note: Heading is not output during the diagnostic test, and this is communicated with an appropriate message. After completing the diagnostic test, turn the power off and on to update heading data.

1.Press the [MENU] key to open the menu.

2.Choose SYS SETUP and then press the [ENT] key.

3.Choose TEST? and then press the [ENT] key.

TEST1

TEST2

TEST3

Test menu options

4. Confirm that TEST1 is selected and then press the [ENT] key.

TEST START?

(STOP: PWR OFF)

ARE YOU SURE?

YES

Test start prompt

5.Press ◄ to choose YES and then press the [ENT] key. The test proceeds in the sequence shown on the next page.

Note: The output port test (see next page) is intended for the service technician, using a special test connector. If TEST1 is conducted without the test connector, disconnect the DATA IN connector from the processor unit.

3-3

Image 53

Contents THD Satellite Compass 00014854600 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingWord to the Owner of the SC-110 FeaturesForeword System configuration System ConfigurationStandard supply Equipment ListOptional equipment Name Type Code No Qty RemarksSC-110 Specifications of THD Satellite CompassCoating Color Antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Display unit, processor unit Example of antenna installed below superstructuresInstallation post Installing the Antenna UnitFastening antenna unit to a post Fix the antenna unit to the post as shown belowAntenna element Coating bolt, nut and washer with silicone rubberBulkhead mount Installing the Processor UnitBulkhead mount Processor unit orientation, deck mounting Deck mountMounting on underside of desk Installation on the underside of a deskInstallation of processor unit on the underside of a desk Desktop, overhead mounting Installing the Display UnitFlush mount Flush mount FFlush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Wiring WiringSectional view of coaxial cable DPYC-1.5 How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBSatellite tracking status display Initial SettingsConfirming satellite status Main menu Installation setup menuChoosing mounting method Processor unit, cover opened General wiringConnection of External Equipment Cable Sectional view, fabrication Fabrication of cablesDisplay unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Description of displays Choosing a DisplayHeading display Nav data displayROT Rate-of-Turn display Steering displayCompass display SOG/STW display Speed displayAlarm menu Alarm SetupDgps alarm options Buzzer optionsSatellite status display Confirming Satellite StatusGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Baud rate options Data OUT1 menu, sentencesHeading talker options Tx interval optionsIEC, Nmea version options Sentence and maximum number of characters Output sentence limitationLog pulse options Log pulseGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode Position fix mode options WAAS/DGPS SetupWAAS/DGPS menu Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Restoration options Others MenuOthers menu Trip menu Trip MenuChoosing External Heading Source for Backup Resetting Distance RunReset Distance prompt Heading setup menuPreventive Maintenance MAINTENANCE, TroubleshootingSymptom Cause Remedy TroubleshootingTroubleshooting Diagnostic test1 DiagnosticsTest menu options Test start promptDisplay Test Program Number Display Diagnostic test sequenceTEST2 display Diagnostic test2TEST3 menu Diagnostic test3Alarm options Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryPrompt for exchanging battery Prompt for turning off the powerError Messages Replacement of FuseError Message Meaning Remedy Message displayData ERR Error messages con’t from previousAP-1 AppendixMenu Tree Digital Interface AP-3 Schematic diagramsData Data OutAP-4 Data sentencesGNS Gnns fix data AP-5VBW Dual ground/water speed AP-6VLW Distance travelled through the water AP-7AP-8 Port Terminal Name Signal Remarks LabelInput/Output Ports Hdthdghdm AP-9Processor Unit, cover removed Parts List and Parts LocationAP-10 Display Unit, cover opened AP-11AP-12 Geodetic Chart CodesAP-13 Principle of Satellite CompassAP-14 What is WAAS?ＰａｃｋｉｎｇＬｉｓｔ Page 工事材料表 SC-502-J/E 20AY-X-9404 SC-1101-J/E 20AY-X-9401 Spare Parts List for 20AT-X-9411 ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Display Unit IN-1 Index

Related manuals

Manual 89 pages 1.46 Kb

SC-110 specifications

The Furuno SC-110 is a sophisticated marine navigation system designed for a wide array of maritime applications. This advanced device showcases Furuno’s commitment to quality and innovation, making it a popular choice among boat owners, commercial vessels, and maritime professionals.

At the heart of the SC-110 is its precise Positioning Differential GPS (DGPS) technology. This cutting-edge systems enhances the accuracy of standard GPS operations, enabling users to obtain real-time positioning with an impressive level of precision. The SC-110 offers positioning accuracy within one meter, vital for navigation safety and efficiency, particularly in congested or challenging maritime environments.

One of the standout features of the Furuno SC-110 is its built-in Automatic Identification System (AIS) capability. AIS technology allows the SC-110 to display real-time information about nearby vessels, including their position, course, and speed. This additional situational awareness helps mariners avoid potential collisions, making it an essential component for navigation in busy shipping lanes.

The device also incorporates a user-friendly interface, characterized by a sharp, high-resolution display that is easy to read in various lighting conditions. This ensures that maritime operators can access critical navigation data quickly and without confusion. Additionally, customizable settings allow users to tailor the system to their specific needs, improving overall usability.

Another significant aspect of the Furuno SC-110 is its robust integration capabilities. The system can seamlessly connect with other onboard electronic equipment, such as radar systems, chart plotters, and autopilots. This interoperability enhances operational efficiency, allowing mariners to control all their navigational tools from a singular platform.

The SC-110 is designed to withstand the rigors of the marine environment. Built with durable materials and an IP67 waterproof rating, it provides reliable performance even in harsh weather conditions. This resilience ensures that the system will serve maritime operators effectively over time without compromising functionality.

In summary, the Furuno SC-110 represents a blend of advanced technology and practical usability. Its high-precision DGPS, AIS integration, user-friendly interface, and robust construction make it an invaluable tool for safe and efficient maritime navigation. Whether for leisure boating or commercial operations, the SC-110 stands as a testament to Furuno’s expertise in the marine electronics field.