Furuno SC-110 manual Installing the Display Unit, Desktop, overhead mounting, Flush mount F

Page 20

1. INSTALLATION

1.4Installing the Display Unit

1.4.1Desktop, overhead mounting

1.Fasten the hanger to the mounting location with four tapping screws (supplied). See the outline drawing for mounting dimensions.

2.Screw the knobs into the display unit.

3.Set display unit to the hanger and tighten the knobs.

4.Run the ground wire between the ground terminal on the display unit and the ship’s superstructure.

DesktopOverhead

Display unit mounting methods

1.4.2Flush mount

Two types of flush mounts are available. See the outline drawing at the back of the manual for details.

Flush mount “F”

 

 

 

 

Flush mount “F” kit

Type: OP20-29, Code No: 000-041-405)

 

 

 

 

 

 

 

Name

 

Type

Code No.

Qty

 

Cosmetic Panel

 

20-016-1051

100-251-370

1

 

Tapping Screw

 

5X20

000-802-840

4

 

Hex Bolt

 

M6X12

000-862-127

2

 

Spring Washer

 

M6

000-864-260

2

1.Make a cutout in the mounting location. The dimensions are 183(W) x 92(H) mm.

2.Fasten the cosmetic panel to the display unit with hex bolts and spring washers.

3.Fasten the display unit to the mounting location with tapping screws.

1-10

Page 19 Page 21
Image 20
Page 19 Page 21
Contents THD Satellite Compass 00014854600 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiWord to the Owner of the SC-110 FeaturesForeword System Configuration System configurationEquipment List Standard supplyOptional equipment Name Type Code No Qty RemarksSpecifications of THD Satellite Compass SC-110Coating Color Antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Example of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Unit Installation postFix the antenna unit to the post as shown below Fastening antenna unit to a postCoating bolt, nut and washer with silicone rubber Antenna elementBulkhead mount Installing the Processor UnitBulkhead mount Deck mount Processor unit orientation, deck mountingMounting on underside of desk Installation on the underside of a deskInstallation of processor unit on the underside of a desk Installing the Display Unit Desktop, overhead mountingFlush mount Flush mount FFlush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Wiring WiringHow to install the optional antenna cable set Sectional view of coaxial cable DPYC-1.5How to attach connector N-P-8DFB How to attach connector N-P-8DFBSatellite tracking status display Initial SettingsConfirming satellite status Main menu Installation setup menuChoosing mounting method Processor unit, cover opened General wiringConnection of External Equipment Fabrication of cables Cable Sectional view, fabricationDisplay unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Choosing a Display Description of displaysHeading display Nav data displayROT Rate-of-Turn display Steering displayCompass display Speed display SOG/STW displayAlarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Data OUT1 menu, sentences Baud rate optionsHeading talker options Tx interval optionsIEC, Nmea version options Output sentence limitation Sentence and maximum number of charactersLog pulse Log pulse optionsGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Restoration options Others MenuOthers menu Trip Menu Trip menuResetting Distance Run Choosing External Heading Source for BackupReset Distance prompt Heading setup menuMAINTENANCE, Troubleshooting Preventive MaintenanceSymptom Cause Remedy TroubleshootingTroubleshooting Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence Display Test Program Number DisplayDiagnostic test2 TEST2 displayTEST3 menu Diagnostic test3Alarm options Program Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRAP-1 AppendixMenu Tree Digital Interface Schematic diagrams AP-3Data Data OutData sentences AP-4AP-5 GNS Gnns fix dataAP-6 VBW Dual ground/water speedAP-7 VLW Distance travelled through the waterAP-8 Port Terminal Name Signal Remarks LabelInput/Output Ports AP-9 HdthdghdmProcessor Unit, cover removed Parts List and Parts LocationAP-10 AP-11 Display Unit, cover openedGeodetic Chart Codes AP-12Principle of Satellite Compass AP-13What is WAAS? AP-14Ｐａｃｋｉｎｇ Ｌｉｓｔ Page 工事材料表 SC-502-J/E 20AY-X-9404 SC-1101-J/E 20AY-X-9401 Spare Parts List for 20AT-X-9411 ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 Hatai Page Page Page Page Display Unit Index IN-1
Related manuals
Manual 89 pages 1.46 Kb

SC-110 specifications

The Furuno SC-110 is a sophisticated marine navigation system designed for a wide array of maritime applications. This advanced device showcases Furuno’s commitment to quality and innovation, making it a popular choice among boat owners, commercial vessels, and maritime professionals.

At the heart of the SC-110 is its precise Positioning Differential GPS (DGPS) technology. This cutting-edge systems enhances the accuracy of standard GPS operations, enabling users to obtain real-time positioning with an impressive level of precision. The SC-110 offers positioning accuracy within one meter, vital for navigation safety and efficiency, particularly in congested or challenging maritime environments.

One of the standout features of the Furuno SC-110 is its built-in Automatic Identification System (AIS) capability. AIS technology allows the SC-110 to display real-time information about nearby vessels, including their position, course, and speed. This additional situational awareness helps mariners avoid potential collisions, making it an essential component for navigation in busy shipping lanes.

The device also incorporates a user-friendly interface, characterized by a sharp, high-resolution display that is easy to read in various lighting conditions. This ensures that maritime operators can access critical navigation data quickly and without confusion. Additionally, customizable settings allow users to tailor the system to their specific needs, improving overall usability.

Another significant aspect of the Furuno SC-110 is its robust integration capabilities. The system can seamlessly connect with other onboard electronic equipment, such as radar systems, chart plotters, and autopilots. This interoperability enhances operational efficiency, allowing mariners to control all their navigational tools from a singular platform.

The SC-110 is designed to withstand the rigors of the marine environment. Built with durable materials and an IP67 waterproof rating, it provides reliable performance even in harsh weather conditions. This resilience ensures that the system will serve maritime operators effectively over time without compromising functionality.

In summary, the Furuno SC-110 represents a blend of advanced technology and practical usability. Its high-precision DGPS, AIS integration, user-friendly interface, and robust construction make it an invaluable tool for safe and efficient maritime navigation. Whether for leisure boating or commercial operations, the SC-110 stands as a testament to Furuno’s expertise in the marine electronics field.
Top Page Image Contents