Nighthawk KN-COEG-3 manual Where to Install Your CO and Gas Alarm

Page 7

Part One – Your Nighthawk CO and Gas Alarm

Where to Install Your CO and Gas Alarm

WHEN CHOOSING YOUR INSTALLATION LOCATIONS, MAKE SURE YOU CAN HEAR THE ALARM FROM ALL SLEEP- ING AREAS.

Mounting Configuration

Since CO generally mixes well with air, mounting the Nighthawk CO and Gas alarm should depend on the type of explosive Gas you intend to detect. If you are not certain which type of Gas you are using in your home, please read about natural Gas and propane in the introduction on page i.

If you are a user of natural Gas, we recommend you mount your Nighthawk unit high on the wall (no closer than 6 inches from the ceiling) using the extendable cord feature to ensure the earliest opportunity to detect a Natural Gas leak.

If you are a user of propane, we recommend you mount your Nighthawk near the floor (using the direct plug-in feature) to ensure the earliest opportunity to detect a propane leak.

LOCATION

Your Nighthawk CO and Gas alarm should be mounted in or near bedrooms and living areas or wherever you suspect a CO or Gas exposure is likely. It is recommended that you install a Nighthawk CO and Gas alarm on each level of a multi-level home.

In the event of a CO alarm, two self-adhesive labels are includ- ed with the CO and Gas alarm. Add the phone number of your emergency service provider in the space provided. Place one label next to the alarm and one label near a fresh air source such as a door or window.

CAUTION: This alarm will only indicate the presence of carbon monoxide or Gas at the sensor. Carbon monoxide or Gas may be present in other areas.

IMPORTANT: Improper location can affect the sensitive elec- tronic components in this alarm. Please see the next section describing where NOT to install this alarm.

Recommended Locations

Upper Levels of Home

Where Not to Install Your CO and Gas Alarm

To avoid causing damage to the unit, to provide optimum pro- tection, and to prevent unnecessary alarms, follow the direc- tions below where NOT to install this alarm:

It is not recommended that you install this CO and Gas alarm in garages or kitchens. Installation in these areas could lead to nui- sance alarms, may expose the sensor to substances that could damage or contaminate it, or the alarm may not be heard by persons in other areas of the home, especially if they are sleeping.

In the garage, vehicle exhaust can contain some carbon monox- ide. These levels are higher when the engine is first started. Within hours of starting a vehicle and backing it out of the garage, the lev- els present over time can activate the alarm and become a nuisance.

In the kitchen, some Gas appliances can emit a short burst of CO or Gas upon start-up. This is normal. If your CO and Gas alarm is mounted too close to these appliances, it may alarm often and become a nuisance.

If you must install a Nighthawk CO and Gas alarm near a cooking or heating appliance, install AT LEAST 5 feet away from appli-

ance.

DINING KITCHEN BEDROOM BEDROOM

LIVING ROOM

BEDROOM

1-3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Carbon Monoxide and Explosive Gas Alarm Table of Contents Introduction About this User’s GuideQuick Set-Up Guide Setting up your CO and Gas alarm for first time operationAbout Your CO and Gas Alarm Part One Your Nighthawk CO and Gas AlarmDigital Display Nighthawk’s Unique FeaturesWhere Not to Install Your CO and Gas Alarm Where to Install Your CO and Gas AlarmTo rotate adapter How to Install Your AlarmDirect Plug Alarm To installNormal Operating Characteristics Wall Mounted AlarmTable Top Alarm Testing the Electronics How to Test Your AlarmTesting the sensor response Malfunction Signal Group 2 Microprocessor Failure If the alarm malfunctionsMalfunction Signal Group 1 Component Failure Low Battery WarningPeak Level Memory Button How to Know If Your Alarm is MalfunctioningHow to Care for Your Alarm To Reset the Peak Level Memory…Part Two Carbon Monoxide and Gas What You Should Not Do Home Safety Tips What You Can DoClues You Cannot See Mid Levels Part Three What You Should Know Before the Alarm SoundsHigh Levels Common Medium Exposure Symptoms Common Mild Exposure SymptomsCommon Extreme Exposure Symptoms Treatment for CO Poisoning Part Four What to Do if the Alarm Sounds for GasWhat to do if the Alarm Sounds for Gas Do not activate any electrical switch or telephonePart Five Technical Information What happens if the power goes out? Part Six Frequently Asked QuestionsPart Six Frequently Asked Questions Part Six Display Reading and What They Mean Display Shows Alarm Sound Unit StatusDisplay Shows Alarm Sound Unit Status Recommended Action Readings You May See When Unit is AC PoweredPage Wall Mount Diagram Warranty Registration Limited WarrantyPlease send products and all other correspondence to

KN-COEG-3 specifications

The Nighthawk KN-COEG-3 is a state-of-the-art carbon monoxide and explosive gas detector designed to offer paramount safety for homes and workplaces. With its sleek design and advanced technology, this device stands out in the market for its reliability and ease of use. One of the most striking features of the KN-COEG-3 is its dual-function capability, allowing it to detect both carbon monoxide (CO) emitted from sources like gas appliances and vehicles and explosive gases such as natural gas and propane. This dual detection provides an added layer of safety, ensuring that you are alerted to potential dangers in real time.

The device is equipped with a highly sensitive electrochemical sensor for carbon monoxide detection, which offers precise readings and minimizes false alarms. The explosive gas sensor utilizes a catalytic bead technology, which allows for quick identification of dangerous gas leaks. Together, these technologies ensure that you are protected from two of the most serious gas-related hazards.

Another key feature of the Nighthawk KN-COEG-3 is its user-friendly interface. The device includes a well-designed LCD display that provides clear, easy-to-read information regarding the levels of carbon monoxide and explosive gases detected in the air. It also features a loud alarm system that activates immediately upon detection of dangerous levels, ensuring that occupants can promptly respond to evacuation protocols.

The KN-COEG-3 boasts a compact and stylish design, making it easy to install in various locations, whether mounted on a wall or placed on a countertop. It is powered by an AC adapter with a battery backup, which guarantees continuous operation even in the event of a power outage. This reliability ensures peace of mind for users, whether they are at home or away.

Additionally, the device incorporates advanced self-test features that allow it to periodically check its sensor and system functionality, assuring users of its operational integrity. By coupling advanced technology with a commitment to user safety, the Nighthawk KN-COEG-3 presents a compelling solution for anyone looking to enhance their safety against carbon monoxide and explosive gas hazards in their environment.
Top Page Image Contents