Mamiya C28, C32, C24 manual Assembling the Roof Flue KIT, Flue over 3 meters long

Page 22

INSTALLATION

INSTALLATION

22 ASSEMBLING THE ROOF FLUE KIT

Determine the correct height that the flue should terminate above the roof. If after calculating or measuring the overall flue height from the top of the boiler, it is necessary to cut both pipes of assembly A, then ensure they are cut equally leaving the inner flue tube longer than the outer air tube as supplied. (Refer to No. 6 below)

Ensure the cut pipe ends are free from any burrs.

1Ensure the flue seal collar B is located onto the flue assembly A.

2Position the roof flashing plate D (supplied separately) over the hole cut in the roof and insert flue assembly A from the roof end.

3Push fit the vertical connector E (supplied separately) into the boiler flue connection and retain with the screws F (supplied with the vertical connector kit). ENSURING THE

GASKETS IN THE BOILER FLUE OUTLET ARE CORRECTLY FITTED.

4“Push” fit extension duct J (if required (supplied separately)) and the roof flue kit assembly A into the connector E.

5If the last extension duct requires cutting, measure the distance (outer ducts) between the duct and the terminal and add 100 mm to this dimension. This gives the length of the last extension duct.

NOTE. Check the position of the inner flue duct relative to the outer duct on the assembled extension duct(s) and ensure the terminal flue duct is cut longer than the air duct to ensure engagement in the final flue duct seal.

6Slide down and position the flue seal collar B over the roof plate D and secure it with the three screws C to the flue assembly A.

7Finally ensure the roof flashing plate D is correctly sealed to the roof.

8Flue over 3 meters long.

For flues over 3 m long a conensate drain and trap must be fitted. The trap must be connected to a suitable waste pipe. See frame 9 for available trap kit.

1

F

2E

A

A

Ø 100

D

D

J4

E

6

3

Ø 60

5

 

 

o

 

 

 

 

min16

o

 

 

 

max41

A

 

 

 

 

MAX LENGTH:

 

 

C24

--- 8.5

m

 

 

C28

--- 8.5

m

 

 

C32 --- 6 m

B

A A

C C

B

B

D

22

mini HE --- Installation & Servicing

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Installation and servicing Mini HE --- Installation & Servicing Document Amendments Performance Data --- Central Heating GeneralBoiler Data Domestic Hot WaterContents Benchmark Commissioning Checklist DetailsGeneral Boiler Water Connection Boiler ClearancesOptional Extra Kits GAS SafetyIntroduction Safe HandlingSafe Handling of Substances Flue Installation RequirementsGAS Supply Location of Boiler and Flue OutletAIR Supply Water Circulation SystemWater Treatment Additional PumpsElectrical Supply RequirementsSize of expansion vessel Mini HE C24, mini HE C28Hydraulic Loss Remaining pump capacity General Boiler Control Interlocks Domestic HOT Water RequirementsGeneral Boiler Water Circuit Diagram Installation Installation Boiler AssemblyHardware pack contents Installation UnpackingPack a contents Pack B contentsInstallation Fitting the Flue SystemTwin Pipe Rear Flue AssemblyRefer to the following diagram for the model mini HE C32 Flue DuctWall Mounting Template rear flue Ring Installation Cutting the FlueFitting the Extension Kits Installation Fitting the Optional Roof Flue Roof Flue KIT CONTENTS/OPTIONSInstallation Flue Terminal Position Flue ArrangementAssembling the Roof Flue KIT Flue over 3 meters longMounting the Boiler Installation Fitting the Wall Mounting PlateFit the service valves, washers and tail pipes as shown ConnectionsLocate the gasket and flue turret on the top of the boiler Safety Valve DrainCondensate Drain Flues over 1 meter longIncoming mains wiring detail For external controls wiring see frameElectrical Connections Pictorial Wiring Installation Functional Flow Diagram Control pcbExternal Electrical Controls Electrical Connections for a Combi BoilerInstallation Initial Lighting Maximum valve setting To Adjust PressuresMinimum valve setting Electrical Installation Anti Cycling SettingCommissioning and Testing Gas InstallationGeneral Checks Installation GAS Conversion Handing OverServicing Servicing ScheduleServicing Removal of Outer and Inner Casing RE---ASSEMBLY Servicing Burner Removal and CleaningCleaning the Heat Exchanger Burner Pressure CheckServicing FAN and Venturi Removal and Cleaning Remove the fan by sliding it towards left see the arrowBurner Injectors Replacement Spark and Detection Electrode ReplacementBurner Replacement When replacing any componentTemperature Probe Replacement Servicing Overheat Thermostat ReplacementFlue Temperature Probe Replacement Removal of CH temperature probeGAS Valve Replacement Expansion Vessel ReplacementVenturi Replacement Servicing FAN ReplacementAIR Pressure Switch Replacement Pump Replacement Complete Servicing Electronic CONTROL/IGNITION PCB Replacement Boiler mode setting Servicing CH Flow Switch Replacement CH Flow Switch Membrane ReplacementDHW Filter and Flow Limiter Replacement Servicing DHW Flow Switch ReplacementFlow limiter Servicing Primary Heat Exchanger Replacement Recuperator ReplacementServicing Diverter Valve Actuator Replacement Diverter Valve Internal Parts ReplacementServicing DHW Heat Exchanger Replacement CH Drain Cock ReplacementTo clean the condensate trap and drain Condensate Trap ReplacementTo replace the condensate trap Normal operation OFFFault Finding FindingFrom Fault finding Fault Finding Fault Refer back to page 52 of fault finding to continue Fault Finding From Fan mod. mini HE C28, mini HE C32 Burner mod. mini HE C28, mini HE C32075535 17398422 23 Installer Notification Guidelines GAS Boiler Commissioning Checklist Service Interval Record Technical Training Ideal boilersInstaller Water hot or Installer the contact fire not doesCorrectly Ignition at attempt Cleaning MaintenanceGAS of Escape Boiler the Light to Lights DiagnosticClearances Minimum

C28, C24, C32 specifications

The Mamiya C series is celebrated among photography enthusiasts for its unique twin-lens reflex (TLR) design, offering both a classic aesthetic and innovative features that set it apart in the world of medium format cameras. The C32, C24, and C28 models represent a range of technology and design advancements that cater to various shooting needs.

The Mamiya C32, introduced in the early 1970s, is renowned for its precision engineering and versatility. This model features interchangeable lenses, allowing photographers to switch between different focal lengths for creative flexibility. The camera supports 120 and 220 film formats, enabling higher film capacities for extended shooting sessions. An essential feature of the C32 is its built-in light meter, which enhances exposure accuracy by providing real-time readings. The camera's bright waist-level finder offers excellent viewing comfort and composition aid, attracting those who appreciate a more hands-on shooting experience.

Next in line, the Mamiya C24 offers a slightly more compact and lighter design, making it an appealing option for documentary and street photographers. While still featuring the electronic leaf shutter system utilized in the C32, the C24 omits built-in metering, which encourages users to develop their exposure skills. The lens selection remains robust, with options ranging from wide-angle to telephoto, allowing for creative versatility. The C24's rugged build quality and reliable shutter performance make it a trusted companion in various shooting conditions.

Lastly, the Mamiya C28 provides a perfect blend of portability and advanced capabilities. With its ergonomic design and improved lens coatings, the C28 offers enhanced image quality with better contrast and sharpness. Similar to its predecessors, it utilizes an interchangeable lens system but enhances user convenience through quick-to-use shutter speeds and aperture settings. The camera is also compatible with a range of accessories, such as flash units and close-up attachments, further expanding its creative potential.

In summary, the Mamiya C32, C24, and C28 each present unique features and technological advancements that cater to various types of photographers. Whether it's the precision of the C32, the compact convenience of the C24, or the versatile performance of the C28, these cameras maintain a special place in the hearts of medium format enthusiasts, showcasing the blend of craftsmanship and innovation that Mamiya is known for.
Top Page Image Contents