Burnham SERIES 2 manual 54/ANSIZ223.1, Ventdampersequenceofoperation, Effikal and Johnson Damper

Page 11

54/ANSIZ223.1.

15.INSTALLAROOMTHERMOSTATonaninsidewall about four feet above floor. Never install thermostat on an outside wall or where it will be influenced by drafts, hot or cold water pipes, lighting fixtures, television, rays of the sun or near a fireplace. Keep large furniture away from thermostat so there will be free movement of room air around this control.

Heat Anticipator in Thermostat should be set to match the requirements of the control to which it is connected. See Table

4.If system tends to overheat above the thermostat's temperature setting, reduce heat anticipator setting by .1 or.2 amps. If system tends to short cycle without reaching desired room temperature, increase heat anticipator setting by .1 or .2 amps.

16.INSTALLELECTRICWIRINGinaccordancewith National Electric Code or the Canadian Electrical Code and local regulations. See Figures 11 through 14 for applicable wiring diagram. A separate Electrical Circuit should be run from meter with a Fused Disconnect Switch in this Circuit. When installed, the boiler must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, and/or the CSA C22.1 Electrical Code, if an external electrical source is utilized.

For zone valve wiring, a separate 24V transformer is required rather than attempting to use the boiler mounted control. Consult zone valve manufacturer for assistance.

17.VENTDAMPERSEQUENCEOFOPERATION

Effikal and Johnson Damper

 

Figure 8: Typical Vent Installation

 

 

Table 4: Wiring Diagrams and Heat Anticipator Settings

 

 

 

 

 

 

 

 

 

Thermostat Heat

Wiring Diagram

Ignition Type

Circulation Method

 

 

Anticipator Setting [Amps]

Figure Number

Page Number

 

 

 

 

 

 

 

 

 

 

Continuous

Intermittent

0.6

11

13

(Standing Pilot)

 

 

 

 

Constant/Gravity

1.0

14

18

 

 

 

 

 

 

Intermittent

Intermittent

0.6

12

14

 

 

 

 

 

Constant/Gravity

1.0

13

16

 

 

 

 

 

If system tends to overheat above thermostat's temperature setting, reduce heat anticipator setting by 0.1 or 0.2 amps. If system tends to shortcycle without reaching desired room temperature, increase heat

anticipator setting by 0.1 or 0.2 amps.

11

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PartNo.81417032R10-11/99 Price $3.00Page 202 Remove Crate ClearancesCanada Determine type of space. Divide Volume by Total Input Length Inch w.c. Pressure Drop Feet BoilerpipingOxygen Corrosion Equivalent Length of Fittings InstallblockedventswitchRefer to in this manual Seal any unused openings in the common venting system IfanexistingboilerisremovedBoth of the aforementioned standards, Ansi Plug-in Damper Installation Effikal and Johnson Damper 54/ANSIZ223.1Ventdampersequenceofoperation Vent Damper Schematic Wiring Diagram Sequence of Operation Normal Operation Safety ShutdownPage Vent Damper will close see Paragraph 17E Page Pilot Sequence of Operation Normal Operation Wiring Schematic, Zone Valves Initial Start Section II Operating InstructionsTop View of SV9500, SV9600 VR Gas Valves 21460147 For Your Safety Read Before Operating Lighting Instructions 81460177Check Pilot Burner Flame Check GAS Input Rate to BoilerLP Gas Input Combustion Chamber BURN-OFF Check Ignition System Safety SHUT-OFF DeviceMove Jumper Typical Pilot Flame, Honeywell Q3450 Troubleshooting Guide, Honeywell Intermittent Ignition Section III Service Burner Cleaning and Installation Pilot Burner and Gas Valve LubricationManifold and Main Burners Contact Regional Office Indicated for your State Burnham Corporation Regional OfficesSection Assembly and Canopy Group Canopy Assembly Key Description Boiler Qty Base AssemblyUSS Manifold and Main Burners Inch Main Burners Manifold and Main Burners 1 Inch Main Burners Only Key Description QuantityManifold and Main Burners Mm Main Burners Manifold and Main Burners 50 mm Main Burners Only Volt Continuous Ignition Standing Pilot LP Gas Only 40MM Main Burners onlyIntermittent Ignition Only Volt Continuous Ignition Standing Pilot Natural Gas OnlyNatural G as, Sea Level to 2000 Ft Burner Only 40mm Burner Only Burner Only 40mm Burner Only 40mm Burners Only Service Notes Key Quantity Description Key Description Quantity Water Trim Nipple, 1¼ NPT x 806600005 Transformer Continuous and Gravity Circulation Only Vent Reducer Draft Hood CartonVent Damper Carton U.S.A. Standard Canada Optional

SERIES 2 specifications

The Burnham SERIES 2 is a highly regarded addition to the lineup of residential and commercial heating systems, known for its efficiency, reliability, and innovative design. Designed with the user in mind, the SERIES 2 boasts a range of main features that cater to the needs of modern heating solutions.

One of the standout characteristics of the Burnham SERIES 2 is its advanced cast iron construction. This material is renowned for its durability and excellent heat retention capabilities, ensuring that the system provides consistent warmth over extended periods. The cast iron heat exchanger allows for efficient heat transfer and maximizes energy output while minimizing heat loss.

Efficiency is a key focus for the Burnham SERIES 2, and it is designed to operate at high annual fuel utilization efficiency (AFUE) ratings. With its efficiency-enhancing features, including advanced combustion technology, the system helps homeowners save on energy costs while reducing their environmental footprint. The SERIES 2’s design helps ensure that a greater percentage of the fuel consumed is converted into usable heat, making it a smart choice for energy-conscious users.

Another significant feature is the versatile configuration options available with the Burnham SERIES 2. It can be installed in various settings, including basements, utility rooms, or even garages, due to its compact design. The system is compatible with multiple fuel types, allowing users to select between natural gas and propane to suit their specific preferences and availability.

The Burnham SERIES 2 also prioritizes ease of maintenance. Its user-friendly design includes access panels that simplify servicing and routine inspections. Additionally, it incorporates a range of safety features, such as an automatic shut-off system and built-in controls, to ensure safe operation.

In terms of technology, the SERIES 2 utilizes an innovative control system that optimizes heating cycles based on user demands and external conditions. This intelligent control enhances comfort and prevents excessive cycling, thereby prolonging the lifespan of the unit.

Overall, the Burnham SERIES 2 is distinguished by its robust construction, energy-efficient operation, versatility in installation, ease of maintenance, and advanced technology. For homeowners and businesses seeking a reliable heating solution, it represents a compelling choice, delivering warmth and comfort while remaining mindful of energy consumption and environmental impact.
Top Page Image Contents