Desa CB36P Optional Hand-Held, Optional GWMS2 ON/OFF Wall Mounted Switch, Variable Control Knob

Page 22

Operating Fireplace

Continued

IMPORTANT: Be sure to press the ON/ OFF buttons on hand-held remote control unit for up to 3 seconds to assure proper operation.

2.Press ON/OFF button to turn the burner on and off.

optional Hand-Held

REMOTE OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, page 31). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions, page 21.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere be- tween HI and LO. Slide the selector switch to the REMOTE position (see Figure 36).

Note: Burner may light if hand-held remote was on when selector switch was last turned off. You can now turn burner on and off with hand-held remote control unit.

IMPORTANT: Do not leave selector switch in the REMOTE or ON position when pilot is not lit. This will drain battery.

To Lock press both buttons on hand-held remote control until light stops flashing. Hand- held remote control is now locked. If fire is on it will be turned off automatically. In locked state, light will not light up when any button is pressed.

To Unlock press both buttons together on hand-held remote control until light stops flashing. Hand-held remote is now unlocked.

Indicator

LightControl

Button

Figure 37 - On/Off Hand-Held Remote

Control Unit HRC100

OPTIONAL GWMS2

ON/OFF WALL

MOUNTED SWITCH

WARNING: Do not connect

Blower Control Knob (Optional Accessory)

OFF ON

REMOTE

OFF

ON

Variable Control Knob

N

 

 

O

 

L

 

T

 

O

I

O

 

O

H

L

 

 

I

F

 

 

P F

 

 

 

 

 

the appliance gas controls to a 120 VAC power source. Damage or injury may occur.

Light fireplace as instructed in Lighting Instructions on page 21 . If using an HRC remote with a wall switch, set remote selec- tor switch to the ON position (see Figure 36).

Gas Control Knob

Selector Switch in in ON Position

Remote Position

Figure 36 - Setting the Selector Switch,

Gas Control Knob and Variable Control

Knob for Remote Operation

On/Off Series Model HRC100

Hold control button on hand-held remote until burner turns on. Hold control button again until burner turns off (see Figure 37).

Wall switch may now be used to turn burner flame ON and OFF.

To turn fireplace off, turn wall switch and/or remote selector switch to the OFF position and turn gas control knob back to PILOT. Pilot will remain lit.

IMPORTANT: To turn pilot off, turn gas control knob on heater to the OFF position.

22

www.desatech.com

117437-01D

Page 21 Page 23
Image 22
Page 21 Page 23
Contents
Models VCB36NE and VCB36PETable of Contents Safety Product Identification Local CodesPre-Installation Preparation Product FeaturesLocation and space requirements Framing and Finishing Packaging and RemovalClearances Ceiling to Louver & Front91.4 cm 36 1/4 92.1 cm 14 3/4 37.5 cmMantel Depth Opening Mantel from14 35.6 cm Installation Precautions Venting InstallationVenting Installation Electrical Supply Connection Checking for Proper VentingRelilef With Strain Relief Installing Optional Wall Mount Switch GWMS2 Installing Optional ControlsHigh Altitude Installation Installing Remote ReceiverRemote Receiver Installing and Activating the Remote ReceiverPlastic Mounting Clips IgnitionMillivolt Wiring Diagram Wiring DiagramsInstallation Items Needed Fireplace InstallationInstalling Gas Piping to Fireplace Location Check GAS TypeConnecting Fireplace to GAS Supply Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Fireplace Gas ConnectionsLouver Panels and Glass Door Equipment Shutoff Valve Gas Meter Gas ValveRemoving/Replacing Glass Door Removing Louver PanelsSpring Clips Glass Panel Frame RailInstalling Logs and Glowing Embers Lighting Instructions Manual Ignition System For your safety Read before lightingOperating Fireplace To Turn OFF GAS To ApplianceElectronic Ignition System Lighting Instructions Manual Lighting ProcedureOptional Wireless Remote Operation RodOn/Off Series Model HRC100 Optional GWMS2 ON/OFF Wall Mounted SwitchOptional Hand-Held Variable Control KnobInspecting Burners Pilot AssemblyAir Adjustment Setting Burner Flame PatternsGlass Door Cleaning and MaintenancePilot and Burners Service Hints SpecificationsTechnical Services Observed Problem Possible Cause Remedy TroubleshootingOr replace ODS/pilot assembly Replace gas regulator Low Natural gas company Burner porting or orifice Pilot is lit or cycles duringHave the vent system CloggedOrifice, adjust air shutter Glass soots Flame impingement on Adjust the log set so LogsClogged burner tube Clean burner tube Burner air adjustmentObserved Problem Possible Cause Remedy Gas leak. See Warning Statement aboveReplacement Parts AccessoriesParts Wire Harness Assembly Burner Assembly Complete See pages 30Damper Assembly Louver AssemblyParts KEY Description QTY Limited Warranty Vent Fireplace WarrantyKeep this Warranty 07/07