Heat & Glo LifeStyle GEM42 manual Safety And Warning Information, Prohibited

Page 2
SAFETY AND WARNING INFORMATION

SAFETY AND WARNING INFORMATION

READ and UNDERSTAND all instructions carefully

!before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty.

!Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the Owners Guide.

DO NOT USE this appliance if any part has been

!under water. Immediately CALL a qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

!THIS UNIT IS NOT FOR USE WITH SOLID FUEL. Installation and repair should be PERFORMED by a

!qualified service person. The appliance and venting system should be INSPECTED before initial use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is IMPERATIVE that the unit’s control compartment, burners, and circulating air passageways BE KEPT CLEAN to provide for adequate combustion and ventilation air.

Always KEEP the appliance clear and free from

!combustible materials, gasoline, and other flammable vapors and liquids.

!NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the appliance CLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should

!be LOCATED out of traffic areas and away from furniture and draperies. Clothing or flammable material SHOULD NOT BE PLACED on or near the appliance.

!Children and adults should be ALERTED to the hazards of high surface temperature and should STAY AWAY to avoid burns or clothing ignition. Young children should be CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units MUST use one of the vent systems

!described in the Installing the Fireplace section of the Installers Guide. NO OTHER vent systems or components MAY BE USED.

This gas fireplace and vent assembly MUST be

!vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas appliance MUST USE a separate vent system. Common vent systems are

PROHIBITED.

INSPECT the external vent cap on a regular basis to

!make sure that no debris is interfering with the air flow.

!The glass door assembly MUST be in place and sealed, and the trim door assembly MUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass

!door removed, cracked, or broken. Replacement of the glass door should be performed by a licensed or qualified service person. DO NOT strike or slam the glass door.

!The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied by the gas fireplace manufacturer. NO SUBSTITUTE material may be used.

!DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is

!recommended that a qualified service technician perform an appliance check-up at the beginning of each heating season.

!Any safety screen or guard removed for servicing must be replaced before operating this appliance.

!DO NOT place furniture or any other combustible household objects within 36 inches of the fireplace front.

2

Heat & Glo • GEM42 • 371-900 Rev. N • 2/05

Image 2
Contents GEM42 ModelInstallers Guide Underwriters Laboratories ListedREAD and UNDERSTAND all instructions carefully SAFETY AND WARNING INFORMATIONThis gas fireplace and vent assembly MUST be DO NOT USE this appliance if any part has beenService Parts Lists TABLE OF CONTENTSSafety and Warning Information Section 3 Installing the Fireplace5 Log set assembly Service PartsGEM42 NG, LP Exploded Parts DiagramACCESSORIES / ACCESSOIRES Service Parts List / Liste des pièces de rechangeGEM42 Valve Assembly Intermittent Pilot Ignition1Approvals and Codes Installation CodesHigh Altitude Installations Appliance CertificationIntroducing the Heat & Glo Gas Fireplaces Pre-install Preparation2Getting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the GEM42 Heat & Glo GEM42 371-900 Rev. N 2/05Step 1. Locating the Fireplace 3Installing the FireplaceConstructing the Fireplace Chase Fireplace Dimensions, Locations47-1/2” Step 2. Framing the FireplaceFigure 3. Framing Dimensions 47-3/4”NOTE PIPES OVERLAP 1-1/4 INCHES AT EACH JOINT DVP90STTEMS OR COMPONENTS MAY BE USED Step 3. Installing the Vent SystemA. Vent System Approvals Identifying Vent ComponentsFlue Restrictor Instructions Pilot Shield AdjustmentSTRAIGHT UP VERTICAL VENTING V FT 40 MAX. 12.4 MELBOWS VENTING WITHTWO 2 90 o VENTING WITH ONE 1 90 ELBOWVENTING WITH THREE 3 90 ELBOWS V FTH FT H + H 1 FTVenting Out the Top Vent B. Installing Vent Components3. Install Support Brackets 1. Attach the First Vent Component to the Starting CollarsFigure 15. 10 x 12 Hole and Vent Pipe 4. Install FirestopsCut a 10-inch by 12-inch 254mm X 305mm hole through the wall Figure 16. Heat Shield, Interior & Exterior FirestopsWARNING THE TERMINATION CAP MUST BE C. Vent TerminationAttic Firestop POSITIONED SO THAT THE ARROW IS POINT- ING UPnot to be installed above a gas = AREA WHERE TERMINAL IS NOT PERMITTEDelectrical service meter/regulator assembly withinFigure 22. Minimum Height from Roof to Lowest Discharge Opening Step 4. Positioning, Leveling and Securing the FireplaceWARNING MAJOR U.S. BUILDING CODES SPECIFY MINIMUM CHIMNEY AND/OR Figure 23. Proper PositioningHeat-Zone Kit Step 5. Installing the Optional Heat-Out or Heat-Zone KitsHeat-Out Kit Step 6 The Gas Control SystemPressure Step 7. The Gas Supply LineStep 8. Gas Pressure Requirements Natural GasIntermittent Pilot Ignition IPI Wiring 3 Volt Transformer Step 9. Wiring the FireplaceFigure 26. Intermittent Pilot Ignition IPI Wiring Diagram Operation with Battery Back-upWARNING WHEN FINISHING THE FIREPLACE Step 10. FinishingFigure 27. Fan Wiring Diagram FINISH WALL MATERIALFigure 31. Facing Template Dimensions IMPORTANT INSTALLATION NOTEFacing Requirements Facing Thickness from 3/4” to 1-1/4”Figure 34. Glass Assembly Step 11. Installing Trim, Logs and Ember MaterialInstalling the Trim Glass Specifications GEM42 CERAMICStep 13. Lighting the Fireplace After the InstallationStep 12. Before Lighting the Fireplace Double-check for faulty componentsCleaning Flame Sensor Rod IPI Systems Frequency Annually Fireplace Maintenance4Maintaining and Servicing Your Fireplace Cleaning Glass Door