Bryant 580F operation manual CO2 Sensor Standard Settings

percent of outside-air entering the building for a given damper position. For best results there should be at least a 10 degree difference in outside and return-air temperatures.

(TO x	OA	) + (TR x	RA	) = TM
	100		100

TO = Outdoor-Air Temperature

OA = Percent of Outdoor Air

TR = Return-Air Temperature

RA = Percent of Return Air

TM = Mixed-Air Temperature

Once base ventilation has been determined, set the mini- mum damper position potentiometer to the correct position.

The same equation can be used to determine the occupied or maximum ventilation rate to the building. For example, an output of 3.6 volts to the actuator provides a base ventilation rate of 5% and an output of 6.7 volts provides the maximum ventilation rate of 20% (or base plus 15 cfm per person). Use Fig. 33 to determine the maximum setting of the CO2 sensor. For example, a 1100 ppm set point relates to a 15 cfm per person design. Use the 1100 ppm curve on Fig. 33 to find the point when the CO2 sensor output will be 6.7 volts. Line up the point on the graph with the left side of the chart to deter- mine that the range configuration for the CO2 sensor should be 1800 ppm. The EconoMi$erIV controller will output the

6.7volts from the CO2 sensor to the actuator when the CO2 concentration in the space is at 1100 ppm. The DCV set point may be left at 2 volts since the CO2 sensor voltage will be ignored by the EconoMi$erIV controller until it rises above the 3.6 volt setting of the minimum position potentiometer.

Once the fully occupied damper position has been deter- mined, set the maximum damper demand control ventilation potentiometer to this position. Do not set to the maximum position as this can result in over-ventilation to the space and potential high-humidity levels.

CO2 Sensor Configuration

The CO2 sensor has preset standard voltage settings that can be selected anytime after the sensor is powered up. See Table 12.

Use setting 1 or 2 for Bryant equipment. See Table 12.

1.Press Clear and Mode buttons. Hold at least 5 sec- onds until the sensor enters the Edit mode.

2.Press Mode twice. The STDSET Menu will appear.

3.Use the Up/Down button to select the preset number. See Table 12.

4.Press Enter to lock in the selection.

5.Press Mode to exit and resume normal operation.

The custom settings of the CO2 sensor can be changed any- time after the sensor is energized. Follow the steps below to change the non-standard settings:

1.Press Clear and Mode buttons. Hold at least 5 sec- onds until the sensor enters the Edit mode.

2.Press Mode twice. The STDSET Menu will appear.

3.Use the Up/Down button to toggle to the NONSTD menu and press Enter.

4.Use the Up/Down button to toggle through each of the nine variables, starting with Altitude, until the desired setting is reached.

5.Press Mode to move through the variables.

6.Press Enter to lock in the selection, then press Mode to continue to the next variable.

Dehumidification of Fresh Air with DCV Control

Information from ASHRAE indicates that the largest humid- ity load on any zone is the fresh air introduced. For some applications, a field-supplied energy recovery unit can be added to reduce the moisture content of the fresh air being brought into the building when the enthalpy is high. In most cases, the normal heating and cooling processes are more than adequate to remove the humidity loads for most com- mercial applications.

If normal rooftop heating and cooling operation is not ade- quate for the outdoor humidity level, an energy recovery unit and/or a dehumidification option should be considered.

Table 12 — CO2 Sensor Standard Settings

			VENTILATION	ANALOG	CO2	OPTIONAL	RELAY
SETTING	EQUIPMENT	OUTPUT	RATE		CONTROL RANGE	RELAY SETPOINT	HYSTERESIS
				OUTPUT
			(cfm/Person)		(ppm)	(ppm)	(ppm)
1		Proportional	Any	0-10V	0-2000	1000	50
				4-20 mA
2	Interface w/Standard	Proportional	Any	2-10V	0-2000	1000	50
	Building Control System			7-20 mA
3		Exponential	Any	0-10V	0-2000	1100	50
				4-20 mA
4		Proportional	15	0-10V	0-1100	1100	50
				4-20 mA
5		Proportional	20	0-10V	0- 900	900	50
				4-20 mA
	Economizer
6		Exponential	15	0-10V	0-1100	1100	50
				4-20 mA
7		Exponential	20	0-10V	0- 900	900	50
				4-20 mA
8	Health & Safety	Proportional	—	0-10V	0-9999	5000	500
				4-20 mA
9	Parking/Air Intakes/	Proportional	—	0-10V	0-2000	700	50
	Loading Docks			4-20 mA

LEGEND

ppm — Parts Per Million

—23—