Hearth and Home Technologies CB4842IR, CB4236IR owner manual Design and Installation Considerations

Page 15

B. Design and Installation Considerations

Heatilator B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring requirements.

Framing and finishing details.

Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the follow- ing tools and building supplies are available.

Gloves

Safety glasses

Tape measure

Framing material

Pliers

Flat blade screwdriver

Hammer

Phillips screwdriver

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Framing square

Level

Reciprocating saw

Manometer

 

1/2 - 3/4 in. length, #6 or #8 Self-drilling screws High temperature caulking material Noncorrosive leak check solution

D. Inspect Appliance and Components

The following B-vent components are needed for installa- tion.

Fireplace Box

Pipe Components

Firestops

Attic Insulation Shield

Elbows

Strapping

Roof Flashing or Chase Top

Termination Cap

Storm Collar

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the log set and appliance grate must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under wa- ter. Call a qualified service technician to inspect the appli- ance and to replace any part of the control system and/or gas control which has been under water.

Heatilator • Caliber BV Series • 4040-262 Rev J • 10/08

15

Image 15
Contents Models CB4236IR CB4842IR Vent Gas Appliance What to do if you smell gasHot glass will cause burns Homeowner Reference Information CongratulationsTable of Contents Installer GuideUser Guide Troubleshooting CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyWarranty Listing and Code Approvals Gas Fireplace Safety Operating InstructionsYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalLighting Instructions IPI For Your Safety Read Before LightingAfter Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceGasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianTypical Appliance System Getting StartedAny such action may cause a fire hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and ComponentsNegative Pressure Model # Framing and ClearancesSelecting Appliance Location Constructing the Appliance ChaseRough Opening Model Width Height Depth ClearancesMantels Mantel and Wall ProjectionsTermination Locations Vent Termination Minimum ClearancesWood or Fuel Oil Termination Vent Information and Diagrams Vent GuidelinesVent System Configuration Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Wall and Ceiling Penetration FramingGas and Electrical Connections Appliance PreparationSecure Vent Sections Installing Vent PipeAssembly of Vent Sections Install Attic Insulation ShieldGas Connection Gas InformationFuel Conversion Gas PressureWiring Requirements Optional Accessories RequirementsElectrical Information Wall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingAppliance Setup Install the Log Assembly Glass AssemblyFirescreen Install Louvers and Trim Air Shutter SettingHood Troubleshooting Symptom Possible Cause Corrective ActionIntellifire Ignition System Range. Replace pilot if any damage is detected Reference Materials Appliance Dimension DiagramCB4236IR Service Parts ListCB4842IR IPI Valve Assembly Optional Components Model # Description Contact Information

CB4842IR, CB4236IR specifications

Hearth and Home Technologies introduces the CB4842IR and CB4236IR, two premium fireplace options designed to enhance the ambiance and warmth of any space. Both models combine modern technology with elegant design, making them ideal choices for contemporary homes.

The CB4842IR features a large viewing area, measuring 48 inches wide, which provides an impressive visual display of the flames. Its contemporary design allows for a seamless integration into various interior styles, from rustic to minimalist. On the other hand, the CB4236IR, with its 42-inch width, offers a slightly more compact option, perfectly suited for smaller spaces without sacrificing style or warmth.

Both models utilize advanced infrared technology, which provides efficient heat distribution while maintaining a comfortable and inviting atmosphere. This technology ensures that the warmth is evenly radiated throughout the room, creating a cozy environment even in larger areas. Additionally, the infrared heat is effective in penetrating objects and surfaces, resulting in a feeling of warmth that is deeply satisfying.

A standout feature of these fireplaces is the customizable flame settings that allow users to adjust the ambiance to their preference. With multiple flame color options, users can choose from traditional yellow flames to vibrant blue hues, adding a personal touch to the fireplace experience. This feature is particularly useful for setting the mood during different occasions, whether it's a romantic dinner or a lively gathering with friends.

Both the CB4842IR and CB4236IR come equipped with user-friendly controls, enabling easy operation from anywhere in the room. Additionally, they offer programmable thermostats for precise temperature control, further enhancing user convenience and energy efficiency.

Safety features are paramount with Hearth and Home Technologies, and both models include built-in safety mechanisms such as automatic shutoff functions. This ensures peace of mind, whether you're at home or away. Furthermore, the fireplaces are designed for easy maintenance, with features that simplify cleaning and upkeep.

In conclusion, the Hearth and Home Technologies CB4842IR and CB4236IR fireplaces combine aesthetic appeal with advanced heating technology. With customizable flame settings, user-friendly controls, and robust safety features, these models stand out as premium options for anyone looking to enhance their living space with a touch of elegance and warmth. Whether for functionality or style, these fireplaces cater to the needs of modern homeowners, blending seamlessly into any décor.