Hearth and Home Technologies CB4236IR, CB4842IR Electrical Information, Wiring Requirements

Page 26

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120 VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (Intellifire ignition).

A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

Plug the 3-volt AC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

C. Optional Accessories Requirements

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

B. Intellifire Ignition System Wiring

D. Electrical Service and Repair

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 12.1. Intellifire Pilot Ignition (IPI) Wiring Diagram.

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

Optional SPST

Wall Switch

OR

Optional Remote

GRN*

BLU

WHT

* GRN wire only used with optional wall switch

WSK-MLT-HTL

Battery

Pack

 

-

+

To

 

+

-

Junction

Limit

Box

 

 

Switch

 

 

3V

 

 

 

 

 

Adaptor

 

 

 

BLK

 

BLK

 

RED

 

 

 

 

 

 

BRN

 

RED

 

 

 

 

 

Valve

Ignitor

Flame

Control

Sensor

 

Box ORG

Pilot Assembly

 

 

WHT

BLK

 

ORG

 

GRN

 

Figure 12.1 Intellifire Pilot Ignition (IPI) Wiring Diagram

26

Heatilator • Caliber BV Series • 4040-262 Rev J • 10/08

Image 26
Contents Hot glass will cause burns Models CB4236IR CB4842IR Vent Gas ApplianceWhat to do if you smell gas Congratulations Homeowner Reference InformationUser Guide Table of ContentsInstaller Guide Troubleshooting Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityWarranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceFor Your Safety Read Before Lighting Lighting Instructions IPIFrequently Asked Questions After Fireplace is LitMaintenance and Service Maintenance Tasks-HomeownerMaintenance Tasks-Qualified Service Technician Gasket Seal and Glass Assembly InspectionGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a fire hazardNegative Pressure Constructing the Appliance Chase Framing and ClearancesSelecting Appliance Location Model #Clearances Rough Opening Model Width Height DepthMantel and Wall Projections MantelsWood or Fuel Oil Termination Termination LocationsVent Termination Minimum Clearances Vent System Configuration Vent Information and DiagramsVent Guidelines Wall and Ceiling Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Vertical Penetration FramingAppliance Preparation Gas and Electrical ConnectionsInstall Attic Insulation Shield Installing Vent PipeAssembly of Vent Sections Secure Vent SectionsGas Pressure Gas InformationFuel Conversion Gas ConnectionElectrical Information Wiring RequirementsOptional Accessories Requirements Junction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialAppliance Setup Firescreen Install the Log AssemblyGlass Assembly Hood Install Louvers and TrimAir Shutter Setting Intellifire Ignition System TroubleshootingSymptom Possible Cause Corrective Action Range. Replace pilot if any damage is detected Appliance Dimension Diagram Reference MaterialsService Parts List CB4236IRCB4842IR IPI Valve Assembly Optional Components Model # Description Contact Information

CB4842IR, CB4236IR specifications

Hearth and Home Technologies introduces the CB4842IR and CB4236IR, two premium fireplace options designed to enhance the ambiance and warmth of any space. Both models combine modern technology with elegant design, making them ideal choices for contemporary homes.

The CB4842IR features a large viewing area, measuring 48 inches wide, which provides an impressive visual display of the flames. Its contemporary design allows for a seamless integration into various interior styles, from rustic to minimalist. On the other hand, the CB4236IR, with its 42-inch width, offers a slightly more compact option, perfectly suited for smaller spaces without sacrificing style or warmth.

Both models utilize advanced infrared technology, which provides efficient heat distribution while maintaining a comfortable and inviting atmosphere. This technology ensures that the warmth is evenly radiated throughout the room, creating a cozy environment even in larger areas. Additionally, the infrared heat is effective in penetrating objects and surfaces, resulting in a feeling of warmth that is deeply satisfying.

A standout feature of these fireplaces is the customizable flame settings that allow users to adjust the ambiance to their preference. With multiple flame color options, users can choose from traditional yellow flames to vibrant blue hues, adding a personal touch to the fireplace experience. This feature is particularly useful for setting the mood during different occasions, whether it's a romantic dinner or a lively gathering with friends.

Both the CB4842IR and CB4236IR come equipped with user-friendly controls, enabling easy operation from anywhere in the room. Additionally, they offer programmable thermostats for precise temperature control, further enhancing user convenience and energy efficiency.

Safety features are paramount with Hearth and Home Technologies, and both models include built-in safety mechanisms such as automatic shutoff functions. This ensures peace of mind, whether you're at home or away. Furthermore, the fireplaces are designed for easy maintenance, with features that simplify cleaning and upkeep.

In conclusion, the Hearth and Home Technologies CB4842IR and CB4236IR fireplaces combine aesthetic appeal with advanced heating technology. With customizable flame settings, user-friendly controls, and robust safety features, these models stand out as premium options for anyone looking to enhance their living space with a touch of elegance and warmth. Whether for functionality or style, these fireplaces cater to the needs of modern homeowners, blending seamlessly into any décor.