Hearth and Home Technologies TIARAI-BK-B, TIARAI-CES, TIARA II-B 1Listing and Code Approvals

1Listing and Code Approvals

A. Appliance Certification

MODEL	Tiara I B
LABORATORY	OMNI-Test Laboratories, Inc.
	061-S-43b-5
TYPE	Vented Gas Fireplace Heater
STANDARD	ANSI Z21.88-2002 ּ CSA 2.33-2002
	UL307b ּ CAN/CBA 2.17-M91
MODEL	Tiara II B
LABORATORY	OMNI-Test Laboratories, Inc.
	061-S-44b-5
TYPE	Vented Gas Fireplace Heater
STANDARD	ANSI Z21.88-2002 ּ CSA 2.33-2002
	UL307b ּ CAN/CBA 2.17-M91

C. Specifications

Model	Maximum		Minimum		Orifice		*Steady			**P.4
	Input		Input		Size		State
(US or Canada)									%
	BTU		BTU				Efficiency
						%
Tiara I B	31,000	22,000		.106		81.43			57.33
(NG)
Tiara I B	30,000	23,000		.063		82.75			56.39
(LP)
Model	Maximum		Minimum		Orifice		*Steady			**P.4
	Input		Input		Size		State
(US or Canada)										%
	BTU		BTU				Efficiency
							%
Tiara II B	38,500		27,000		.120		81.36			60.97
(NG)
Tiara II B	39,000		30,500		.073		83.62			64.14
(LP)
*Maximum Vent Blower On								**Canada Only

D. High Altitude Installations

The product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recre- ational Vehicles” and "Gas Fired Appliances for use at High Altitudes".

Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

When installed, the appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

B. Glass Specifications

This appliance is equipped with 5mm ceramic glass behind the curved glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

Omni-Test Laboratories, Inc. listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and 0 to 4500 feet in Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

E. Non-Combustible Materials

Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C, shall be considered non-combustible materials.

F. Combustible Materials

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other materials that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

Page 4 Heat & Glo · Tiara I B & Tiara II B · 7010-149M August 1, 2008