Hearth and Home Technologies Soho24B owner manual Install Metal Roof Flashing

Page 24

F. Install Metal Roof Flashing

Note: Skip this section if using the RF4-8.

•See minimum vent heights for various pitched roofs (Figure 8.11) to determine the length of pipe to extend through the roof.

•Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 8.12.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 8.11 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing could cause water entry.

•Caulk the gap between the roof flashing and the outside diameter of the pipe.

•Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 8.12.

CAULK

Figure 8.12

G. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.

•Connect both halves of the storm collar with two screws (see Figure 8.13).

•Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

•Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 8.14).

•Caulk around the top of the storm collar (see Figure 8.20).

Figure 8.13 Assembling the Storm Collar

Figure 8.14 Assembling the Storm Collar Around the Pipe

24

Heat & Glo • Soho24B • 2137-900 Rev. H • 10/08

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Soho24B What to do if you smell gasHot glass will cause burns Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsInstallation to ensure maximum safety and benefit Getting StartedTools and Supplies Needed Framing and Clearances Selecting Appliance LocationMantel Projections Constructing the Appliance Chase ClearancesTermination Locations Vent Termination Minimum ClearancesSee .4 for specific clearances Alcove Applications Vent Information and Diagrams Vent Table KeyUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Minimum MaximumTop Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 MaxTop Vent Vertical Termination No Elbow V1 = 45 ft Max .72 m V1 = 3 ft Min mmV1 Minimum H1 Maximum V1 + Top Vent Vertical Termination Three Elbows V1 Minimum H1+ H2 Maximum V1+ V2 MinimumVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Pipe SLPInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Top VentSecuring and Leveling the Appliance Proper Positioning, LevelingInstalling Vent Pipe Assemble Vent SectionsAssemble Slip Sections Secure the Vent SectionsInstall Decorative Ceiling Components Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarInstall RF4-8 Apply Sealant TOP & Partial SidesInstall Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap 22 Venting through the wallGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Electrical InformationJunction Box Installation GRN wire Ground attached To GRN screw with Inside boxFinishing Facing MaterialSee for combustible/non-combustible definitions Appliance Setup Clean the ApplianceAccessories Remove Shipping MaterialsStone Placement Soho24B Positioning StonesNo Stones in this Area Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceTurn off all electric power to the appliance Lighting Instructions IPIFinal inspection by Frequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Intellifire Ignition SystemSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Recommend addition of screen if one is not presentAppliance Dimension Diagram Appliance Dimensions TableReference Materials Location Inches MillimeterVent Components Diagrams SL Series ComponentsElbow RF4-8Roof Flashing Ceiling Firestop Support Effective Height/LengthSnorkel Support Box-BlackAdapter Ceiling Firestop BlackService Parts Part number list on followingStocked At DepotNo longer available IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

Soho24B specifications

Hearth and Home Technologies has once again pushed the boundaries of home heating with the introduction of the Soho24B. This innovative gas fireplace is designed to provide warmth and comfort, while also serving as a striking centerpiece for any living space. A blend of modern aesthetics and advanced technology, the Soho24B delivers a variety of features that elevate the standard of home fireplaces.

One of the standout features of the Soho24B is its sleek and minimalist design, which allows it to seamlessly integrate into contemporary living environments. With a focus on clean lines and an elegant finish, it offers an unobtrusive yet sophisticated look. The large glass viewing area ensures that the dancing flames are always visible, creating a cozy ambiance that enhances any room.

Equipped with advanced burner technology, the Soho24B produces realistic flame patterns that can be customized to suit personal preferences. Users can adjust the flame height and intensity using an intuitive remote control, allowing for both mood lighting and powerful heat output. The versatility of the fireplace makes it suitable for various settings, from intimate family gatherings to lively social events.

Safety is paramount, and the Soho24B is designed with multiple features to ensure worry-free operation. The unit includes an automatic shut-off mechanism that activates when the appliance is not properly ventilated or if it overheats. Additionally, the unit’s glass surface remains cool to the touch when in operation, providing peace of mind for families with young children or pets.

Efficiency is another key characteristic of the Soho24B. Engineered with energy-efficient technology, it ensures maximum heat output with minimal fuel consumption. The fireplace adheres to strict environmental regulations, making it an eco-friendly option for homeowners looking to reduce their carbon footprint without sacrificing comfort.

Moreover, the Soho24B can be installed in both vented and vent-free configurations, offering flexibility to homeowners regarding their heating needs and architectural constraints. This adaptability, combined with the unit’s powerful heating capabilities, makes it an excellent choice for any room in the house.

In summary, the Hearth and Home Technologies Soho24B stands out as a perfect fusion of style, technology, and efficiency. Its stunning design, user-friendly features, and commitment to safety make it a compelling option for those seeking a reliable and beautiful heating solution for their home. Whether you are cozying up on a chilly evening or entertaining friends, the Soho24B creates a warm and inviting atmosphere that is hard to beat.
Top Page Image Contents