Hearth and Home Technologies Soho24B owner manual Install Vertical Termination Cap

Page 26

I. Install Vertical Termination Cap

•Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

•Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 8.20).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 8.20

J. Install Decorative Wall Components

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the firestop.

•Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

•Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 8.21.

K.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thick- ness.

•DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 8.22).

•Heat shields must overlap 1-1/2 in. (38 mm) mini- mum.

There are two sections of the heat shield. One section is factory-attached to the wall shield firestop. The other section is factory-attached to the cap. See Figure 8.22.

If the wall thickness does not allow the required 1-1/2 in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

•If the wall thickness is less than 4-3/8 in. (111 mm), the heat shields on the cap and wall shield firestop must to be trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST be maintained.

•Use an extended heat shield if the finished wall thickness is greater than 7-1/4 in. (184 mm).

•The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2 in. (38 mm) overlap between heat shields.

•Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

•Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields may not be field constructed.

Figure 8.21 Wall Thimble

26

Heat & Glo • Soho24B • 2137-900 Rev. H • 10/08

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Hot glass will cause burns Model Soho24BWhat to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsTools and Supplies Needed Installation to ensure maximum safety and benefitGetting Started Mantel Projections Framing and ClearancesSelecting Appliance Location Constructing the Appliance Chase ClearancesSee .4 for specific clearances Termination LocationsVent Termination Minimum Clearances Alcove Applications Use of Elbows Vent Information and DiagramsVent Table Key Measuring StandardsTwo Elbows Vent DiagramsTop Vent Horizontal Termination One Elbow Minimum MaximumTop Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 MaxV1 Minimum H1 Maximum V1 + Top Vent Vertical Termination No ElbowV1 = 45 ft Max .72 m V1 = 3 ft Min mm Top Vent Vertical Termination Three Elbows V1 Minimum H1+ H2 Maximum V1+ V2 MinimumWall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall PenetrationVertical Penetration Framing Pipe SLPVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Top VentSecuring and Leveling the Appliance Proper Positioning, LevelingInstalling Vent Pipe Assemble Vent SectionsAssemble Slip Sections Secure the Vent SectionsInstall Decorative Ceiling Components Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarInstall RF4-8 Apply Sealant TOP & Partial SidesHeat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components Install Horizontal Termination Cap 22 Venting through the wallGas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Electrical InformationJunction Box Installation GRN wire Ground attached To GRN screw with Inside boxSee for combustible/non-combustible definitions FinishingFacing Material Accessories Appliance SetupClean the Appliance Remove Shipping MaterialsStone Placement Soho24B Positioning StonesNo Stones in this Area Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceFinal inspection by Turn off all electric power to the applianceLighting Instructions IPI After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Recommend addition of screen if one is not presentReference Materials Appliance Dimension DiagramAppliance Dimensions Table Location Inches MillimeterVent Components Diagrams SL Series ComponentsRoof Flashing Ceiling Firestop Support ElbowRF4-8 Effective Height/LengthAdapter SnorkelSupport Box-Black Ceiling Firestop BlackService Parts Part number list on followingNo longer available StockedAt Depot IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

Soho24B specifications

Hearth and Home Technologies has once again pushed the boundaries of home heating with the introduction of the Soho24B. This innovative gas fireplace is designed to provide warmth and comfort, while also serving as a striking centerpiece for any living space. A blend of modern aesthetics and advanced technology, the Soho24B delivers a variety of features that elevate the standard of home fireplaces.

One of the standout features of the Soho24B is its sleek and minimalist design, which allows it to seamlessly integrate into contemporary living environments. With a focus on clean lines and an elegant finish, it offers an unobtrusive yet sophisticated look. The large glass viewing area ensures that the dancing flames are always visible, creating a cozy ambiance that enhances any room.

Equipped with advanced burner technology, the Soho24B produces realistic flame patterns that can be customized to suit personal preferences. Users can adjust the flame height and intensity using an intuitive remote control, allowing for both mood lighting and powerful heat output. The versatility of the fireplace makes it suitable for various settings, from intimate family gatherings to lively social events.

Safety is paramount, and the Soho24B is designed with multiple features to ensure worry-free operation. The unit includes an automatic shut-off mechanism that activates when the appliance is not properly ventilated or if it overheats. Additionally, the unit’s glass surface remains cool to the touch when in operation, providing peace of mind for families with young children or pets.

Efficiency is another key characteristic of the Soho24B. Engineered with energy-efficient technology, it ensures maximum heat output with minimal fuel consumption. The fireplace adheres to strict environmental regulations, making it an eco-friendly option for homeowners looking to reduce their carbon footprint without sacrificing comfort.

Moreover, the Soho24B can be installed in both vented and vent-free configurations, offering flexibility to homeowners regarding their heating needs and architectural constraints. This adaptability, combined with the unit’s powerful heating capabilities, makes it an excellent choice for any room in the house.

In summary, the Hearth and Home Technologies Soho24B stands out as a perfect fusion of style, technology, and efficiency. Its stunning design, user-friendly features, and commitment to safety make it a compelling option for those seeking a reliable and beautiful heating solution for their home. Whether you are cozying up on a chilly evening or entertaining friends, the Soho24B creates a warm and inviting atmosphere that is hard to beat.
Top Page Image Contents