Hearth and Home Technologies SL-750TV-D, SL-550TV-D, SL-750TV-IPI-D Junction Box Installation

Page 23

E. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

•Remove the cover plate located on the outer shell right side (see Figure 10.4).

•Install the supplied Romex™ connector in the cover plate.

•Feed the necessary length of wire through the connector.

•Make all necessary wire connections and reattach the cover plate to the outer shell.

If the box is being wired from the INSIDE of the appliance:

•Remove the screw attaching the junction box/recep- tacle to the outer shell, rotate the junction box/recep- tacle inward to disengage it from the outer shell (see Figure 10.4).

•Pull the electrical wires from outside the appliance through this opening into the valve compartment.

•Feed the necessary length of wire through the connector.

•Make all necessary wire connections to the junction box/receptacle and reassemble the junction box/ receptacle to the outer shell.

 

Romex

 

Connector

 

14/2WG

 

Cover Plate

 

outside firebox

WHT

 

BLK

 

WHT

 

BLK

Copper

 

GRN wire

ground attached

to GRN screw with

inside box

GRN wire

 

NOTE: Do NOT wire

Figure 10.4 Junction Box Detail

110VAC to wall switch.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted

 

 

 

 

switch for use with a fan (See Figure 10.5):

 

 

 

 

•

The power supply for the appliance must

 

 

 

SWITCH

 

be brought into a switch box.

MINIMUM 14-3 AWG

 

 

 

 

 

WITH GROUND

 

 

 

• The power can then be supplied from the

 

 

Red

 

 

switch box to the appliance using a mini-

 

 

Black

Black

 

mum of 14-3 with ground wire.

 

 

White

White

 

 

 

Green

Green

•

At the switch box connect the black (hot)

JUNCTION BOX

 

Green

 

Red

Black White

 

 

wire and red (switch leg) wire to the wall

 

 

switch as shown.

 

 

 

POWER

 

 

 

 

SUPPLY WIRES

•

At the appliance connect the black (hot),

 

 

 

SWITCH BOX

 

white (neutral) and green (ground) wires

 

 

 

 

 

to the junction box as shown.

 

 

 

 

•

Add a 1/4 inch insulated female connector

 

 

 

 

 

to the red (switch leg) wire, route it through

Red

 

 

 

 

the knockout in the face of the junction box,

 

 

 

 

 

and connect to the top fan switch connector

 

 

 

 

 

(1/4 inch male) as shown.

Figure 10.5 Fan Control Switch Wiring

 

 

 

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. H • 9/06

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents What to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Models 1Listing and Code ApprovalsGlass Specifications BTU SpecificationsCombustible Materials Specification High Altitude InstallationsNon-Combustible Materials Specification Getting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Mantels or other Combustibles above Appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent System Configuration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Proper Positioning, Leveling and Securing of a Securing and Leveling ApplianceAttaching Vent to Firebox Installing Vent PipeAssembly of Vent Sections Securing Vent SectionsPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Optional Accessories Requirements Recommendation for WireConnecting to the Appliance Intellifire Ignition System WiringGround to Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingRemove Shipping Materials Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-DTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Grilles and Trim Glass AssemblyShutter Settings Screen MeshBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Check Appliance DraftIntellifire Ignition Lighting ApplianceStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Symptom Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Log Set Assembly Service PartsAdditional service part numbers may appear on the following Service Parts ListSL-750TV-D SL-750TV-D 151 SL-950TV-DSL-950TV-D SL-550 / 750 / 950TV-D-IPI Common Parts Serial # Part Number SL-550 / 750 / 950TV-D 10-06 530-510A Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information

SL-950TV-D, SL-750TV-D, SL-550TV-D, SL-550TV-IPI-D, SL-950TV-IPI-D specifications

Hearth and Home Technologies offers an impressive range of gas fireplaces with the SL-750TV-IPI-D, SL-950TV-IPI-D, SL-550TV-IPI-D, SL-550TV-D, and SL-750TV-D models. Each of these fireplaces showcases innovative design, outstanding performance, and advanced technology, making them a perfect choice for any modern home.

The SL-750TV-IPI-D is known for its large viewing area, providing a spectacular flame presentation that is both customizable and efficient. Its advanced IntelliFire® ignition system ensures reliable and easy operation, minimizing the need for manual ignition. This model also offers a balanced flue design that allows for flexible installation options, enhancing its versatility.

Similarly, the SL-950TV-IPI-D boasts a larger firebox, providing even more impressive heat output and increased aesthetics. Its high-efficiency rating ensures that energy consumption is kept low while delivering warmth. This model also utilizes the IntelliFire system, but it is enhanced with LED accent lighting, creating an inviting atmosphere while complementing the fireplace’s flickering flames.

On the smaller end of the spectrum, the SL-550TV-IPI-D combines compact design with remarkable efficiency. Its direct vent technology offers excellent venting options, allowing installation in various locations without compromising on performance. Equipped with adjustable flame settings, homeowners can tailor the experience to their liking, creating the perfect ambiance for any occasion.

The SL-550TV-D model takes a similar approach but focuses on traditional control mechanisms. This version allows users to manage the fireplace with ease through a manual control system while still maintaining the benefits of direct vent technology.

Lastly, the SL-750TV-D version offers a grand fireplace experience. It features a stunning glass front and can serve as a stunning focal point in larger living spaces. The model's durability is paired with elegant aesthetics, ensuring clients receive not just a heating solution but also a piece of art.

Collectively, all five models prioritize efficiency, design, and user-friendly features, ensuring that Hearth and Home Technologies delivers high-performing solutions that meet varied homeowner needs while offering the flexibility of installation and styles that fit seamlessly into any environment. Whether seeking warmth, style, or both, these fireplaces are worthy investments that enhance home living.
Top Page Image Contents