Hearth and Home Technologies SL-950TV-D Maintaining and Servicing Appliance, Before servicing

Page 39

15 Maintaining and Servicing Appliance

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualiﬁed service technician should perform an appliance check-up at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

•Turn off gas.

•Turn off electricity to appliance.

•Disable remote control, if one is present.

•Ensure appliance is completely cooled.

After servicing:

•Replace any screen or barrier that was removed.

•Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualiﬁed technician recommended.

Check:

•Condition of doors, surrounds and fronts.

•Condition of glass, glass assembly and glass seal.

•Obstructions of combustion and ventilation air.

•Condition of logs.

•Condition of ﬁrebox.

•Burner ignition and operation.

•Burner air shutter adjustment

•Gas connections and ﬁttings.

•Obstructions of termination cap.

Clean:

• Glass

•Air passageways, grilles, control compartment

•Burner, burner ports

Risk of:

•Fire

•Delayed ignition or explosion

•Exposure to combustion fumes

•Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial 3-4 hours operation. Longer operation without cleaning glass may cause a permanent white ﬁlm on glass.

When cleaning glass door:

•Avoid striking, scratching or slamming glass.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white ﬁlm.

•Do NOT clean glass when hot.

•Turn off appliance after 3-4 hours of operation and

ALLOW TO COOL.

•Remove and clean glass assembly.

•Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

•Ensure no debris blocks cap.

•Combustible materials blocking cap may ignite.

•Restricted air ﬂow affects burner operation.

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. H • 9/06

39

Image 39

Contents What to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Models 1Listing and Code ApprovalsGlass Speciﬁcations BTU SpeciﬁcationsHigh Altitude Installations Non-Combustible Materials SpeciﬁcationCombustible Materials Speciﬁcation Getting Started Design and Installation ConsiderationsNegative Pressure Inspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Mantels or other Combustibles above Appliance Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent Information and Diagrams Vent GuidelinesVent System Conﬁguration Minimum Vertical Feet Vent Clearances and Framing Pipe Clearances to CombustiblesVertical Penetration Framing Installing Outside Air Kit Damper Assembly Appliance PreparationGas and Electrical Connections Proper Positioning, Leveling and Securing of a Securing and Leveling ApplianceAttaching Vent to Firebox Installing Vent PipeAssembly of Vent Sections Securing Vent SectionsPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Optional Accessories Requirements Recommendation for WireConnecting to the Appliance Intelliﬁre Ignition System WiringGround to Standing Pilot Ignition System WiringWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingRemove Shipping Materials Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-DTAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Grilles and Trim Glass AssemblyShutter Settings Screen MeshBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Check Appliance DraftIntelliﬁre Ignition Lighting ApplianceStanding Pilot Ignition For Your Safety Read Before Lighting InstructionsFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionsStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Appliance Dimension Diagram Appliance Dimensions TableReference Materials Log Set Assembly Service PartsAdditional service part numbers may appear on the following Service Parts ListSL-750TV-D SL-750TV-D 151 SL-950TV-DSL-950TV-D SL-550 / 750 / 950TV-D-IPI Common Parts Serial # Part Number SL-550 / 750 / 950TV-D 10-06 530-510A Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyDo not Discard this Manual Contact Information