Hearth and Home Technologies SL-350TRS-CE-D manual Flue Termination

Page 26

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

FIGURE 32. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NAILS (4 REQUIRED)

RAFTER

 

CEILING

 

CEILING FIRESTOP

 

 

 

FIGURE 33. Attic Firestop

 

C. Flue Termination

CAUTION:

IF EXTERIOR WALLS ARE FINISHED WITH VINYL

 

SIDING, IT IS NECESSARY TO INSTALL THE VINYL

 

PROTECTOR KIT (VPK-DV) TO THE TOP OF THE

 

EXTERIOR FIRESTOP FOR ALL ROUND

 

TERMINATION CAPS).

 

For Horizontal Terminations using the DVP-TRAP

 

To attach and secure the termination to the last section of

 

horizontal flue:

 

• The rear flue heat shield MUST be placed one inch above

 

the top of the flue between the wall shield and the base

 

of the termination cap.

 

• One section of the heat shield is attached to the wall

 

shield. The other is attached to the termination cap in

 

the same manner (see Figure 34).

26

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. N • 10/07

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts SL-350TRS-CE-DNG, LP Service Parts List SL-350TRS-CE-DSL-350TRS-CE-D Appliance Certification Installation RegulationsApprovals and Regulations Advantica Gas Fireplace 90/396/EECGetting Started Diagram of the SL-350TRS-CE-D Recessed Depth 41.3cm Installing the FireplaceClearance Requirements Step Framing Fireplace SectionsFlue System Approvals Identifying Flue ComponentsDVP90ST SL D-Series Flue Component Specifications 102mm inner pipe/168mm outer pipeUse SL D-Series Components only Use DVP-SeriesFlue with One 90 Elbow Use DVP-Series components only Flue with Two 90 ElbowsFlue with TWO 2 90 Elbows Flue with three 90 elbows USE SL D-SERIES Components only Appliance Preparation Top FlueRear Flue Remove the insulation from the outer flue pipeInstalling Flue Components Install Support BracketsInstall Firestops Installing Support BracketsFlue Pipe & Firestop Hole and New Framing MembersFlue Termination For Horizontal Terminations using the SLK-01DA Arrow is Pointing UPTermination cap This also pertains to vertical flue systems installed Vent Termination Minimum Clearances Step Gas Control System Gas Control SystemStep Gas Supply Line Do not USE AN Open Flame to Check for GAS LeaksStep Gas Pressure Requirements Step Wiring FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Standing Pilot Ignition Wiring Diagram Step FinishingStep Installing Trim Logs, Ember Material Sealant Material Installing the TrimLOG Placement Heat & Glo SL-350TRS-CE-D 2033-900 Rev. N 10/07 Glass Assembly Placing the Ember MaterialDouble-check for faulty components Step Before Lighting Fireplace After InstallationReview safety warnings and cautions Double-check for gas leaksFireplace Maintenance Maintaining Servicing Your FireplaceBurner Flame Patterns Standing Pilot Troubleshooting Trouble- shootingCheck the thermopile with a millivolt Placed in this Opening

SL-350TRS-CE-D specifications

Hearth and Home Technologies has consistently delivered innovative and efficient heating solutions, and the SL-350TRS-CE-D is yet another remarkable addition to their lineup. This contemporary gas fireplace combines advanced technology with a sleek design, making it a popular choice for modern homes seeking both aesthetics and functionality.

One of the standout features of the SL-350TRS-CE-D is its impressive heat output. With a maximum input of 35,000 BTUs, this fireplace is capable of heating up to 1,400 square feet, ensuring cozy warmth throughout your living space. The unit employs a powerful fan system that enhances heat distribution, allowing for a comfortable environment on even the coldest days.

In terms of design, the SL-350TRS-CE-D boasts a linear configuration that creates a stunning focal point in any room. Its clean face design without visible vents allows for seamless integration into various interior styles, from minimalist to contemporary. The large glass viewing area provides an unobstructed view of the flame, inviting warmth and ambiance into your home.

The SL-350TRS-CE-D is equipped with advanced technologies that enhance its performance and user experience. It features an electronic ignition system, which ensures quick and reliable ignition, eliminating the hassle of matches or lighters. Additionally, the fireplace comes with a remote control, allowing users to easily adjust the flame height and heat output from the comfort of their seat.

Safety is also a priority with the SL-350TRS-CE-D. The unit includes a safety screen that prevents accidental contact with hot surfaces, making it an ideal choice for homes with children and pets. Moreover, the fireplace is designed with sealed combustion technology, which draws air from outside for combustion, ensuring that indoor air quality remains unaffected.

With its energy efficiency, the SL-350TRS-CE-D operates with a high efficiency rating, making it an environmentally friendly heating option. This not only helps reduce heating costs but also contributes to a sustainable lifestyle.

In conclusion, the Hearth and Home Technologies SL-350TRS-CE-D is a blend of cutting-edge technology, efficient performance, and captivating design. It is an ideal choice for those looking to enhance their living space with a modern gas fireplace that delivers comfort, safety, and style. Whether you're gathering with family or entertaining guests, the SL-350TRS-CE-D provides warmth and ambiance that will be appreciated throughout the cold months.
Top Page Image Contents