Hearth and Home Technologies SL-350TRS-CE-D manual Termination cap

Page 28

Figure 35. Termination cap

For Vertical Terminations - To locate the flue and install the flue sections:

Locate and mark the flue centerpoint on the underside of the roof, and drive a nail through the centerpoint.

Make the outline of the roof hole around the centerpoint nail.

The size of the roof hole framing dimensions depend on the pitch of the roof. There MUST BE a 1-inch (25mm) clearance from the vertical flue pipe to com- bustible materials.

Mark the roof hole accordingly.

Cover the opening of the installed flue pipes.

Cut and frame the roof hole.

Use framing lumber the same size as the roof rafters and install the frame securely. Flashing anchored to the frame must withstand heavy winds.

Continue to install concentric flue sections up through the roof hole and up past the roof line until you reach the appropriate distance above the roof.

To seal the roof hole, and to divert rain and snow from the flue system:

Attach a flashing to the roof using nails, and use a non- hardening mastic around the edges of the flashing base where it meets the roof.

Attach a storm collar over the flashing joint to form a water-tight seal. Place non-hardening mastic around the joint, between the storm collar and the vertical pipe.

Slide the termination cap over the end of the flue pipe and rotate the pipe clockwise 1/4 turn (for SL-D Se- ries) or snap into place (for DVP Series).

28

Heat & Glo • SL-350TRS-CE-D2033-900 Rev. N • 10/07

Image 28
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts SL-350TRS-CE-DNG, LP Service Parts List SL-350TRS-CE-DSL-350TRS-CE-D Installation Regulations Approvals and RegulationsAppliance Certification Advantica Gas Fireplace 90/396/EECGetting Started Diagram of the SL-350TRS-CE-D Clearance Requirements Installing the FireplaceRecessed Depth 41.3cm Step Framing Fireplace SectionsFlue System Approvals Identifying Flue ComponentsDVP90ST SL D-Series Flue Component Specifications 102mm inner pipe/168mm outer pipeUse SL D-Series Components only Use DVP-SeriesFlue with One 90 Elbow Use DVP-Series components only Flue with Two 90 ElbowsFlue with TWO 2 90 Elbows Flue with three 90 elbows USE SL D-SERIES Components only Appliance Preparation Top FlueRear Flue Remove the insulation from the outer flue pipeInstalling Flue Components Install Support BracketsInstall Firestops Installing Support BracketsFlue Pipe & Firestop Hole and New Framing MembersFlue Termination For Horizontal Terminations using the SLK-01DA Arrow is Pointing UPTermination cap This also pertains to vertical flue systems installed Vent Termination Minimum Clearances Step Gas Control System Gas Control SystemStep Gas Supply Line Do not USE AN Open Flame to Check for GAS LeaksFor Standing Pilot Ignition Wiring Appliance Requirements Step Wiring FireplaceStep Gas Pressure Requirements Standing Pilot Ignition Wiring Diagram Step FinishingStep Installing Trim Logs, Ember Material Sealant Material Installing the TrimLOG Placement Heat & Glo SL-350TRS-CE-D 2033-900 Rev. N 10/07 Glass Assembly Placing the Ember MaterialStep Before Lighting Fireplace After Installation Review safety warnings and cautionsDouble-check for faulty components Double-check for gas leaksFireplace Maintenance Maintaining Servicing Your FireplaceBurner Flame Patterns Standing Pilot Troubleshooting Trouble- shootingCheck the thermopile with a millivolt Placed in this Opening

SL-350TRS-CE-D specifications

Hearth and Home Technologies has consistently delivered innovative and efficient heating solutions, and the SL-350TRS-CE-D is yet another remarkable addition to their lineup. This contemporary gas fireplace combines advanced technology with a sleek design, making it a popular choice for modern homes seeking both aesthetics and functionality.

One of the standout features of the SL-350TRS-CE-D is its impressive heat output. With a maximum input of 35,000 BTUs, this fireplace is capable of heating up to 1,400 square feet, ensuring cozy warmth throughout your living space. The unit employs a powerful fan system that enhances heat distribution, allowing for a comfortable environment on even the coldest days.

In terms of design, the SL-350TRS-CE-D boasts a linear configuration that creates a stunning focal point in any room. Its clean face design without visible vents allows for seamless integration into various interior styles, from minimalist to contemporary. The large glass viewing area provides an unobstructed view of the flame, inviting warmth and ambiance into your home.

The SL-350TRS-CE-D is equipped with advanced technologies that enhance its performance and user experience. It features an electronic ignition system, which ensures quick and reliable ignition, eliminating the hassle of matches or lighters. Additionally, the fireplace comes with a remote control, allowing users to easily adjust the flame height and heat output from the comfort of their seat.

Safety is also a priority with the SL-350TRS-CE-D. The unit includes a safety screen that prevents accidental contact with hot surfaces, making it an ideal choice for homes with children and pets. Moreover, the fireplace is designed with sealed combustion technology, which draws air from outside for combustion, ensuring that indoor air quality remains unaffected.

With its energy efficiency, the SL-350TRS-CE-D operates with a high efficiency rating, making it an environmentally friendly heating option. This not only helps reduce heating costs but also contributes to a sustainable lifestyle.

In conclusion, the Hearth and Home Technologies SL-350TRS-CE-D is a blend of cutting-edge technology, efficient performance, and captivating design. It is an ideal choice for those looking to enhance their living space with a modern gas fireplace that delivers comfort, safety, and style. Whether you're gathering with family or entertaining guests, the SL-350TRS-CE-D provides warmth and ambiance that will be appreciated throughout the cold months.