Hearth and Home Technologies SL-350TRS-CE-D Installing Flue Components, Install Support Brackets

Page 23

B. Installing Flue Components

1.Attaching the First Flue Component to the Starting Collars: A. On the REAR of the heater

To attach the first flue component to the starting collars on the rear of the heater make sure that the heater gasket supplied with the heater seals between the first flue component and the outer heater wrap.

Slide the male end of the inner flue of the pipe section over the inner collar on the heater. At the same time,

slide the outer flue over the outer collar on the heater. Push the flue section into the appliance collar until all the lances (see Figure 28) have snapped in place. Tug slightly on the flue to con- firm that it has completely locked into place.

The first 90° elbow installed in the flue system of a rear flueing heater MUST BE in

a vertical position.

FIGURE 28.

B. On the TOP of the heater

To attach the first flue component to the starting collars on the top of the heater:

Lock the flue components into place by sliding the concentric pipe sections with four

(4) equally spaced interior beads into the heater collar or previously installed compo- nent end with four (4) equally spaced indented sections.

When the internal beads of each outer pipe line up, rotate the pipe section clockwise about one quarter (1/4) turn. The flue pipe is now locked together.

Slide the ceramic fiber pad over the first flue section and place it flush to the fireplace. Continue to add vent components.

WARNING: ENSURE THAT THE HEATER GASKET SUPPLIED WITH THE HEATER SEALS BETWEEN THE FIRST FLUE COMPONENT AND THE OUTER HEATER WRAP.

C. Continue Adding Flue Components

To continue adding flue components in accordance with the pre-planned flue system configuration:

Ensure that each succeeding flue component is securely fitted and locked into the preceding component in the flue system. NOTE: Make sure that seams are NOT aligned to prevent unintentional disconnection.

For elbows that are changing the flue direction, two screws minimum should be put in the outer flue at the joint to prevent the elbow from rotating.

3. Install Support Brackets

For Horizontal Runs - The flue system must be supported every five (5) feet (1.5m) of horizontal run by a horizontal pipe support.

To install support brackets for horizontal runs:

Place the pipe supports around the flue pipe.

Nail the pipe supports to the framing members.

Heat & Glo • SL-350TRS-CE-D2033-900 Rev. N • 10/07

23

Image 23
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents SL-350TRS-CE-D Service PartsSL-350TRS-CE-D NG, LP Service Parts ListSL-350TRS-CE-D Advantica Gas Fireplace 90/396/EEC Installation RegulationsApprovals and Regulations Appliance CertificationGetting Started Diagram of the SL-350TRS-CE-D Recessed Depth 41.3cm Installing the FireplaceClearance Requirements Sections Step Framing FireplaceIdentifying Flue Components Flue System ApprovalsDVP90ST 102mm inner pipe/168mm outer pipe SL D-Series Flue Component SpecificationsUse DVP-Series Use SL D-Series Components onlyFlue with One 90 Elbow Flue with Two 90 Elbows Use DVP-Series components onlyFlue with TWO 2 90 Elbows Flue with three 90 elbows USE SL D-SERIES Components only Top Flue Appliance PreparationRemove the insulation from the outer flue pipe Rear FlueInstall Support Brackets Installing Flue ComponentsInstalling Support Brackets Install FirestopsHole and New Framing Members Flue Pipe & FirestopFlue Termination Arrow is Pointing UP For Horizontal Terminations using the SLK-01DATermination cap This also pertains to vertical flue systems installed Vent Termination Minimum Clearances Gas Control System Step Gas Control SystemDo not USE AN Open Flame to Check for GAS Leaks Step Gas Supply LineStep Gas Pressure Requirements Step Wiring FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Step Finishing Standing Pilot Ignition Wiring DiagramSealant Material Installing the Trim Step Installing Trim Logs, Ember MaterialLOG Placement Heat & Glo SL-350TRS-CE-D 2033-900 Rev. N 10/07 Placing the Ember Material Glass AssemblyDouble-check for gas leaks Step Before Lighting Fireplace After InstallationReview safety warnings and cautions Double-check for faulty componentsMaintaining Servicing Your Fireplace Fireplace MaintenanceBurner Flame Patterns Trouble- shooting Standing Pilot TroubleshootingCheck the thermopile with a millivolt Placed in this Opening

SL-350TRS-CE-D specifications

Hearth and Home Technologies has consistently delivered innovative and efficient heating solutions, and the SL-350TRS-CE-D is yet another remarkable addition to their lineup. This contemporary gas fireplace combines advanced technology with a sleek design, making it a popular choice for modern homes seeking both aesthetics and functionality.

One of the standout features of the SL-350TRS-CE-D is its impressive heat output. With a maximum input of 35,000 BTUs, this fireplace is capable of heating up to 1,400 square feet, ensuring cozy warmth throughout your living space. The unit employs a powerful fan system that enhances heat distribution, allowing for a comfortable environment on even the coldest days.

In terms of design, the SL-350TRS-CE-D boasts a linear configuration that creates a stunning focal point in any room. Its clean face design without visible vents allows for seamless integration into various interior styles, from minimalist to contemporary. The large glass viewing area provides an unobstructed view of the flame, inviting warmth and ambiance into your home.

The SL-350TRS-CE-D is equipped with advanced technologies that enhance its performance and user experience. It features an electronic ignition system, which ensures quick and reliable ignition, eliminating the hassle of matches or lighters. Additionally, the fireplace comes with a remote control, allowing users to easily adjust the flame height and heat output from the comfort of their seat.

Safety is also a priority with the SL-350TRS-CE-D. The unit includes a safety screen that prevents accidental contact with hot surfaces, making it an ideal choice for homes with children and pets. Moreover, the fireplace is designed with sealed combustion technology, which draws air from outside for combustion, ensuring that indoor air quality remains unaffected.

With its energy efficiency, the SL-350TRS-CE-D operates with a high efficiency rating, making it an environmentally friendly heating option. This not only helps reduce heating costs but also contributes to a sustainable lifestyle.

In conclusion, the Hearth and Home Technologies SL-350TRS-CE-D is a blend of cutting-edge technology, efficient performance, and captivating design. It is an ideal choice for those looking to enhance their living space with a modern gas fireplace that delivers comfort, safety, and style. Whether you're gathering with family or entertaining guests, the SL-350TRS-CE-D provides warmth and ambiance that will be appreciated throughout the cold months.