Niles Audio SW10WM manual SW10JM INSTALLATION - FLOOR APPLICATION CONTINUED

Page 11
SW10JM INSTALLATION – FLOOR APPLICATION (CONTINUED)

SW10JM INSTALLATION – FLOOR APPLICATION (CONTINUED)

 

Floor

3" Screws

Cover

 

 

 

 

 

7. Install Trim Out Panel to protect cabinet

 

 

 

from debris until trim out using the

 

 

Hole Cut-out

supplied screws.

 

 

 

8. For trim out, remove Trim Out Panel.

9. Install the included floor grille into the cut-

Floor

3" Screws

Grille

 

 

out opening using the same screws from

 

 

 

the Trim Out Panel.

 

 

Hole Cut-out

OPTIONAL: The grille can be painted to match most decors but should be painted before installation. Additionally, paint the grille separately from the loudspeaker frame. For best results when painting the grille, use a spray gun or airless sprayer. Thin the paint to prevent clogging of the grille holes and apply several light coats instead of one heavy one.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI or 1-305-238-4373

 

9

 

Image 11
Contents A N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM SW10WMFOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFER SW10JM In-ceiling/In-floor installation TABLE OF CONTENTSCONGRATULATIONS SW10JM PlacementSW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER INTRODUCTION10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLYNILES SW10JM JOIST MOUNT SUBWOOFER QUALITY YOU CAN COUNT ONTOOLS NEEDED Figure 2. Home Theater layout with SW10JM placement options SW10JM PLACEMENTSW10JM IN-CEILING/IN-FLOOR INSTALLATION Pre-ConstructionFloor SW10JM INSTALLATION - FLOOR APPLICATIONFLOOR APPLICATION - BEFORE FINAL FLOORING APPLIED 2 x Screws SubwooferFront Bracket Subwoofer Rear BracketSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED CONTINUED ON NEXT PAGE FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction staple the template in place for added easeSubwoofer Rear Bracket cut-out opening using the supplied screws 7. Install the included floor grille into theCEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction SW10JM INSTALLATION - CEILING APPLICATION4. Place the SW10JM subwoofer into the brackets 7. For trim out, remove Trim Out Panel SW10JM INSTALLATION - CEILING APPLICATION CONTINUED9. Install the included ceiling grille into the frame CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame Optional AMPLIFIER REQUIREMENTS & WIRINGThe SW10JM has 5-way binding posts that accept all types of wire ends WIRING FOR NEW CONSTRUCTIONPreconstruction package SW10WM WALL MOUNT SUBWOOFERInstallation package The SW10WM Wall Mount subwoofer includes the following itemsFigure 6. Possible home theater layout with SW10WM placement options SW10WM PLACEMENTPre-Construction SW10WM IN-WALL INSTALLATIONTop Bottom Installing the cabinetPreparing the cabinet Installation Package SW10WM IN-WALL INSTALLATION CONTINUEDfirmly all the way around the perimeter 13. Insert the metal grille into the frame pressingFigure 8. 5-way binding posts Figure 7. 1 or more SW10WM connected to the SWA-500SPECIFICATIONS SOLUTIONS TROUBLESHOOTING GUIDEPROBLEM Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 - 3 0 5 - 2 3 8 - 4 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3