Niles Audio SW10JM, SW10WM manual Specifications, Wiring For New Construction

Page 30

SPECIFICATIONS

WIRING FOR NEW CONSTRUCTION

For best results, avoid running speaker wire near AC wiring, as it may induce a 60Hz hum in the audio signal. It’s a good idea to run the speaker wire after the electrical wiring has already been completed, so that you can route the speaker wire at least three feet away from the electrical wiring. If speaker wire and AC wiring must run parallel, install the wire within a metal conduit.

NOTE: THE SW10WM IS DESIGNED FOR INTERIOR INSTALLATIONS BETWEEN STANDARD STUD CONSTRUCTION. INSTALLATION IN OUTDOOR LOCATIONS OR IN MOISTURE-PRONE INTERIOR ENVIRONMENTS SUCH AS INDOOR SWIMMING POOLS OR SAUNAS IS NOT RECOMMENDED.

SPECIFICATIONS

Frequency Response:

SW10JM: 38Hz - 140Hz +/-3dB

SW10WM: 45Hz - 140Hz +/-3dB

Ampliﬁer Power:

SW10JM: For use with SWA-500M only

SW10WM: For use with SWA-500M only

Overall Dimensions (with grille)

SW10JM Joist Mount Subwoofer: 30" W x 9" H x 13.81" D

76.2cm W x 22.9 cm H x 35.1 cm D

SW10WM Wall Mount Subwoofer: 13.780" W x 46.298" H x 3.248" D

35 cm W x 117.6 cm H x 8.25 cm D

Weight

SW10JM Joist Mount Subwoofer: 57.3 lbs (25.8 kg) shipping weight

SW10WM Wall Mount Subwoofer: 47.8 lbs (21.7 kg) shipping weight

28

Image 30

Contents SW10JM SW10WM FOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFERA N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM Placement TABLE OF CONTENTSCONGRATULATIONS SW10JM In-ceiling/In-floor installationINTRODUCTION SW10JM JOIST MOUNT SUBWOOFER SW10WM WALL MOUNT SUBWOOFER10-INCH WOOFER WITH INJECTION MOLDED TCC SW10JM ONLY INSTALLATION FLEXIBILITYFEATURES AND BENEFITS 10-INCH REINFORCED FIBERGLASS CONE WOOFER SW10WM ONLYQUALITY YOU CAN COUNT ON NILES SW10JM JOIST MOUNT SUBWOOFERTOOLS NEEDED SW10JM PLACEMENT Figure 2. Home Theater layout with SW10JM placement optionsSW10JM IN-CEILING/IN-FLOOR INSTALLATION SW10JM INSTALLATION - FLOOR APPLICATION FLOOR APPLICATION - BEFORE FINAL FLOORING APPLIEDPre-ConstructionFloor Subwoofer Rear Bracket SubwooferFront Bracket 2 x ScrewsSW10JM INSTALLATION - FLOOR APPLICATION CONTINUED staple the template in place for added ease FLOOR APPLICATION - COMPLETE INSTALLATIONNew/Existing Construction CONTINUED ON NEXT PAGEFront Bracket 7. Install the included ﬂoor grille into the cut-out opening using the supplied screwsSW10JM INSTALLATION - CEILING APPLICATION CEILING APPLICATION - BEFORE DRYWALL APPLIED Pre-Construction4. Place the SW10JM subwoofer into the brackets SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 9. Install the included ceiling grille into the frame7. For trim out, remove Trim Out Panel CEILING APPLICATION - COMPLETE INSTALLATION New/Existing Construction SW10JM INSTALLATION - CEILING APPLICATION CONTINUED 8. Install the included ceiling grille into the frame AMPLIFIER REQUIREMENTS & WIRING OptionalWIRING FOR NEW CONSTRUCTION The SW10JM has 5-way binding posts that accept all types of wire endsThe SW10WM Wall Mount subwoofer includes the following items SW10WM WALL MOUNT SUBWOOFERInstallation package Preconstruction packageSW10WM PLACEMENT Figure 6. Possible home theater layout with SW10WM placement optionsSW10WM IN-WALL INSTALLATION Pre-ConstructionInstalling the cabinet Preparing the cabinetTop Bottom SW10WM IN-WALL INSTALLATION CONTINUED Installation Package13. Insert the metal grille into the frame pressing ﬁrmly all the way around the perimeterFigure 7. 1 or more SW10WM connected to the SWA-500 Figure 8. 5-way binding postsSPECIFICATIONS TROUBLESHOOTING GUIDE PROBLEMSOLUTIONS Page NILES AUDIO CORPORATION - 1-800-BUY-HIFI or 1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R EN i l e s A u d i o C o r p o r a t i o n 1 - 3 0 5 - 2 3 8 - 4